Kaushik Nayak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Kaushik Nayak has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Sankatali Venkateswarlu
IMEC, Leuven, Belgium
5 shared publications - Akhil Sudarsanan
Department of Electrical Engineering, IIT Hyderabad, Hyderabad, India
3 shared publications Oves Badami
Department of Electrical Engineering, IIT Hyderabad, Hyderabad, India
3 shared publications- Yerragudi Pullaiah
Electrical Engineering Department, Indian Institute of Technology Hyderabad, Hyderabad, India
3 shared publications - Kumar Prashant
Department of Electrical Engineering, IIT-Hyderabad, Hyderabad, India
2 shared publications Mohit Bajaj
Synopsys India Pvt. Ltd., Bengaluru, Karnataka, India
2 shared publications
Latest Publications
- 17 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (2) , 557-563
Investigation of X-Ray Irradiance Hardness and High Temperature Operation of H-Terminated Diamond MOSFET
In this work, we have investigated the ionizing radiation X-ray hardness of H-terminated diamond MOSFET using TCAD-based device analysis. The radiation effect is captured via the trapped charges in bulk Al2O3 and interface traps at diamond/Al2O3 interface due to the generation of electron–hole pairs (EHPs). The simulated transfer characteristics of irradiated devices are calibrated against experimental data present in the literature. We further estimated the trapped charge density in gate oxide for different radiation doses and its effect on EHPs generation rate. In addition, typical device characteristic parameters, such as ${V}_{T}$ , ${J}_{\text {ON}}$ , ${J}_{\text {OFF}}$ , subthreshold swing (SS) and transconductance ( ${g}_{m}$ ) are analyzed for various radiation doses varying from 1 kGy to 10 MGy and across temperature (300–800 K). Diamond MOSFET exhibits a very high on-to-off current ratio both at room temperature and high temperatures with high radiation doses. Our study shows that relatively smaller variations in ${g}_{m}$ and SS for radiation dose higher than 10 kGy lead to radiation-hardened reliable transistor performance of the H-terminated diamond MOSFET.
- 17 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (2) , 557-563
Investigation of X-Ray Irradiance Hardness and High Temperature Operation of H-Terminated Diamond MOSFET
In this work, we have investigated the ionizing radiation X-ray hardness of H-terminated diamond MOSFET using TCAD-based device analysis. The radiation effect is captured via the trapped charges in bulk Al2O3 and interface traps at diamond/Al2O3 interface due to the generation of electron–hole pairs (EHPs). The simulated transfer characteristics of irradiated devices are calibrated against experimental data present in the literature. We further estimated the trapped charge density in gate oxide for different radiation doses and its effect on EHPs generation rate. In addition, typical device characteristic parameters, such as ${V}_{T}$ , ${J}_{\text {ON}}$ , ${J}_{\text {OFF}}$ , subthreshold swing (SS) and transconductance ( ${g}_{m}$ ) are analyzed for various radiation doses varying from 1 kGy to 10 MGy and across temperature (300–800 K). Diamond MOSFET exhibits a very high on-to-off current ratio both at room temperature and high temperatures with high radiation doses. Our study shows that relatively smaller variations in ${g}_{m}$ and SS for radiation dose higher than 10 kGy lead to radiation-hardened reliable transistor performance of the H-terminated diamond MOSFET.
- 3 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (7) , 1137-1140
Contact Analysis of Elemental Transition Metal Electrodes for Complementary 2D-FET Applications Using MoS2 and WSe2
First principle calculations for efficient transition metal contacts with monolayer MoS2-WSe2 are carried out for complementary device application. The four parameters analysed are exchange energy, density of states, entropy measurements, and effective potential periodicity at interface. Each characterises the electrical contact, as exchange energy establishes stable interface with minimum energy (contacts with strong bonding); density of states determines the charge polarity selection (electron or hole transport) and carrier flow rate through interfaces; entropy measurement reveal contacts with minimum phonon scattering rate (enhanced mobility); and effective potential continuity provides an alternative view of contact resistance from quantum mechanical perspective. Combining these results reveal that in specific crystallographic orientation among the 3d group: V, Cr, Co, and Ni; from 4d group: Tc, Ru, Pd, Ag and from 5d group: Ir, Pt, Au form suitable elemental electrodes for MoS2-WSe2 complementary FET applications.
- 3 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (7) , 1137-1140
Contact Analysis of Elemental Transition Metal Electrodes for Complementary 2D-FET Applications Using MoS2 and WSe2
First principle calculations for efficient transition metal contacts with monolayer MoS2-WSe2 are carried out for complementary device application. The four parameters analysed are exchange energy, density of states, entropy measurements, and effective potential periodicity at interface. Each characterises the electrical contact, as exchange energy establishes stable interface with minimum energy (contacts with strong bonding); density of states determines the charge polarity selection (electron or hole transport) and carrier flow rate through interfaces; entropy measurement reveal contacts with minimum phonon scattering rate (enhanced mobility); and effective potential continuity provides an alternative view of contact resistance from quantum mechanical perspective. Combining these results reveal that in specific crystallographic orientation among the 3d group: V, Cr, Co, and Ni; from 4d group: Tc, Ru, Pd, Ag and from 5d group: Ir, Pt, Au form suitable elemental electrodes for MoS2-WSe2 complementary FET applications.
- 2 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (1) , 271-277
TCAD Analysis of O-Terminated Diamond m-i-p+ Diode Characteristics Dependencies on Surface States CNL and Metal-Induced Gap States
In this article, a 2-D TCAD simulation study on the forward and reverse characteristics of oxygen-terminated diamond (D:O) m-i-p + Schottky barrier diode (SBD) is carried out considering the effects of Fermi level pinning due to surface states (SSs) and metal-induced gap states (MIGS). The device simulation considers drift-diffusion transport, SS charge neutrality level (CNL), MIGS through Fermi level pinning parameter ( ${S}$ ), doping and temperature-dependent mobility model, incomplete ionization of dopants, and impact ionization models. The simulation validation is carried out for Al/Au Schottky metals at room temperature and at higher temperatures. A good comparison between the simulation and experiment is obtained around turn-on voltage ( ${V}_{T{0}}~\sim ~1.0$ V for Al and ~2.0 V for Au Schottky contacts) and for anode voltage ( ${V}_{A}{)} > {V}_{T{0}}$ . Through simulations, we estimated the type of SSs and their quantity, and the position of CNL ( ${E}_{\text {CNL}}$ ) within the diamond bandgap. The effect of ${E}_{\text {CNL}}$ position and pinning parameter on the forward and reverse characteristics is also simulated. The impact of ${E}_{\text {CNL}}$ and SS on reverse leakage current is also analyzed using a nonlocal barrier tunneling model. At higher temperatures, a good match between simulation and experiment of forward characteristics is achieved.
- 2 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (1) , 271-277
TCAD Analysis of O-Terminated Diamond m-i-p+ Diode Characteristics Dependencies on Surface States CNL and Metal-Induced Gap States
In this article, a 2-D TCAD simulation study on the forward and reverse characteristics of oxygen-terminated diamond (D:O) m-i-p + Schottky barrier diode (SBD) is carried out considering the effects of Fermi level pinning due to surface states (SSs) and metal-induced gap states (MIGS). The device simulation considers drift-diffusion transport, SS charge neutrality level (CNL), MIGS through Fermi level pinning parameter ( ${S}$ ), doping and temperature-dependent mobility model, incomplete ionization of dopants, and impact ionization models. The simulation validation is carried out for Al/Au Schottky metals at room temperature and at higher temperatures. A good comparison between the simulation and experiment is obtained around turn-on voltage ( ${V}_{T{0}}~\sim ~1.0$ V for Al and ~2.0 V for Au Schottky contacts) and for anode voltage ( ${V}_{A}{)} > {V}_{T{0}}$ . Through simulations, we estimated the type of SSs and their quantity, and the position of CNL ( ${E}_{\text {CNL}}$ ) within the diamond bandgap. The effect of ${E}_{\text {CNL}}$ position and pinning parameter on the forward and reverse characteristics is also simulated. The impact of ${E}_{\text {CNL}}$ and SS on reverse leakage current is also analyzed using a nonlocal barrier tunneling model. At higher temperatures, a good match between simulation and experiment of forward characteristics is achieved.
- 21 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 42 (12) , 1878-1881
Electrode Orientation Dependent Transition Metal—(MoS₂; WS₂) Contact Analysis for 2D Material Based FET Applications
A Density Functional Theory based simulation study on cubic crystal orientation dependent transition metal contact with monolayer MoS 2 /WS 2 in reference to exchange energy, density of states and thermodynamic entropy measurements are studied. Exchange energy states the stability of the interfaces between MoS 2 /WS 2 and transition metals. The density of states calculation reveals the transport dominance with respect to charge polarity (electron or hole) and magnitude of charge flow through the interface. Entropy gives an alternative view to analyse carrier-phonon scattering at the interface. Our calculations suggest that (100) and (111) orientated transition metals from 3d group like Sc, Ti, Cr, Co, and Ni, (110) orientated transition metals from 4d group like Tc, Pd, Zr, and Ag and from 5d group (100), (110) orientated elements like Ta, W, Os, Ir, Pt are better suited for elemental contact applications in MoS 2 and WS 2 channel-based CMOS logic FETs.
- 21 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 42 (12) , 1878-1881
Electrode Orientation Dependent Transition Metal—(MoS₂; WS₂) Contact Analysis for 2D Material Based FET Applications
A Density Functional Theory based simulation study on cubic crystal orientation dependent transition metal contact with monolayer MoS 2 /WS 2 in reference to exchange energy, density of states and thermodynamic entropy measurements are studied. Exchange energy states the stability of the interfaces between MoS 2 /WS 2 and transition metals. The density of states calculation reveals the transport dominance with respect to charge polarity (electron or hole) and magnitude of charge flow through the interface. Entropy gives an alternative view to analyse carrier-phonon scattering at the interface. Our calculations suggest that (100) and (111) orientated transition metals from 3d group like Sc, Ti, Cr, Co, and Ni, (110) orientated transition metals from 4d group like Tc, Pd, Zr, and Ag and from 5d group (100), (110) orientated elements like Ta, W, Os, Ir, Pt are better suited for elemental contact applications in MoS 2 and WS 2 channel-based CMOS logic FETs.
- 19 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (9) , 4723-4728
Electro-Thermal Performance Boosting in Stacked Si Gate-all-Around Nanosheet FET With Engineered Source/Drain Contacts
In this article, we investigate the electro-thermal (ET) performance of stacked Si gate-all-around (GAA) nanosheet FET (NSHFET) by adopting the metal (M0) source/drain (S/D) engineered contacts such as M0-wrap around the Si S/D epitaxial regions and M0 filling through S/D trenched regions in addition to the conventional scheme where metal (M0) epi on the S/D. The device ET performance is enhanced by increasing the device on-state current (I ON ) by more than 10% with better device lattice heat removal from the hot-spot location of the NSHFET. This results in decreased device self-heating by lowering lattice hot-spot temperature (T L, max ) and device effective thermal resistance (R th, eff ) by more than 11% compared to conventional M0-epi-based NSHFET design. The junction temperature difference between the nanosheet channels is also lowered, which decreases the inter-sheet threshold voltage (V T ) difference. The benchmarking study of the device designs reveals that M0-trench-based NSHFET gives the best performance from both electrical and thermal perspective for future sub-5-nm CMOS logic technologies.
- 19 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (9) , 4723-4728
Electro-Thermal Performance Boosting in Stacked Si Gate-all-Around Nanosheet FET With Engineered Source/Drain Contacts
In this article, we investigate the electro-thermal (ET) performance of stacked Si gate-all-around (GAA) nanosheet FET (NSHFET) by adopting the metal (M0) source/drain (S/D) engineered contacts such as M0-wrap around the Si S/D epitaxial regions and M0 filling through S/D trenched regions in addition to the conventional scheme where metal (M0) epi on the S/D. The device ET performance is enhanced by increasing the device on-state current (I ON ) by more than 10% with better device lattice heat removal from the hot-spot location of the NSHFET. This results in decreased device self-heating by lowering lattice hot-spot temperature (T L, max ) and device effective thermal resistance (R th, eff ) by more than 11% compared to conventional M0-epi-based NSHFET design. The junction temperature difference between the nanosheet channels is also lowered, which decreases the inter-sheet threshold voltage (V T ) difference. The benchmarking study of the device designs reveals that M0-trench-based NSHFET gives the best performance from both electrical and thermal perspective for future sub-5-nm CMOS logic technologies.
- 3 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (6) , 2611-2617
TCAD-Based Investigation of Statistical Variability Immunity in U-Channel FDSOI n-MOSFET for Sub-7-nm Technology
In this article, the impact of random fluctuation sources, such as metal gate granularity (MGG), line edge roughness (LER), and random dopant fluctuations (RDFs), are numerically studied for U-shaped n-channel fully depleted silicon on insulator (FDSOI) MOSFET (U-SOIFET) over conventional n-channel FDSOI MOSFET (C-SOIFET) for 7-nm technology node. This article reports that improved short-channel effect immunity in U-SOIFET results in less 1σ threshold voltage ( V T ) and ON-current ( I ON ) fluctuations compared to C-SOIFET due to MGG and LER variability sources. U-SOIFET exhibits a low V T mismatch index ( A ΔVT =1.78 mV. μm) close to the literature reported. Due to combined variability sources, U-SOIFET shows less V T , I ON , subthreshold swing (SS), and DIBL fluctuations compared to C-SOIFET. Immunity to statistical variability sources makes U-SOIFET a suitable silicon on insulator (SOI) device architecture for future CMOS logic device applications.
- 3 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (6) , 2611-2617
TCAD-Based Investigation of Statistical Variability Immunity in U-Channel FDSOI n-MOSFET for Sub-7-nm Technology
In this article, the impact of random fluctuation sources, such as metal gate granularity (MGG), line edge roughness (LER), and random dopant fluctuations (RDFs), are numerically studied for U-shaped n-channel fully depleted silicon on insulator (FDSOI) MOSFET (U-SOIFET) over conventional n-channel FDSOI MOSFET (C-SOIFET) for 7-nm technology node. This article reports that improved short-channel effect immunity in U-SOIFET results in less 1σ threshold voltage ( V T ) and ON-current ( I ON ) fluctuations compared to C-SOIFET due to MGG and LER variability sources. U-SOIFET exhibits a low V T mismatch index ( A ΔVT =1.78 mV. μm) close to the literature reported. Due to combined variability sources, U-SOIFET shows less V T , I ON , subthreshold swing (SS), and DIBL fluctuations compared to C-SOIFET. Immunity to statistical variability sources makes U-SOIFET a suitable silicon on insulator (SOI) device architecture for future CMOS logic device applications.
- 3 April 2021
- Published by Springer Nature in Journal of Computational Electronics
- Vol. 20 (3) , 1169-1177
Immunity to random fluctuations induced by interface trap variability in Si gate-all-around n-nanowire field-effect transistor devices
- 3 April 2021
- Published by Springer Nature in Journal of Computational Electronics
- Vol. 20 (3) , 1169-1177
Immunity to random fluctuations induced by interface trap variability in Si gate-all-around n-nanowire field-effect transistor devices
- 27 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (10) , 4493-4499
Hetero-Interfacial Thermal Resistance Effects on Device Performance of Stacked Gate-All-Around Nanosheet FET
This article reports that Hetero-interfacial-thermal resistance (HITR) due to phonon scattering and weak electron-phonon coupling at hetero-interfaces, can impact stacked Si gate-all-around (GAA) nanosheet field effect transistor (NSHFET) self-heating effect (SHE) and reliability. We have investigated the HITR of Si/SiO₂ and Si/metal-silicides on SHE of vertically stacked Si GAA NSHFET. Our simulation predictions reveal that a very noticeable effect of the HITR of Si/M0 at front end of line (FEOL) and back end of line (BEOL) interface (FEOL/BEOL) is that the hot-spot location is shifted into the channel away from drain depletion region, which affects the device SHE and degrades device performance. The impact of nanosheet width (WNSH) and sheets stacking number (N) on device SHE and drive current degradation with and without HITR effect are also studied. It is revealed that wider nanosheets with lower HITR can be a better device design choice for heat mitigation in high performance logic transistors.
- 27 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (10) , 4493-4499
Hetero-Interfacial Thermal Resistance Effects on Device Performance of Stacked Gate-All-Around Nanosheet FET
This article reports that Hetero-interfacial-thermal resistance (HITR) due to phonon scattering and weak electron-phonon coupling at hetero-interfaces, can impact stacked Si gate-all-around (GAA) nanosheet field effect transistor (NSHFET) self-heating effect (SHE) and reliability. We have investigated the HITR of Si/SiO₂ and Si/metal-silicides on SHE of vertically stacked Si GAA NSHFET. Our simulation predictions reveal that a very noticeable effect of the HITR of Si/M0 at front end of line (FEOL) and back end of line (BEOL) interface (FEOL/BEOL) is that the hot-spot location is shifted into the channel away from drain depletion region, which affects the device SHE and degrades device performance. The impact of nanosheet width (WNSH) and sheets stacking number (N) on device SHE and drive current degradation with and without HITR effect are also studied. It is revealed that wider nanosheets with lower HITR can be a better device design choice for heat mitigation in high performance logic transistors.
- Open Access
- 15 April 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 127 (15) , 153102
Enhancement of the optical gain in GaAs nanocylinders for nanophotonic applications
Semiconductor nanolasers based on microdisks, photonic crystal cavities, and metallo-dielectric nanocavities have been studied during the last few decades for on-chip light source applications. However, practical realization of low threshold, room temperature semiconductor nanolasers is still a challenge due to the large surface-to-volume ratio of the nanostructures, which results in low optical gain and hence higher lasing threshold. Furthermore, the gain in nanostructures is an important parameter for designing all-dielectric metamaterial-based active applications. Here, we investigate the impact of p-type doping, compressive strain, and surface recombination on the gain spectrum and the spatial distribution of carriers in GaAs nanocylinders. Our analysis reveals that the lasing threshold can be lowered by choosing the right doping concentration in the active III–V material combined with compressive strain. This combination of strain and p-type doping shows 100× improvement in gain and approximately five times increase in modulation bandwidth for high-speed operation.
- 15 April 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 127 (15) , 153102
Open AccessEnhancement of the optical gain in GaAs nanocylinders for nanophotonic applications
Semiconductor nanolasers based on microdisks, photonic crystal cavities, and metallo-dielectric nanocavities have been studied during the last few decades for on-chip light source applications. However, practical realization of low threshold, room temperature semiconductor nanolasers is still a challenge due to the large surface-to-volume ratio of the nanostructures, which results in low optical gain and hence higher lasing threshold. Furthermore, the gain in nanostructures is an important parameter for designing all-dielectric metamaterial-based active applications. Here, we investigate the impact of p-type doping, compressive strain, and surface recombination on the gain spectrum and the spatial distribution of carriers in GaAs nanocylinders. Our analysis reveals that the lasing threshold can be lowered by choosing the right doping concentration in the active III–V material combined with compressive strain. This combination of strain and p-type doping shows 100× improvement in gain and approximately five times increase in modulation bandwidth for high-speed operation.
- 5 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (4) , 1530-1536
Ambient Temperature-Induced Device Self-Heating Effects on Multi-Fin Si CMOS Logic Circuit Performance in N-14 to N-7 Scaled Technologies
We have studied the impact of thermal contact resistance (TCR) (Rth) and within-chip ambient temperature (TA) on the device self-heating effect (SHE) and its effect on transient and steady-state performance of Si 3-Fin FinFET-based CMOS inverter (from N-14 to N-7 technologies) using coupled hydrodynamic-thermodynamic (HD-TH) mixed-mode simulations. The effect of the load capacitance (CL) on device lattice temperature (TL) and its impact on propagation delay (tpd) of the targeted CMOS inverter circuit are analyzed. The impact of technology scaling on SHE of inverter and its effect on circuit performance is also studied. We investigated the SHE in the 3-Fin FinFET-based ring oscillator (RO) and estimated the stage delay and frequency of oscillations. Our simulation results revealed that within-chip TA and Rth of gate, source, and drain (Rth,GSD) have significant effect on the logic circuit performance in terms of degradation of noise margin (NM), inverter gain (| gmax|), and increase in tpd due to SHE from N-14 to N-7 technologies.
- 5 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (4) , 1530-1536
Ambient Temperature-Induced Device Self-Heating Effects on Multi-Fin Si CMOS Logic Circuit Performance in N-14 to N-7 Scaled Technologies
We have studied the impact of thermal contact resistance (TCR) (Rth) and within-chip ambient temperature (TA) on the device self-heating effect (SHE) and its effect on transient and steady-state performance of Si 3-Fin FinFET-based CMOS inverter (from N-14 to N-7 technologies) using coupled hydrodynamic-thermodynamic (HD-TH) mixed-mode simulations. The effect of the load capacitance (CL) on device lattice temperature (TL) and its impact on propagation delay (tpd) of the targeted CMOS inverter circuit are analyzed. The impact of technology scaling on SHE of inverter and its effect on circuit performance is also studied. We investigated the SHE in the 3-Fin FinFET-based ring oscillator (RO) and estimated the stage delay and frequency of oscillations. Our simulation results revealed that within-chip TA and Rth of gate, source, and drain (Rth,GSD) have significant effect on the logic circuit performance in terms of degradation of noise margin (NM), inverter gain (| gmax|), and increase in tpd due to SHE from N-14 to N-7 technologies.