Zheng Ye
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Zheng Ye has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Jihua Huang
School of materials science and Engineering, University of Science and Technology Beijing, Beijing, P.R. China
4 shared publications Jian Yang
2 shared publications- Jian Yang
Univ Sci & Technol Beijing, Sch Mat Sci & Engn, Beijing 100083, Peoples R China
2 shared publications Shuhai Chen
2 shared publications- Biaobiao Yang
IMDEA Materials Institute, c/Eric Kandel 2, Getafe, 28906 Madrid, Spain
1 shared publication Hongyi Zhu
1 shared publication
Latest Publications
- 26 July 2024
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 125, 512-522
Fabricate high-strength 7075 aluminum alloy joint through double pulse MIG welding process
- 26 July 2024
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 125, 512-522
Fabricate high-strength 7075 aluminum alloy joint through double pulse MIG welding process
- 13 February 2023
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 38 (11) , 1361-1371
Al/steel joining by MIG welding with high frequency heating
6061 Al alloy and commercial steel were joined via the metal inert gas welding (MIG) with auxiliary high-frequency heating. The influence of parameters on the weld appearance and intermetallic compound layer was studied. The results showed that the increase of the high-frequency current voltage and MIG voltage made the intermetallic compounds layer thicken. The appearance of the weld was improved first and then deteriorated when the high-frequency electric voltage was raised. Interfacial tensile strength was relatively high when the interfacial compounds layer was 1 μm to 5 μm thick. Fracture analysis showed that the brittle fracture of the interfacial compound layer was the key factor that affected the joint tensile strength. Optimal process window was suggested: the heat input range of the high-frequency current was 720–810 J/cm, and that of MIG was 575–615 J/cm. The optimal joint presented more than 70% tensile strength of the 6061 Al.
- 13 February 2023
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 38 (11) , 1361-1371
Al/steel joining by MIG welding with high frequency heating
6061 Al alloy and commercial steel were joined via the metal inert gas welding (MIG) with auxiliary high-frequency heating. The influence of parameters on the weld appearance and intermetallic compound layer was studied. The results showed that the increase of the high-frequency current voltage and MIG voltage made the intermetallic compounds layer thicken. The appearance of the weld was improved first and then deteriorated when the high-frequency electric voltage was raised. Interfacial tensile strength was relatively high when the interfacial compounds layer was 1 μm to 5 μm thick. Fracture analysis showed that the brittle fracture of the interfacial compound layer was the key factor that affected the joint tensile strength. Optimal process window was suggested: the heat input range of the high-frequency current was 720–810 J/cm, and that of MIG was 575–615 J/cm. The optimal joint presented more than 70% tensile strength of the 6061 Al.
- 30 June 2019
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 24 (8) , 721-723
Join Al–steel dissimilar metal by novel high frequency electric cooperated arc welding
A novel high frequency electric cooperated arc welding method (HFAW) was developed to join aluminium and steel of 3.0 mm thickness without groove. Owing to the skin effect and proximity effect of high frequency current, a part of welding heat was directly distributed all over weld side wall. Consequently, sound double-sided weld formation was achieved under a low MIG heat input and high welding speed. The average thickness of interfacial layer was limited to 2.3 µm. Benefitted from the balanced heat input and thin interfacial layer, the failure mode of the HFAW joint was necking at Al base metal. For traditional MIG joint, however, poor back weld formation and thick interfacial layer resulted in spontaneous fracture at interface.
- 30 June 2019
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 24 (8) , 721-723
Join Al–steel dissimilar metal by novel high frequency electric cooperated arc welding
A novel high frequency electric cooperated arc welding method (HFAW) was developed to join aluminium and steel of 3.0 mm thickness without groove. Owing to the skin effect and proximity effect of high frequency current, a part of welding heat was directly distributed all over weld side wall. Consequently, sound double-sided weld formation was achieved under a low MIG heat input and high welding speed. The average thickness of interfacial layer was limited to 2.3 µm. Benefitted from the balanced heat input and thin interfacial layer, the failure mode of the HFAW joint was necking at Al base metal. For traditional MIG joint, however, poor back weld formation and thick interfacial layer resulted in spontaneous fracture at interface.