Baiwei Lei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Baiwei Lei has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
Bing Wu
School of Emergency Management and Safety Engineering
12 shared publicationsBinbin He
6 shared publications- Bing Wu
School of Emergency Management and Safety Engineering, China University of Mining and Technology (Beijing), Beijing, China
5 shared publications Zhiyan Zhao
5 shared publications- Chao Li4 shared publications
Chenguang Zhao
School of Emergency Management and Safety Engineering, China University of Mining & Technology (Beijing), Beijing, China
4 shared publications
Latest Publications
- 12 September 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 275
Influence of tunnel slope on hydrogen transport–dispersion characteristics and subsequent explosion consequences
- 12 September 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 275
Influence of tunnel slope on hydrogen transport–dispersion characteristics and subsequent explosion consequences
- 23 December 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (1) , 53-76
Review and Perspectives of Gas-Explosion Flame Propagation in Porous Media
- 23 December 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (1) , 53-76
Review and Perspectives of Gas-Explosion Flame Propagation in Porous Media
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Experimental study on the effects of inert gases on methane explosion characteristics in a loose medium environment
Gas explosion accidents are one of the major disasters threatening mine safety. The goaf areas in coal mines consist of loose media composed of fragmented coal and rock. Their strong concealment and destructive potential make the prevention and control of gas explosion accidents particularly challenging. In this paper, controlled experiments on methane explosions in loose media were conducted to investigate the variation of explosion characteristics under different inert gas environments, and to discuss the coupling mechanism by which inert gases and loose media influence methane explosion reactions. The results indicate that as the gas concentration increases, both the peak explosion overpressure and the maximum pressure rise rate of methane explosions in loose media tend to decrease. At the same concentration, CO2 is more effective than N2 in suppressing methane explosions in loose media. The maximum difference between the suppression rates of explosion overpressure by CO2 and N2 is 25.36%, with a maximum difference of 9.89% observed in the loose media. When the porosities are 0.504 and 0.534, the combined suppression effect of inert gases and loose media on methane explosion characteristics is better than that of either factor alone. At a porosity of 0.602, the promoting effect of loose media on methane explosions becomes more pronounced; however, as the concentration of inert gases increases, this promoting effect is significantly weakened. Moreover, with increasing inert gas concentration, the KG value of methane explosions in loose media shows a decreasing trend. When the porosities are 0.504 and 0.534, the KG value in loose media is only 3.27%–29.71% of that in a cavity, while at a porosity of 0.602, the KG value increases significantly to approximately 105.65%–450.03% of that in a cavity. N2 at concentrations of 5% and 10% has little effect on the KG value, whereas both N2 and CO2 at a concentration of 15% exhibit good explosion suppression effects. This work provides a theoretical basis for the formulation of prevention and control measures for gas explosion accidents in coal mine goaf areas.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Experimental study on the effects of inert gases on methane explosion characteristics in a loose medium environment
Gas explosion accidents are one of the major disasters threatening mine safety. The goaf areas in coal mines consist of loose media composed of fragmented coal and rock. Their strong concealment and destructive potential make the prevention and control of gas explosion accidents particularly challenging. In this paper, controlled experiments on methane explosions in loose media were conducted to investigate the variation of explosion characteristics under different inert gas environments, and to discuss the coupling mechanism by which inert gases and loose media influence methane explosion reactions. The results indicate that as the gas concentration increases, both the peak explosion overpressure and the maximum pressure rise rate of methane explosions in loose media tend to decrease. At the same concentration, CO2 is more effective than N2 in suppressing methane explosions in loose media. The maximum difference between the suppression rates of explosion overpressure by CO2 and N2 is 25.36%, with a maximum difference of 9.89% observed in the loose media. When the porosities are 0.504 and 0.534, the combined suppression effect of inert gases and loose media on methane explosion characteristics is better than that of either factor alone. At a porosity of 0.602, the promoting effect of loose media on methane explosions becomes more pronounced; however, as the concentration of inert gases increases, this promoting effect is significantly weakened. Moreover, with increasing inert gas concentration, the KG value of methane explosions in loose media shows a decreasing trend. When the porosities are 0.504 and 0.534, the KG value in loose media is only 3.27%–29.71% of that in a cavity, while at a porosity of 0.602, the KG value increases significantly to approximately 105.65%–450.03% of that in a cavity. N2 at concentrations of 5% and 10% has little effect on the KG value, whereas both N2 and CO2 at a concentration of 15% exhibit good explosion suppression effects. This work provides a theoretical basis for the formulation of prevention and control measures for gas explosion accidents in coal mine goaf areas.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Experimental study on CH4/air premixed gas explosion in loose media
The goaf in coal mines is composed of loose media formed by fragmented coal and rock, and the explosion characteristics of gas within such loose media differ significantly from those in free spaces. In this paper, methane explosion experiments in loose media were conducted to investigate the influence of porosity on the explosion characteristics of methane. The results indicate that under the current conditions, the inhibition rate of explosion pressure and pressure rise rate by the porosity of the loose media generally follow an exponential decay trend. At a porosity of approximately 0.567, the loose media changes from inhibiting to promoting the pressure rise rate generated by the explosion. At a porosity of approximately 0.613, the loose media shifts from inhibiting to promoting the explosion pressure of methane, and the exponential decay relationship between pressure decay rate and porosity may be disrupted. Heat loss and turbulent disturbances are important factors affecting the explosion characteristics of methane in loose media. When the effect of heat loss exceeds that of turbulence disturbances, the loose media significantly suppress the methane explosion; compared to methane explosions in a cavity, the overpressure peak is reduced by 81.82% –93.14%. Conversely, when turbulent disturbances are the primary influencing factor, the loose media can promote the methane explosion reaction process; in loose media with a porosity of 0.602, the maximum rate of pressure rise of the methane explosion is 134.96% higher than that in a cavity, and the deflagration index is 99.43% higher.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Experimental study on CH4/air premixed gas explosion in loose media
The goaf in coal mines is composed of loose media formed by fragmented coal and rock, and the explosion characteristics of gas within such loose media differ significantly from those in free spaces. In this paper, methane explosion experiments in loose media were conducted to investigate the influence of porosity on the explosion characteristics of methane. The results indicate that under the current conditions, the inhibition rate of explosion pressure and pressure rise rate by the porosity of the loose media generally follow an exponential decay trend. At a porosity of approximately 0.567, the loose media changes from inhibiting to promoting the pressure rise rate generated by the explosion. At a porosity of approximately 0.613, the loose media shifts from inhibiting to promoting the explosion pressure of methane, and the exponential decay relationship between pressure decay rate and porosity may be disrupted. Heat loss and turbulent disturbances are important factors affecting the explosion characteristics of methane in loose media. When the effect of heat loss exceeds that of turbulence disturbances, the loose media significantly suppress the methane explosion; compared to methane explosions in a cavity, the overpressure peak is reduced by 81.82% –93.14%. Conversely, when turbulent disturbances are the primary influencing factor, the loose media can promote the methane explosion reaction process; in loose media with a porosity of 0.602, the maximum rate of pressure rise of the methane explosion is 134.96% higher than that in a cavity, and the deflagration index is 99.43% higher.
- 1 June 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (6)
Impact of inflation pressure on blast-resistant mechanical response and cushioning of sealed airbags
The sealing technology in tunnels can effectively curb the spread of the mine fires; however, the risk of gas explosions remains high during the sealing process. As an important method for tunnel sealing, rapid airbag sealing technology has made significant progress. Nevertheless, research on its response to explosion-induced shock waves remains insufficient. Therefore, experimental and numerical investigations into the blast-resistant cushioning of sealed airbags were performed with different initial inflation pressures. The results indicate that shock waves do not transmit through the airbag, and sealed airbags under different inflation pressures exhibit varying degrees of cushioning performance, with a maximum cushioning effect of 28.5% under experimental conditions. When subjected to shock waves, the airbag undergoes axial compression along the pipeline. Excessively high or low inflation pressure can lead to large-scale localized stress concentrations. In the energy evolution of the airbag, the increase in the internal energy of the gas inside the airbag accounts for approximately 62%–76% of the total energy absorption. Furthermore, changes in the airbag's internal energy result in an optimal energy absorption inflection point exceeding standard atmospheric pressure, and the reflected energy increases with higher initial inflation pressure. Under full-scale simulation conditions, the optimal cushioning effect was achieved when the inflation pressure was 25 kPa overpressure. The research results provide theoretical support for the structural optimization design and selection of optimal working parameters for blast-resistant airbags.
- 1 June 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (6)
Impact of inflation pressure on blast-resistant mechanical response and cushioning of sealed airbags
The sealing technology in tunnels can effectively curb the spread of the mine fires; however, the risk of gas explosions remains high during the sealing process. As an important method for tunnel sealing, rapid airbag sealing technology has made significant progress. Nevertheless, research on its response to explosion-induced shock waves remains insufficient. Therefore, experimental and numerical investigations into the blast-resistant cushioning of sealed airbags were performed with different initial inflation pressures. The results indicate that shock waves do not transmit through the airbag, and sealed airbags under different inflation pressures exhibit varying degrees of cushioning performance, with a maximum cushioning effect of 28.5% under experimental conditions. When subjected to shock waves, the airbag undergoes axial compression along the pipeline. Excessively high or low inflation pressure can lead to large-scale localized stress concentrations. In the energy evolution of the airbag, the increase in the internal energy of the gas inside the airbag accounts for approximately 62%–76% of the total energy absorption. Furthermore, changes in the airbag's internal energy result in an optimal energy absorption inflection point exceeding standard atmospheric pressure, and the reflected energy increases with higher initial inflation pressure. Under full-scale simulation conditions, the optimal cushioning effect was achieved when the inflation pressure was 25 kPa overpressure. The research results provide theoretical support for the structural optimization design and selection of optimal working parameters for blast-resistant airbags.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Evaluation of unconfined hydrogen deflagration characteristics under different turbulence and combustion models: The influence of barrier wall position
Hydrogen poses a significant risk of explosion, particularly in open spaces. To mitigate the risk of hydrogen explosions, barrier walls are commonly used as a protective measure in practical engineering. However, due to the high cost of experimentation and limitations in monitoring methods, computational fluid dynamics (CFD) simulations play a crucial role in combustion dynamics research. To ensure the accuracy and reliability of CFD simulation results, it is essential to select appropriate combustion and turbulence models. This paper evaluated the applicability of seven combustion models, seven correlations of turbulent flame speed models, and three turbulence models in simulating hydrogen deflagration in open spaces based on GASFLOW-Multi-Physics-Integration. The results showed that the modified multi-phenomenon turbulent burning velocity model, the Schmidt correlation model, and the detached eddy simulation turbulence model provided high computational accuracy in predicting hydrogen deflagration behavior. Additionally, it was found that in open spaces, Darrieus-Landau instability inhibited flame propagation, while flame stretch and thermal-diffusive instability significantly accelerated it. The study further analyzed the hydrogen deflagration characteristics at different barrier wall positions, revealing that while placing the barrier walls closer to the ignition source significantly reduced the explosion hazard in the rear area, it simultaneously increased the damage in the front area. Additionally, the effective protective range of the barrier wall was dependent on its distance from the ignition source. As the distance between the barrier wall and the ignition source increased, its ability to attenuate the blast wave gradually decreased, leading to a reduction in the effective protective range.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Evaluation of unconfined hydrogen deflagration characteristics under different turbulence and combustion models: The influence of barrier wall position
Hydrogen poses a significant risk of explosion, particularly in open spaces. To mitigate the risk of hydrogen explosions, barrier walls are commonly used as a protective measure in practical engineering. However, due to the high cost of experimentation and limitations in monitoring methods, computational fluid dynamics (CFD) simulations play a crucial role in combustion dynamics research. To ensure the accuracy and reliability of CFD simulation results, it is essential to select appropriate combustion and turbulence models. This paper evaluated the applicability of seven combustion models, seven correlations of turbulent flame speed models, and three turbulence models in simulating hydrogen deflagration in open spaces based on GASFLOW-Multi-Physics-Integration. The results showed that the modified multi-phenomenon turbulent burning velocity model, the Schmidt correlation model, and the detached eddy simulation turbulence model provided high computational accuracy in predicting hydrogen deflagration behavior. Additionally, it was found that in open spaces, Darrieus-Landau instability inhibited flame propagation, while flame stretch and thermal-diffusive instability significantly accelerated it. The study further analyzed the hydrogen deflagration characteristics at different barrier wall positions, revealing that while placing the barrier walls closer to the ignition source significantly reduced the explosion hazard in the rear area, it simultaneously increased the damage in the front area. Additionally, the effective protective range of the barrier wall was dependent on its distance from the ignition source. As the distance between the barrier wall and the ignition source increased, its ability to attenuate the blast wave gradually decreased, leading to a reduction in the effective protective range.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
Mechanical response characteristics and cushioning of sealed airbags under different length–diameter ratios
In the event of a mine fire, rapidly constructing blast-resistant seals is one of the most effective measures to contain the disaster. This study conducted blast cushioning experiments on sealed airbags and numerical simulations by analysis system/Livermore software-dynamics (ANSYS/LS-DYNA), an explicit simulation software, to analyze the mechanical response characteristics and cushioning effectiveness of sealed airbags under different length-to-diameter ratios. The research results indicate that airbags with different length-to-diameter ratios all exhibit cushioning effects, and the airbag can recover its deformation after pressure release. As airbag length increases, vertical deformation along the pipeline appears, forming a radial compression failure mode. Stress concentrations are mostly located at the edges of the airbag, while arched structures can reduce the concentrated stress. Excessively long or short airbags significantly increase localized stress concentrations. The total energy absorbed by the airbag during cushioning shows a linear relationship with its length, and an energy absorption model for single-chamber airbags with varying length-to-diameter ratios was established. Under full-scale simulation conditions, the optimal length-to-diameter ratio range is 0.75:1. The reflected energy of shockwave encountering airbag is independent of airbag length and remains a fixed value when inflation pressure remains constant. These findings provide theoretical support for the design and application of explosion-resistant airbag.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
Mechanical response characteristics and cushioning of sealed airbags under different length–diameter ratios
In the event of a mine fire, rapidly constructing blast-resistant seals is one of the most effective measures to contain the disaster. This study conducted blast cushioning experiments on sealed airbags and numerical simulations by analysis system/Livermore software-dynamics (ANSYS/LS-DYNA), an explicit simulation software, to analyze the mechanical response characteristics and cushioning effectiveness of sealed airbags under different length-to-diameter ratios. The research results indicate that airbags with different length-to-diameter ratios all exhibit cushioning effects, and the airbag can recover its deformation after pressure release. As airbag length increases, vertical deformation along the pipeline appears, forming a radial compression failure mode. Stress concentrations are mostly located at the edges of the airbag, while arched structures can reduce the concentrated stress. Excessively long or short airbags significantly increase localized stress concentrations. The total energy absorbed by the airbag during cushioning shows a linear relationship with its length, and an energy absorption model for single-chamber airbags with varying length-to-diameter ratios was established. Under full-scale simulation conditions, the optimal length-to-diameter ratio range is 0.75:1. The reflected energy of shockwave encountering airbag is independent of airbag length and remains a fixed value when inflation pressure remains constant. These findings provide theoretical support for the design and application of explosion-resistant airbag.