Alaaddin Toktaş
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alaaddin Toktaş has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Gülcan Toktaş
Balikesir Universitesi
7 shared publications Mustafa Tayanç
2 shared publications- Nihat Celik
Balıkesir Elektromekanik Sanayi Tesisleri A.Ş, Balıkesir, Türkiye
2 shared publications - A. Göktuğ Kızılçaoğlu
KZ Mechatronics Industry and Trade, Ltd. Co., Balıkesir, Turkey
1 shared publication - Ali Oral
Balikesir University, Faculty of Engineering
1 shared publication Aslan Deniz Karaoglan
1 shared publication
Latest Publications
- 27 August 2026
- Published by Springer Nature in Fibers and Polymers
- Vol. 27 (11) , 5483-5500
Effect of E-glass Roving Geometry, Fiber Volume Fraction, and Matrix Rheology on Tensile and Knot Performance of Melt-Impregnated Thermoplastic Composite Ropes
- 27 August 2026
- Published by Springer Nature in Fibers and Polymers
- Vol. 27 (11) , 5483-5500
Effect of E-glass Roving Geometry, Fiber Volume Fraction, and Matrix Rheology on Tensile and Knot Performance of Melt-Impregnated Thermoplastic Composite Ropes
- 10 July 2025
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 53 (7) , 1518-1527
Recovering of deteriorated iron loss parameter of sheared and perforated grain-oriented electrical steels
This article focuses on improving more efficient electric transformers through research on core steel processing. By examining the mitered and perforated M5 grade grain-oriented electrical steel core components, many trials have been executed to understand and reduce the deteriorating effects of the cutting and perforating discontinuities on the magnetic properties of grain-oriented electrical steel laminations. Specifically, trials and experiments are focused on the no-load loss parameter of laminations and prototype cores. For these purposes, as-cut versus annealed samples are compared using the Epstein frame test with standard and non-standard test samples. Iron loss parameters of non-standard stacked M5 Grade samples showed 3.7% to 6.4% recovery by annealing at 800 °C for 2 hours. By promoting and guiding Epstein frame test results, four units of 40 kVA-rated identical cast-resin type transformer cores were produced. Two sets of legs and yokes of core components were perforated for stacking purposes, and others were processed without centering holes. One was imperforated, and one of the perforated core sets was annealed under vacuum at 750 °C for 3 hours. The remaining two sets were left as-cut. No-load loss measurement of prototype cores executed by gradually leveled induction. Comparison results of prototype no-load loss parameters showed the recovery of iron loss at a ratio of 14.5% to 16.5% as W/kg on perforated cores by the contribution of annealing.
- 10 July 2025
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 53 (7) , 1518-1527
Recovering of deteriorated iron loss parameter of sheared and perforated grain-oriented electrical steels
This article focuses on improving more efficient electric transformers through research on core steel processing. By examining the mitered and perforated M5 grade grain-oriented electrical steel core components, many trials have been executed to understand and reduce the deteriorating effects of the cutting and perforating discontinuities on the magnetic properties of grain-oriented electrical steel laminations. Specifically, trials and experiments are focused on the no-load loss parameter of laminations and prototype cores. For these purposes, as-cut versus annealed samples are compared using the Epstein frame test with standard and non-standard test samples. Iron loss parameters of non-standard stacked M5 Grade samples showed 3.7% to 6.4% recovery by annealing at 800 °C for 2 hours. By promoting and guiding Epstein frame test results, four units of 40 kVA-rated identical cast-resin type transformer cores were produced. Two sets of legs and yokes of core components were perforated for stacking purposes, and others were processed without centering holes. One was imperforated, and one of the perforated core sets was annealed under vacuum at 750 °C for 3 hours. The remaining two sets were left as-cut. No-load loss measurement of prototype cores executed by gradually leveled induction. Comparison results of prototype no-load loss parameters showed the recovery of iron loss at a ratio of 14.5% to 16.5% as W/kg on perforated cores by the contribution of annealing.
- 1 January 2025
- Published by Pamukkale University in Pamukkale University Journal of Engineering Sciences
- Vol. 31 (7)
The Effect of Forming Process on the Corrosion Characteristics of DX51D Galvanized Steel Sheets
Pamukkale University Journal of Engineering Sciences
- 1 January 2025
- Published by Pamukkale University in Pamukkale University Journal of Engineering Sciences
- Vol. 31 (7)
The Effect of Forming Process on the Corrosion Characteristics of DX51D Galvanized Steel Sheets
Pamukkale University Journal of Engineering Sciences
- 17 June 2024
- Published by Taylor & Francis in Australian Journal of Mechanical Engineering
- Vol. 23 (3) , 538-548
Optimisation of machining parameters of AISI 304L stainless steel with the least error method using Taguchi, RSM, and ANN
- 17 June 2024
- Published by Taylor & Francis in Australian Journal of Mechanical Engineering
- Vol. 23 (3) , 538-548
Optimisation of machining parameters of AISI 304L stainless steel with the least error method using Taguchi, RSM, and ANN
- 25 August 2023
- Published by Sakarya University Journal of Science in Sakarya University Journal of Science
- Vol. 27 (4) , 724-734
Mathematical Modelling of Shear Cutting Process of Grain Oriented Electrical Steels Using Regression Modelling
This article proposes a regression model for the shear-cutting process of grain-oriented electrical steel magnetic cores of transformers made from different gages and magnetic properties of steels. In the experimental runs, 3 levels for thickness (230, 270, and 300 µm) and 4 levels for magnetic features of electrical steels are considered. Core steels are supplied as foils and slit to designed lengths in slitting machinery along the rolling direction of coils. The best magnetic features rely on the rolling direction of the coil and the transverse direction of the coil is subject to the shear-cutting process. The result of cutting operations, discontinuities, and degradations in magnetic properties may occur because of deterioration in crystallography and strain gradation on laminated sheets. Shear-cutting process factors have a strong influence on magnetic degradation even the magnitude of the no-load loss of the transformer core. In this study, the mathematical relation between shear cutting factors sheet thickness ST, counts of hits CH, and the response burr length BL is determined using regression modeling. For this purpose, the process parameters of GEORG TBA 400 cut-to-length machinery in use core production is studied. The calculated coefficient of determination is close to almost 1.00 i.e., R2 = 0.9896 which means the factors are sufficient to model the response, and the model is obtained with a good prediction performance. The aim of the present study is building up a useful process control tool for the machinery and raise a discussion alike process in industry.
- 25 August 2023
- Published by Sakarya University Journal of Science in Sakarya University Journal of Science
- Vol. 27 (4) , 724-734
Mathematical Modelling of Shear Cutting Process of Grain Oriented Electrical Steels Using Regression Modelling
This article proposes a regression model for the shear-cutting process of grain-oriented electrical steel magnetic cores of transformers made from different gages and magnetic properties of steels. In the experimental runs, 3 levels for thickness (230, 270, and 300 µm) and 4 levels for magnetic features of electrical steels are considered. Core steels are supplied as foils and slit to designed lengths in slitting machinery along the rolling direction of coils. The best magnetic features rely on the rolling direction of the coil and the transverse direction of the coil is subject to the shear-cutting process. The result of cutting operations, discontinuities, and degradations in magnetic properties may occur because of deterioration in crystallography and strain gradation on laminated sheets. Shear-cutting process factors have a strong influence on magnetic degradation even the magnitude of the no-load loss of the transformer core. In this study, the mathematical relation between shear cutting factors sheet thickness ST, counts of hits CH, and the response burr length BL is determined using regression modeling. For this purpose, the process parameters of GEORG TBA 400 cut-to-length machinery in use core production is studied. The calculated coefficient of determination is close to almost 1.00 i.e., R2 = 0.9896 which means the factors are sufficient to model the response, and the model is obtained with a good prediction performance. The aim of the present study is building up a useful process control tool for the machinery and raise a discussion alike process in industry.
- 27 August 2019
- Published by Taylor & Francis in Transactions of the IMF
- Vol. 97 (5) , 271-276
Determination of Vickers indentation fracture toughness of boronised alloyed ductile iron
In the present study, copper (Cu), nickel (Ni), and molybdenum (Mo)-alloyed ductile iron was pack boronised at 800–850°C for 3–6 h and subsequently the microhardness and the microstructures of boride layers under different process parameters were investigated in detail. Further, Vickers indentation fracture toughness tests were executed on borided surfaces under 200 g load. The fracture toughness of borided layers was estimated separately by a series of equations and the half-length of corner cracks and the half diagonals of Vickers indents were used as variables. Generally, the values of the obtained fracture toughness were found to be higher than those of previous studies. It was found that thinner boride layers were formed at lower boronising temperatures. The highest toughness value and the thickest boride layer were obtained in the sample boronised at 850°C for 6 h.
- 27 August 2019
- Published by Taylor & Francis in Transactions of the IMF
- Vol. 97 (5) , 271-276
Determination of Vickers indentation fracture toughness of boronised alloyed ductile iron
In the present study, copper (Cu), nickel (Ni), and molybdenum (Mo)-alloyed ductile iron was pack boronised at 800–850°C for 3–6 h and subsequently the microhardness and the microstructures of boride layers under different process parameters were investigated in detail. Further, Vickers indentation fracture toughness tests were executed on borided surfaces under 200 g load. The fracture toughness of borided layers was estimated separately by a series of equations and the half-length of corner cracks and the half diagonals of Vickers indents were used as variables. Generally, the values of the obtained fracture toughness were found to be higher than those of previous studies. It was found that thinner boride layers were formed at lower boronising temperatures. The highest toughness value and the thickest boride layer were obtained in the sample boronised at 850°C for 6 h.
- 1 May 2018
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 194, 1-8
Estimating fracture toughness of various matrix structured ductile iron using circumferentially notched tensile bars
- 1 May 2018
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 194, 1-8
Estimating fracture toughness of various matrix structured ductile iron using circumferentially notched tensile bars
- 1 April 2018
- Published by Sakarya University Journal of Science in Sakarya University Journal of Science
- Vol. 22 (2) , 1
İndüksiyonla Sertleştirilmiş 100Cr6 Çeliğinin Aşınma Davranışının İncelenmesi
Burç imalatında kullanılmak üzere 100Cr6 çeliğinin yüzeyi indüksiyon yöntemiyle sertleştirilmiştir. Sertleşen yüzeylerin içyapı ve sertlik dağılımı incelendikten sonra yüzeylere ball-on tipi aşınma deneyleri uygulanmıştır. Aşınma deneyleri oda sıcaklığında, kuru kayma şartlarında, 4,92 mm/s kayma hızında ve değişik yükler (2,5-5-10 N) altında gerçekleştirilmiştir. Aşınma deney sonuçları kütle kaybı yöntemi ile belirlenmiştir. Sürtünme katsayıları deneyler esnasında kaydedilmiştir. Aşınma izleri ve yüzeyleri optik ve tarama elektron mikroskopları ile incelenmiştir. Sonuç olarak, indüksiyonla sertleştirme işlemi ile çeliğin yüzeyinde perlitik fazın yerine martensit fazının oluştuğu ve bu faz sayesinde çeliğin yüzey sertliğinin 2,5 kat arttığı görülmüştür. Aşınma deneylerinde en fazla kütle kaybı 5 N yük uygulandığında elde edilmiştir.
- 1 April 2018
- Published by Sakarya University Journal of Science in Sakarya University Journal of Science
- Vol. 22 (2) , 1
İndüksiyonla Sertleştirilmiş 100Cr6 Çeliğinin Aşınma Davranışının İncelenmesi
Burç imalatında kullanılmak üzere 100Cr6 çeliğinin yüzeyi indüksiyon yöntemiyle sertleştirilmiştir. Sertleşen yüzeylerin içyapı ve sertlik dağılımı incelendikten sonra yüzeylere ball-on tipi aşınma deneyleri uygulanmıştır. Aşınma deneyleri oda sıcaklığında, kuru kayma şartlarında, 4,92 mm/s kayma hızında ve değişik yükler (2,5-5-10 N) altında gerçekleştirilmiştir. Aşınma deney sonuçları kütle kaybı yöntemi ile belirlenmiştir. Sürtünme katsayıları deneyler esnasında kaydedilmiştir. Aşınma izleri ve yüzeyleri optik ve tarama elektron mikroskopları ile incelenmiştir. Sonuç olarak, indüksiyonla sertleştirme işlemi ile çeliğin yüzeyinde perlitik fazın yerine martensit fazının oluştuğu ve bu faz sayesinde çeliğin yüzey sertliğinin 2,5 kat arttığı görülmüştür. Aşınma deneylerinde en fazla kütle kaybı 5 N yük uygulandığında elde edilmiştir.
- 20 December 2017
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- p. 1-9
Karbürlü östemperlenmiş küresel grafitli dökme demirler
Karbürlü östemperlenmiş küresel grafitli dökme demirler, üstün abrasif aşınma dirençlerinin yanında yeterli darbe tokluğuna da sahip olmaları nedeniyle son zamanlarda aşınma uygulamalarında dikkat çeken küresel grafitli dökme demir ailesinin en yeni üyelerinden biridir. Bu dökme demirlerin üretimi için yeni bir teknolojiye veya ek yatırıma ihtiyaç duyulmadığından pek çok aşınma dirençli malzemeye nazaran imalat süreçleri daha kolay ve ucuzdur. Bu çalışmada karbürlü küresel grafitli dökme demirlerin bileşimleri, üretimleri, ısıl işlemi, işlem sonucundaki içyapısı ve aşınma dayanımları detaylı olarak incelenmiştir. Çalışmanın sonucunda, maliyet ve darbe tokluğu göz önüne alındığında; bu dökme demirlerin aşınma performansının yüksek kromlu abrasif aşınma dirençli dökme demirlerinki ile mukayese edilebilir ölçüde olduğu görülmüştür.
- 20 December 2017
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- p. 1-9
Karbürlü östemperlenmiş küresel grafitli dökme demirler
Karbürlü östemperlenmiş küresel grafitli dökme demirler, üstün abrasif aşınma dirençlerinin yanında yeterli darbe tokluğuna da sahip olmaları nedeniyle son zamanlarda aşınma uygulamalarında dikkat çeken küresel grafitli dökme demir ailesinin en yeni üyelerinden biridir. Bu dökme demirlerin üretimi için yeni bir teknolojiye veya ek yatırıma ihtiyaç duyulmadığından pek çok aşınma dirençli malzemeye nazaran imalat süreçleri daha kolay ve ucuzdur. Bu çalışmada karbürlü küresel grafitli dökme demirlerin bileşimleri, üretimleri, ısıl işlemi, işlem sonucundaki içyapısı ve aşınma dayanımları detaylı olarak incelenmiştir. Çalışmanın sonucunda, maliyet ve darbe tokluğu göz önüne alındığında; bu dökme demirlerin aşınma performansının yüksek kromlu abrasif aşınma dirençli dökme demirlerinki ile mukayese edilebilir ölçüde olduğu görülmüştür.
- 13 June 2017
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 32 (2)
MATRİS YAPISININ ve BORLAMA SÜRESİNİN Cu-Ni-Mo ALAŞIMLI KGDD’İN AŞINMA DAVRANIŞINA ETKİSİNİN İNCELENMESİ
Bu çalışmada Cu-Ni-Mo alaşımlı küresel grafitli dökme demirin aşınma davranışı üzerine matris yapının (perlitik, temper martensitik ve ösferritik) ve 800ºC’de borlama süresinin (3, 4.5 ve 6 saat) etkisi araştırılmıştır. Aşınma testleri disk üzerinde ball tipi aşınma cihazında 6,8 N yük altında, 6,5 mm/s kayma hızında, oda sıcaklığında, kuru kayma şartlarında gerçekleştirilmiştir. Borlama işlemiyle, yaklaşık olarak 43-60 µm arasındaki kalınlıklarda tek fazlı (Fe 2 B) bor tabakaları elde edilmiştir. Borlama işlemi ile döküm yapısına göre yaklaşık 3 kat, temper martensitik matris yapısına göre ise 2 kat daha fazla aşınma direnci elde edilmiştir.
- 13 June 2017
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 32 (2)
MATRİS YAPISININ ve BORLAMA SÜRESİNİN Cu-Ni-Mo ALAŞIMLI KGDD’İN AŞINMA DAVRANIŞINA ETKİSİNİN İNCELENMESİ
Bu çalışmada Cu-Ni-Mo alaşımlı küresel grafitli dökme demirin aşınma davranışı üzerine matris yapının (perlitik, temper martensitik ve ösferritik) ve 800ºC’de borlama süresinin (3, 4.5 ve 6 saat) etkisi araştırılmıştır. Aşınma testleri disk üzerinde ball tipi aşınma cihazında 6,8 N yük altında, 6,5 mm/s kayma hızında, oda sıcaklığında, kuru kayma şartlarında gerçekleştirilmiştir. Borlama işlemiyle, yaklaşık olarak 43-60 µm arasındaki kalınlıklarda tek fazlı (Fe 2 B) bor tabakaları elde edilmiştir. Borlama işlemi ile döküm yapısına göre yaklaşık 3 kat, temper martensitik matris yapısına göre ise 2 kat daha fazla aşınma direnci elde edilmiştir.