Srinivasan Manickam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Srinivasan Manickam has a total of 95 co-authors. Here are the top co-authors by number of shared publications:
P. Ramasamy
Department of Physics, SSN Research Centre, Sri Sivasubramaniya Nadar College of Engineering, Chennai, India
18 shared publicationsRamasamy Perumalsamy
Research Centre, Sri Sivasubramaniya Nadar College of Engineering, Chennai, India
12 shared publicationsT. Keerthivasan
Graduate School of Engineering, Nagoya University, Nagoya, Japan
8 shared publicationsSugunraj Sekar
Department of Physics, Sri Sivasubramaniya Nadar College of Engineering, Chennai, India
7 shared publicationsMariyappan Raman
Department of Physics Sri Sivasubramaniya Nadar College of Engineering Chennai India
6 shared publicationsG. Aravindan
Sri Sivasubramaniya Nadar Coll Engn, Dept Phys, Chennai 603110, India
5 shared publications
Latest Publications
- 10 September 2026
- Published by Wiley in Crystal Research and Technology
- Vol. 61 (9) , e70166
Comparative Theoretical Analysis of Structural, Electronic, Optical, and Thermoelectric Properties of Sodium‐Based Zinc Halide Perovskites for Photovoltaic Application
Lead‐free halide perovskites have attracted significant attention as next‐generation materials for photovoltaic applications. In this work, Density Functional Theory (DFT) calculations were performed to investigate the structural, electronic, optical, thermoelectric, and photovoltaic performance of NaZnX 3 (X = F, Cl, Br, and I) in its bulk and novel layer phases. The structural optimization confirms the formation of the cubic bulk phase and tetragonal layer phase, while phonon calculations indicate dynamical instability in bulk NaZnBr 3 and NaZnI 3 . The GGA‐PBE electronic band structures, density of states, and electron density analyses reveal that all compounds exhibit indirect bandgap semiconducting nature with mixed ionic‐covalent bonding. The optical properties exhibit a large dielectric response, strong absorption, high optical conductivity, enhanced refractive index, and reflectivity in the ultraviolet region (6–10 eV). The thermoelectric results indicate that the layered phase possesses the highest thermoelectric figure of merit zT of 0.354 at 700 K for NaZnI 3 . SCAPS‐1D device simulations show that the Ni /n‐Si / a‐Si: H / P3HT/ NaZnF 3 / Metal contact heterostructure achieves a maximum simulated power conversion efficiency of 32.58%.
- 10 September 2026
- Published by Wiley in Crystal Research and Technology
- Vol. 61 (9) , e70166
Comparative Theoretical Analysis of Structural, Electronic, Optical, and Thermoelectric Properties of Sodium‐Based Zinc Halide Perovskites for Photovoltaic Application
Lead‐free halide perovskites have attracted significant attention as next‐generation materials for photovoltaic applications. In this work, Density Functional Theory (DFT) calculations were performed to investigate the structural, electronic, optical, thermoelectric, and photovoltaic performance of NaZnX 3 (X = F, Cl, Br, and I) in its bulk and novel layer phases. The structural optimization confirms the formation of the cubic bulk phase and tetragonal layer phase, while phonon calculations indicate dynamical instability in bulk NaZnBr 3 and NaZnI 3 . The GGA‐PBE electronic band structures, density of states, and electron density analyses reveal that all compounds exhibit indirect bandgap semiconducting nature with mixed ionic‐covalent bonding. The optical properties exhibit a large dielectric response, strong absorption, high optical conductivity, enhanced refractive index, and reflectivity in the ultraviolet region (6–10 eV). The thermoelectric results indicate that the layered phase possesses the highest thermoelectric figure of merit zT of 0.354 at 700 K for NaZnI 3 . SCAPS‐1D device simulations show that the Ni /n‐Si / a‐Si: H / P3HT/ NaZnF 3 / Metal contact heterostructure achieves a maximum simulated power conversion efficiency of 32.58%.
- 29 August 2026
- Published by Wiley in Advanced Theory and Simulations
- Vol. 9 (9)
First Principles Investigations on Ruthenium‐Based Semiconductors Heusler Alloys XRuTe (X = Ti, Zr, Hf) for Thermoelectric Applications
In this work, the structural, mechanical, electronic, and thermoelectric characteristics of Ru‐ based half Heusler alloys XRuTe (X = Ti, Zr, Hf) are thoroughly investigated from first‐principles calculations. These studies were carried out with the help of density functional theory (DFT) using the method of generalized gradient approximation and Boltzmann transport theory to understand their thermoelectric performance. The Structural analysis of these half‐Heusler alloys XRuTe (X = Ti, Zr, Hf) confirms that they are thermodynamically stable with negative formation energy and exhibit a cubic phase. According to electronic band structure studies, ZrRuTe and TiRuTe half‐Heusler alloys are semiconductors with a direct bandgap, but HfRuTe half‐Heusler alloy has a very narrow bandgap of 0.0017 eV. The thermoelectric parameters such as Seebeck Coefficient, electrical conductivity, and thermal conductivity are examined in the temperature range of 100–1200 K. The maximum figure of merit (ZT) is achieved under p‐type doping conditions, highlighting the potential of TiRuTe, ZrRuTe, and HfRuTe half‐Heusler alloy materials for high‐temperature thermoelectric applications.
- 29 August 2026
- Published by Wiley in Advanced Theory and Simulations
- Vol. 9 (9)
First Principles Investigations on Ruthenium‐Based Semiconductors Heusler Alloys XRuTe (X = Ti, Zr, Hf) for Thermoelectric Applications
In this work, the structural, mechanical, electronic, and thermoelectric characteristics of Ru‐ based half Heusler alloys XRuTe (X = Ti, Zr, Hf) are thoroughly investigated from first‐principles calculations. These studies were carried out with the help of density functional theory (DFT) using the method of generalized gradient approximation and Boltzmann transport theory to understand their thermoelectric performance. The Structural analysis of these half‐Heusler alloys XRuTe (X = Ti, Zr, Hf) confirms that they are thermodynamically stable with negative formation energy and exhibit a cubic phase. According to electronic band structure studies, ZrRuTe and TiRuTe half‐Heusler alloys are semiconductors with a direct bandgap, but HfRuTe half‐Heusler alloy has a very narrow bandgap of 0.0017 eV. The thermoelectric parameters such as Seebeck Coefficient, electrical conductivity, and thermal conductivity are examined in the temperature range of 100–1200 K. The maximum figure of merit (ZT) is achieved under p‐type doping conditions, highlighting the potential of TiRuTe, ZrRuTe, and HfRuTe half‐Heusler alloy materials for high‐temperature thermoelectric applications.
- Open Access
- 30 July 2026
- Published by Wiley in Advanced Theory and Simulations
- Vol. 9 (8) , e70499
From Electrons to Energy Conversion: A First‐Principles Study of NbYAl (Y = Ni, Pd, and Pt) Half‐Heusler Thermoelectrics
An ab initio investigation of the structural, mechanical, electronic, and thermoelectric properties of Nb‐based half‐Heusler alloys NbYAl (Y = Ni, Pd, and Pt) is presented for high‐temperature energy conversion applications. Total energy optimization confirms that all NbYAl alloys crystallize in the thermodynamically stable half‐Heusler structure. All compounds crystallize in the stable Y3‐type half‐Heusler structure and satisfy mechanical stability criteria, exhibiting ductile behavior. Electronic structure calculations reveal direct band gaps at the X point with band gap values of 0, 0.017, and 0.133 eV for NbNiAl, NbPdAl, and NbPtAl, respectively. Thermoelectric transport properties are evaluated using Boltzmann transport theory within the constant relaxation time approximation over the temperature range of 100–1200 K. The NbPtAl alloy exhibits superior p‐type thermoelectric performance with a maximum ZT ∼0.70 at 1200 K, attributed to its large Seebeck coefficient, high power factor, and reduced lattice thermal conductivity. NbNiAl and NbPdAl shows the lower thermoelectric performance comparing to NbPtAl half‐Heusler alloy. These results highlight NbYAl alloys as promising candidates for high‐temperature thermoelectric applications.
- 30 July 2026
- Published by Wiley in Advanced Theory and Simulations
- Vol. 9 (8) , e70499
Open AccessFrom Electrons to Energy Conversion: A First‐Principles Study of NbYAl (Y = Ni, Pd, and Pt) Half‐Heusler Thermoelectrics
An ab initio investigation of the structural, mechanical, electronic, and thermoelectric properties of Nb‐based half‐Heusler alloys NbYAl (Y = Ni, Pd, and Pt) is presented for high‐temperature energy conversion applications. Total energy optimization confirms that all NbYAl alloys crystallize in the thermodynamically stable half‐Heusler structure. All compounds crystallize in the stable Y3‐type half‐Heusler structure and satisfy mechanical stability criteria, exhibiting ductile behavior. Electronic structure calculations reveal direct band gaps at the X point with band gap values of 0, 0.017, and 0.133 eV for NbNiAl, NbPdAl, and NbPtAl, respectively. Thermoelectric transport properties are evaluated using Boltzmann transport theory within the constant relaxation time approximation over the temperature range of 100–1200 K. The NbPtAl alloy exhibits superior p‐type thermoelectric performance with a maximum ZT ∼0.70 at 1200 K, attributed to its large Seebeck coefficient, high power factor, and reduced lattice thermal conductivity. NbNiAl and NbPdAl shows the lower thermoelectric performance comparing to NbPtAl half‐Heusler alloy. These results highlight NbYAl alloys as promising candidates for high‐temperature thermoelectric applications.
Sustainable Surface Texturing of Monocrystalline Silicon Wafers for Reflectivity Reduction and Enhanced Solar Cell Performance
Surface texturing of monocrystalline silicon (mono‐Si) wafers is essential for minimizing optical reflection and enhancing light absorption, thereby improving photovoltaic conversion efficiency. In this work, three novel ternary acid etching systems HF:HNO 3 :KMnO 4 (HNP), HF:H 2 SO 4 :KMnO 4 (HSP), and HF:H 2 O 2 :KMnO 4 (HHP) were investigated at a fixed volumetric ratio of 3:2:1 with etching durations of 1–3 min at room temperature. For comparison, conventional alkaline texturing using KOH:IPA:DI water (KOH etching) was also performed. The morphological, optical, and electrical properties of the textured wafers were systematically characterized using UV–vis reflectance spectroscopy, Fourier transform infrared spectroscopy (FTIR), field‐emission scanning electron microscopy (FESEM), and minority carrier diffusion parameters (MDP) lifetime measurements. Device‐level performance was further evaluated through PC‐1D simulation. Among the investigated systems, the HHP etchant exhibited superior texturing performance, reducing average reflectance from 30.1% for the planar surface to 8.2%, while maintaining a relatively high minority carrier lifetime of ≈25.6 μs, indicating reduced surface recombination. Compared to KOH:IPA:DI water texturing, HHP provided comparable or better optical and electrical properties. Moreover, the HHP system offers environmental advantages, as H 2 O 2 decomposes into benign by‐products (H 2 O and O 2 ), making it a sustainable and scalable approach for high‐efficiency mono‐Si solar cell fabrication.
Sustainable Surface Texturing of Monocrystalline Silicon Wafers for Reflectivity Reduction and Enhanced Solar Cell Performance
Surface texturing of monocrystalline silicon (mono‐Si) wafers is essential for minimizing optical reflection and enhancing light absorption, thereby improving photovoltaic conversion efficiency. In this work, three novel ternary acid etching systems HF:HNO 3 :KMnO 4 (HNP), HF:H 2 SO 4 :KMnO 4 (HSP), and HF:H 2 O 2 :KMnO 4 (HHP) were investigated at a fixed volumetric ratio of 3:2:1 with etching durations of 1–3 min at room temperature. For comparison, conventional alkaline texturing using KOH:IPA:DI water (KOH etching) was also performed. The morphological, optical, and electrical properties of the textured wafers were systematically characterized using UV–vis reflectance spectroscopy, Fourier transform infrared spectroscopy (FTIR), field‐emission scanning electron microscopy (FESEM), and minority carrier diffusion parameters (MDP) lifetime measurements. Device‐level performance was further evaluated through PC‐1D simulation. Among the investigated systems, the HHP etchant exhibited superior texturing performance, reducing average reflectance from 30.1% for the planar surface to 8.2%, while maintaining a relatively high minority carrier lifetime of ≈25.6 μs, indicating reduced surface recombination. Compared to KOH:IPA:DI water texturing, HHP provided comparable or better optical and electrical properties. Moreover, the HHP system offers environmental advantages, as H 2 O 2 decomposes into benign by‐products (H 2 O and O 2 ), making it a sustainable and scalable approach for high‐efficiency mono‐Si solar cell fabrication.
- 9 April 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (6) , 5321-5340
Design Optimization of Graphite Retort and Predictive Modeling of Optical Properties in Multi-crystalline Silicon for Solar Cell Applications
- 9 April 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (6) , 5321-5340
Design Optimization of Graphite Retort and Predictive Modeling of Optical Properties in Multi-crystalline Silicon for Solar Cell Applications
- 23 March 2026
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 358
Eco-friendly recycling of end-of-life silicon solar panels for reuse in photovoltaic applications
- 23 March 2026
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 358
Eco-friendly recycling of end-of-life silicon solar panels for reuse in photovoltaic applications
- 9 March 2026
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 37 (7) , 527
Anisotropic wet etching with ethanol-assisted KOH for cost-effective high-performance silicon solar cells
- 9 March 2026
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 37 (7) , 527
Anisotropic wet etching with ethanol-assisted KOH for cost-effective high-performance silicon solar cells
- 13 February 2026
- Published by Springer Nature in Silicon
- Vol. 18 (7) , 2477-2494
Surface Texturing of Mono-Crystalline Silicon Wafer Using TMAH and Metal Assisted Etching for the Photovoltaic Industry
- 13 February 2026
- Published by Springer Nature in Silicon
- Vol. 18 (7) , 2477-2494
Surface Texturing of Mono-Crystalline Silicon Wafer Using TMAH and Metal Assisted Etching for the Photovoltaic Industry
- Open Access
- 10 February 2026
- Published by Springer Nature in Materials for Renewable and Sustainable Energy
- Vol. 15 (1)
Performance of π-shaped thermoelectric generator using novel p-type ZrMnZ and n-type Bi2Te3/SiGe alloys for renewable and sustainable energy applications
Energy emitted in the form of heat from various sources can be recovered and converted into usable electricity using thermoelectric generators (TEGs). In this study, the efficiency of a π-shaped thermoelectric module composed of p-type ZrMnZ (Z = In, Pb, Bi) legs and n-type Bi 2 Te 3 /SiGe alloys were investigated using MATLAB simulation software. The module efficiency was analyzed by varying the p-type legs (ZrMnIn, ZrMnPb, and ZrMnBi), n-type legs (Bi 2 Te 3 and SiGe), and electrode materials (Al, Cu, and Ni), while keeping the ceramic plates (Al 2 O 3 ) constant. The thermoelectric properties of the ZrMnZ alloys were evaluated using the WIEN2k code. Subsequently, the thermoelectric module was constructed, and its performance was simulated in MATLAB. The results reveal that the highest efficiency was achieved for the TEG comprising p-type ZrMnBi and n-type SiGe legs with Cu electrodes. Furthermore, it is observed that varying the leg height and incorporating suitable dopants can further enhance the device efficiency. Therefore, this study demonstrates that the half-Heusler alloys ZrMnIn, ZrMnPb, and ZrMnBi are promising candidates for efficient thermoelectric energy conversion applications.
- 10 February 2026
- Published by Springer Nature in Materials for Renewable and Sustainable Energy
- Vol. 15 (1)
Open AccessPerformance of π-shaped thermoelectric generator using novel p-type ZrMnZ and n-type Bi2Te3/SiGe alloys for renewable and sustainable energy applications
Energy emitted in the form of heat from various sources can be recovered and converted into usable electricity using thermoelectric generators (TEGs). In this study, the efficiency of a π-shaped thermoelectric module composed of p-type ZrMnZ (Z = In, Pb, Bi) legs and n-type Bi 2 Te 3 /SiGe alloys were investigated using MATLAB simulation software. The module efficiency was analyzed by varying the p-type legs (ZrMnIn, ZrMnPb, and ZrMnBi), n-type legs (Bi 2 Te 3 and SiGe), and electrode materials (Al, Cu, and Ni), while keeping the ceramic plates (Al 2 O 3 ) constant. The thermoelectric properties of the ZrMnZ alloys were evaluated using the WIEN2k code. Subsequently, the thermoelectric module was constructed, and its performance was simulated in MATLAB. The results reveal that the highest efficiency was achieved for the TEG comprising p-type ZrMnBi and n-type SiGe legs with Cu electrodes. Furthermore, it is observed that varying the leg height and incorporating suitable dopants can further enhance the device efficiency. Therefore, this study demonstrates that the half-Heusler alloys ZrMnIn, ZrMnPb, and ZrMnBi are promising candidates for efficient thermoelectric energy conversion applications.
- 13 January 2026
- Published by Springer Nature in Silicon
- Vol. 18 (5) , 1677-1687
Enhancement of the Efficiency of Silicon Solar Cells through Controlled Chemical Etching
- 13 January 2026
- Published by Springer Nature in Silicon
- Vol. 18 (5) , 1677-1687
Enhancement of the Efficiency of Silicon Solar Cells through Controlled Chemical Etching