Reza Talebzadeh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Reza Talebzadeh has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Seyed Hossein Moayed
Technical and Vocational University (TVU)
3 shared publications- Reza Beiranvand
Lorestan Univ, Khorramabad, Iran
2 shared publications Ali Mir
Lorestan University, Khorramabad, Iran
1 shared publication- Ali Mir
Faculty of Engineering, Lorestan University, Khorramabad, Iran
1 shared publication Ali Naseri
Imam Hossein University
1 shared publication- Ali Naseri
Imam Hossein University, Tehran, Iran
1 shared publication
Latest Publications
- 18 September 2026
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 58 (11) , 542
GaAs solar cell with hole-transport-layer-free architecture and hollow graphene nanotube front contacts: a mechanism-resolved optical assessment
- 18 September 2026
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 58 (11) , 542
GaAs solar cell with hole-transport-layer-free architecture and hollow graphene nanotube front contacts: a mechanism-resolved optical assessment
- 18 February 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65 (6) , 1955-1964
Plasmon-enhanced CH 3 NH 3 PbI 3 perovskite solar cells using metal nanoparticle–sensitized nanorod structures
In this study, we employed metal nanoparticle-coated nanorod (NR) arrays in the light-absorbing layer of a perovskite (CH 3 NH 3 PbI 3 ) solar cell (PSC). The methodology involved embedding NRs composed of a hole transport layer (HTL) within the active layer, followed by the placement of spherical NPs along the length of the NRs from top to bottom. It leads to a substantial enhancement in both light absorption and current generation due to the surface plasmonic (SP) effects introduced by the nanoparticles (NPs). We explored how different metals and the dimensions of nanorods influence the optical properties, specifically scattering and absorption of nanoparticles used in PSCs. By comparing nanorods made from gold, silver, copper, and aluminum, and adjusting their heights, we assessed their impact on boosting light absorption within the solar cells. Through 3D simulations, the optimal NR height was determined to be 120 nm. A systematic evaluation was conducted on four different types of plasmonic nanoparticle materials. Among these, gold (Au) NPs yielded the highest J sc , resulting in a PCE of 16.13%, which represents an approximate 15% improvement over conventional planar PSC architectures. This work demonstrates that synergistic coupling of nanorod-induced light trapping and plasmonic resonance provides an effective strategy for overcoming the intrinsic absorption limitations of thin perovskite solar cells.
- 18 February 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65 (6) , 1955-1964
Plasmon-enhanced CH 3 NH 3 PbI 3 perovskite solar cells using metal nanoparticle–sensitized nanorod structures
In this study, we employed metal nanoparticle-coated nanorod (NR) arrays in the light-absorbing layer of a perovskite (CH 3 NH 3 PbI 3 ) solar cell (PSC). The methodology involved embedding NRs composed of a hole transport layer (HTL) within the active layer, followed by the placement of spherical NPs along the length of the NRs from top to bottom. It leads to a substantial enhancement in both light absorption and current generation due to the surface plasmonic (SP) effects introduced by the nanoparticles (NPs). We explored how different metals and the dimensions of nanorods influence the optical properties, specifically scattering and absorption of nanoparticles used in PSCs. By comparing nanorods made from gold, silver, copper, and aluminum, and adjusting their heights, we assessed their impact on boosting light absorption within the solar cells. Through 3D simulations, the optimal NR height was determined to be 120 nm. A systematic evaluation was conducted on four different types of plasmonic nanoparticle materials. Among these, gold (Au) NPs yielded the highest J sc , resulting in a PCE of 16.13%, which represents an approximate 15% improvement over conventional planar PSC architectures. This work demonstrates that synergistic coupling of nanorod-induced light trapping and plasmonic resonance provides an effective strategy for overcoming the intrinsic absorption limitations of thin perovskite solar cells.
- 7 April 2023
- Published by Optica Publishing Group in Applied Optics
- Vol. 62 (11) , 2936-2944
All-optical full-adder design based on photonic crystals using nonlinear effects
All-optical logic devices are essential for realizing all-optical signal processing. A full-adder is the basic building block of an arithmetic logic unit used in all-optical signal processing systems. In this paper, we aim to design an ultrafast and compact all-optical full-adder based on the photonic crystal. In this structure, three main inputs are connected to the three waveguides. Also, we have added one input waveguide to create symmetry in the structure and to improve the performance of the device. A linear point defect and two nonlinear rods of doped glass and chalcogenide are used to control the light behavior. The designed structure consists of 21 x 21 dielectric rods with a radius of 114 nm in a square cell and a lattice constant of 543.3 nm. Also, the area of the proposed structure is 130 mu m2, and the maximum delay time of the proposed structure is about 1 ps, which indicates the minimum data rate of 1 THz. The maximum normalized power for low states and the minimum normalized power for high states are obtained as 25% and 75%, respectively. These characteristics make the proposed full-adder appropriate for high-speed data processing systems. (c) 2023 Optica Publishing Group
- 7 April 2023
- Published by Optica Publishing Group in Applied Optics
- Vol. 62 (11) , 2936-2944
All-optical full-adder design based on photonic crystals using nonlinear effects
All-optical logic devices are essential for realizing all-optical signal processing. A full-adder is the basic building block of an arithmetic logic unit used in all-optical signal processing systems. In this paper, we aim to design an ultrafast and compact all-optical full-adder based on the photonic crystal. In this structure, three main inputs are connected to the three waveguides. Also, we have added one input waveguide to create symmetry in the structure and to improve the performance of the device. A linear point defect and two nonlinear rods of doped glass and chalcogenide are used to control the light behavior. The designed structure consists of 21 x 21 dielectric rods with a radius of 114 nm in a square cell and a lattice constant of 543.3 nm. Also, the area of the proposed structure is 130 mu m2, and the maximum delay time of the proposed structure is about 1 ps, which indicates the minimum data rate of 1 THz. The maximum normalized power for low states and the minimum normalized power for high states are obtained as 25% and 75%, respectively. These characteristics make the proposed full-adder appropriate for high-speed data processing systems. (c) 2023 Optica Publishing Group
- 5 February 2023
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 55 (4) , 1-18
Design and simulation of an all-optical priority encoder based on 2-D photonic crystal
- 5 February 2023
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 55 (4) , 1-18
Design and simulation of an all-optical priority encoder based on 2-D photonic crystal
- 7 January 2023
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 55 (3) , 1-17
Design and simulation of an all-optical Fredkin gate based on silicon slab-waveguide in a 2-D photonic crystal
- 7 January 2023
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 55 (3) , 1-17
Design and simulation of an all-optical Fredkin gate based on silicon slab-waveguide in a 2-D photonic crystal
- 6 April 2020
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 52 (4) , 1-11
Very simple all-optical half-subtractor based on two-dimensional photonic crystals
- 6 April 2020
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 52 (4) , 1-11
Very simple all-optical half-subtractor based on two-dimensional photonic crystals
- 23 December 2019
- Published by Optica Publishing Group in Applied Optics
- Vol. 59 (1) , 165-170
Simple and compact optical half-subtractor based on photonic crystal resonant cavities in silicon rods
We propose a very simple and compact structure to realize the subtracting operation using resonant cavities in a photonic crystal structure. The cross section of the structure is 103 µ m 2 and is desirable for integration based on popular planar technology. In the designed subtractor, the cavity was responsible for selecting the wavelength. By changing the boundary rods’ cavity condition, the mode could resonate at the desired frequencies. To have resonant cavities, we introduce four defect rods between the input and the output waveguides. The results exhibit the true performance of the device. We used only silicon rods in the proposed device, and hence it is very simple to be fabricated. The finite-difference time-domain method was used for analyzing the proposed structure. The simulation results show that the contrast ratio of the device is 5 dB. The maximum rise and fall times are 1.5 and 0.5 ps, respectively.
- 23 December 2019
- Published by Optica Publishing Group in Applied Optics
- Vol. 59 (1) , 165-170
Simple and compact optical half-subtractor based on photonic crystal resonant cavities in silicon rods
We propose a very simple and compact structure to realize the subtracting operation using resonant cavities in a photonic crystal structure. The cross section of the structure is 103 µ m 2 and is desirable for integration based on popular planar technology. In the designed subtractor, the cavity was responsible for selecting the wavelength. By changing the boundary rods’ cavity condition, the mode could resonate at the desired frequencies. To have resonant cavities, we introduce four defect rods between the input and the output waveguides. The results exhibit the true performance of the device. We used only silicon rods in the proposed device, and hence it is very simple to be fabricated. The finite-difference time-domain method was used for analyzing the proposed structure. The simulation results show that the contrast ratio of the device is 5 dB. The maximum rise and fall times are 1.5 and 0.5 ps, respectively.
- 11 September 2019
- Published by Walter de Gruyter GmbH in Frequenz
- Vol. 74 (1-2) , 9-15
4-Channel Tunable Optical Demultiplexer Based on Nonlinearity Phenomenon in 2D Resonant Cavity Photonic Crystals
In this paper, we propose a new structure based on photonic crystals to realise a demultiplexing operation for dense wavelength division multiplexing transmission systems. In this demultiplexer, the resonant cavities were responsible for selecting the wavelength. By imposing defect rods to these cavities, the modes could resonate at the desired frequencies. As we wanted to see the nonlinear effects, the material that was chosen for defect rods were doped glass. The refractive index of this glass in 1550 nm is 1.41. Increasing the input power causes variation in the refractive index of defect rods and as a result resonant condition of whole cavity alerts so a tenable demultiplexer can be investigated. Based on the results, the average pass bands of channels are near to 1.5 nm and the channel spacing is approximately 3.95 nm. The proposed demultiplexer acts in a near-complete transmission efficiency and the mean value of the crosstalk was −19 dB.
- 11 September 2019
- Published by Walter de Gruyter GmbH in Frequenz
- Vol. 74 (1-2) , 9-15
4-Channel Tunable Optical Demultiplexer Based on Nonlinearity Phenomenon in 2D Resonant Cavity Photonic Crystals
In this paper, we propose a new structure based on photonic crystals to realise a demultiplexing operation for dense wavelength division multiplexing transmission systems. In this demultiplexer, the resonant cavities were responsible for selecting the wavelength. By imposing defect rods to these cavities, the modes could resonate at the desired frequencies. As we wanted to see the nonlinear effects, the material that was chosen for defect rods were doped glass. The refractive index of this glass in 1550 nm is 1.41. Increasing the input power causes variation in the refractive index of defect rods and as a result resonant condition of whole cavity alerts so a tenable demultiplexer can be investigated. Based on the results, the average pass bands of channels are near to 1.5 nm and the channel spacing is approximately 3.95 nm. The proposed demultiplexer acts in a near-complete transmission efficiency and the mean value of the crosstalk was −19 dB.
- 14 July 2018
- Published by Springer Nature in Photonic Network Communications
- Vol. 36 (3) , 338-343
Simulant designing of an ultra-compact AND, OR logical gates based on two-dimensional photonic crystal waveguides
- 14 July 2018
- Published by Springer Nature in Photonic Network Communications
- Vol. 36 (3) , 338-343
Simulant designing of an ultra-compact AND, OR logical gates based on two-dimensional photonic crystal waveguides