Yasuharu Kanda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yasuharu Kanda has a total of 88 co-authors. Here are the top co-authors by number of shared publications:
Yoshio Uemichi
Professor emeritus, Muroran Institute of Technology
20 shared publicationsMasatoshi Sugioka
14 shared publications- Ken-Ichi Shimizu
Hokkaido University N-21, W-10
8 shared publications Takao Kobayashi
Technical Division, Muroran Institute of Technology
7 shared publications- Takashi Toyao
Hokkaido University N-21, W-10
7 shared publications Ayaka Sawada
5 shared publications
Latest Publications
- 6 February 2024
- Published by Wiley in Chemistry – An Asian Journal
- Vol. 19 (16) , e202301003
In Situ Spectroscopic Study of CO2 Capture and Methanation over Ni−Ca Based Dual Functional Materials
Carbon dioxide capture and reduction (CCR) to CH4 using dual‐functional materials (DFMs) have recently attracted significant attention as a promising strategy for carbon capture and utilization. In this study, we investigate the mechanism of CCR to CH4 over Al2O3‐supported Ni−Ca DFMs (Ni−Ca/Al2O3) under cyclic feeds of model combustion exhaust (2.5 % CO2+0 or 10 % O2/N2) and H2 at 500 °C. Various spectroscopic analyses, including time‐resolved in situ X‐ray diffraction and X‐ray absorption spectroscopy, were conducted during CO2 capture and the subsequent H2‐reduction steps. Based on these analyses, we propose a mechanism of CCR to CH4 over Ni−Ca based DFMs. During the CO2 capture step, the Ni0 species underwent complete oxidation in the presence of O2 to yield NiO. Subsequently, CO2 was captured through the interaction between the CaO surface and CO2, resulting in the formation of CaCO3 layers on the CaO particles. When the gas flow was switched to H2, NiO was partially to provide Ni0 sites, which acted as active sites for H2‐reduction of the adjacent CaCO3 layers to yield CaO and gas‐phase products, CH4 and H2O.
- 6 February 2024
- Published by Wiley in Chemistry – An Asian Journal
- Vol. 19 (16) , e202301003
In Situ Spectroscopic Study of CO2 Capture and Methanation over Ni−Ca Based Dual Functional Materials
Carbon dioxide capture and reduction (CCR) to CH4 using dual‐functional materials (DFMs) have recently attracted significant attention as a promising strategy for carbon capture and utilization. In this study, we investigate the mechanism of CCR to CH4 over Al2O3‐supported Ni−Ca DFMs (Ni−Ca/Al2O3) under cyclic feeds of model combustion exhaust (2.5 % CO2+0 or 10 % O2/N2) and H2 at 500 °C. Various spectroscopic analyses, including time‐resolved in situ X‐ray diffraction and X‐ray absorption spectroscopy, were conducted during CO2 capture and the subsequent H2‐reduction steps. Based on these analyses, we propose a mechanism of CCR to CH4 over Ni−Ca based DFMs. During the CO2 capture step, the Ni0 species underwent complete oxidation in the presence of O2 to yield NiO. Subsequently, CO2 was captured through the interaction between the CaO surface and CO2, resulting in the formation of CaCO3 layers on the CaO particles. When the gas flow was switched to H2, NiO was partially to provide Ni0 sites, which acted as active sites for H2‐reduction of the adjacent CaCO3 layers to yield CaO and gas‐phase products, CH4 and H2O.
- 20 September 2023
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 13 (21) , 6247-6253
Propane metathesis and hydrogenolysis over titanium hydride catalysts
Propane metathesis reactions over group 2–5 metal hydrides were investigated where TiH2 exhibited the highest butane formation amount. This study is the first example of carbon–carbon bond cleavage and formation over bulk metal hydrides.
- 20 September 2023
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 13 (21) , 6247-6253
Propane metathesis and hydrogenolysis over titanium hydride catalysts
Propane metathesis reactions over group 2–5 metal hydrides were investigated where TiH2 exhibited the highest butane formation amount. This study is the first example of carbon–carbon bond cleavage and formation over bulk metal hydrides.
- 5 May 2023
- Published by Oxford University Press (OUP) in Chemistry Letters
- Vol. 52 (5) , 310-313
Highly Active Ruthenium Phosphide Catalyst for Selective Hydrogenation of Acetylene and Its Reaction Mechanism
- 5 May 2023
- Published by Oxford University Press (OUP) in Chemistry Letters
- Vol. 52 (5) , 310-313
Highly Active Ruthenium Phosphide Catalyst for Selective Hydrogenation of Acetylene and Its Reaction Mechanism
- 1 September 2022
- Published by Japan Petroleum Institute in Journal of the Japan Petroleum Institute
- Vol. 65 (5) , 175-183
Highly Active Silica-supported Rhodium Phosphide Hydrodesulfurization Catalyst Prepared by Sequential Impregnation to Control the Rhodium and Phosphorus State
本研究では,RhとPの担持状態がP添加Rh触媒の水素化脱硫(HDS)活性に与える影響について検討した。調製した触媒は紫外可視拡散反射分光法(UV-Vis DRS),昇温還元(TPR),X線回折(XRD),CO吸着によりキャラクタリゼーションした。P/SiO2にRhを担持する逐次含浸法で調製したRh/P/SiO2触媒では,SiO2表面に担持されたリン酸種とRh種が相互作用することで,高分散なRh–リン酸錯体が生成することを明らかにした。Rh/SiO2にP源を担持したP/Rh/SiO2触媒では,表面がPで覆われたRh種が多く見られた。一方,共含浸法で調製したRh–P/SiO2触媒では,多核化が進行したRh錯体が生成した。XRDとCO吸着量から,Rh種の分散度はRh/P/SiO2 > P/Rh/SiO2 ≈ Rh–P/SiO2となることを明らかにした。600 ℃で還元した触媒のHDS活性はRh/P/SiO2 > P/Rh/SiO2 ≈ Rh–P/SiO2となった。Rh/P/SiO2触媒が最も高いHDS活性を示したのは,Pによる被覆がなくRh原子が表面に露出しているRh2Pが高分散に存在するためであると言える。
- 1 September 2022
- Published by Japan Petroleum Institute in Journal of the Japan Petroleum Institute
- Vol. 65 (5) , 175-183
Highly Active Silica-supported Rhodium Phosphide Hydrodesulfurization Catalyst Prepared by Sequential Impregnation to Control the Rhodium and Phosphorus State
本研究では,RhとPの担持状態がP添加Rh触媒の水素化脱硫(HDS)活性に与える影響について検討した。調製した触媒は紫外可視拡散反射分光法(UV-Vis DRS),昇温還元(TPR),X線回折(XRD),CO吸着によりキャラクタリゼーションした。P/SiO2にRhを担持する逐次含浸法で調製したRh/P/SiO2触媒では,SiO2表面に担持されたリン酸種とRh種が相互作用することで,高分散なRh–リン酸錯体が生成することを明らかにした。Rh/SiO2にP源を担持したP/Rh/SiO2触媒では,表面がPで覆われたRh種が多く見られた。一方,共含浸法で調製したRh–P/SiO2触媒では,多核化が進行したRh錯体が生成した。XRDとCO吸着量から,Rh種の分散度はRh/P/SiO2 > P/Rh/SiO2 ≈ Rh–P/SiO2となることを明らかにした。600 ℃で還元した触媒のHDS活性はRh/P/SiO2 > P/Rh/SiO2 ≈ Rh–P/SiO2となった。Rh/P/SiO2触媒が最も高いHDS活性を示したのは,Pによる被覆がなくRh原子が表面に露出しているRh2Pが高分散に存在するためであると言える。
- 8 March 2022
- Published by Elsevier in Journal of Catalysis
- Vol. 408, 294-302
Enhancement of the hydrodesulfurization and C−S bond cleavage activities of rhodium phosphide catalysts by platinum addition
- 8 March 2022
- Published by Elsevier in Journal of Catalysis
- Vol. 408, 294-302
Enhancement of the hydrodesulfurization and C−S bond cleavage activities of rhodium phosphide catalysts by platinum addition
- Open Access
- 25 February 2022
- Published by Elsevier in Chemosphere
- Vol. 297, 134057
Difference in cadmium chemisorption on calcite and vaterite porous particles
- 25 February 2022
- Published by Elsevier in Chemosphere
- Vol. 297, 134057
Open AccessDifference in cadmium chemisorption on calcite and vaterite porous particles
- Open Access
- 16 February 2022
- Published by Elsevier in SSRN Electronic Journal
Difference in Cadmium Chemisorption on Calcite and Vaterite Porous Particles
Cadmium is adsorbed on calcium carbonate via chemisorption. All calcium carbonate polymorphs generate otavite (cadmium carbonate), indicating that the crystallographic differences in calcium carbonate should affect the chemisorption equilibrium and kinetics. This study investigates the influences of the polymorph and specific surface area on cadmium adsorption. Here, we synthesise two polymorphs of porous calcium carbonate: calcite and vaterite with a wide range of specific surface areas. Then the equilibrium of cadmium adsorption is evaluated using adsorption isotherm models. Based on the Langmuir model with linear regression analysis, the maximum adsorptions of porous calcite and vaterite particles are 287.8 mg/g and 883.5 mg/g, respectively. The kinetics of cadmium chemisorption show clear differences between polymorphs. The calculated rate constant of the porous calcite particles using a pseudo-second-order reaction and Elovich models are two orders larger than that of porous vaterite particles. Although the adsorbed amount is superior for porous vaterite particles, porous calcite particles exhibit a faster reaction and relatively high adsorbed capacity for cadmium ions.
- 16 February 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessDifference in Cadmium Chemisorption on Calcite and Vaterite Porous Particles
Cadmium is adsorbed on calcium carbonate via chemisorption. All calcium carbonate polymorphs generate otavite (cadmium carbonate), indicating that the crystallographic differences in calcium carbonate should affect the chemisorption equilibrium and kinetics. This study investigates the influences of the polymorph and specific surface area on cadmium adsorption. Here, we synthesise two polymorphs of porous calcium carbonate: calcite and vaterite with a wide range of specific surface areas. Then the equilibrium of cadmium adsorption is evaluated using adsorption isotherm models. Based on the Langmuir model with linear regression analysis, the maximum adsorptions of porous calcite and vaterite particles are 287.8 mg/g and 883.5 mg/g, respectively. The kinetics of cadmium chemisorption show clear differences between polymorphs. The calculated rate constant of the porous calcite particles using a pseudo-second-order reaction and Elovich models are two orders larger than that of porous vaterite particles. Although the adsorbed amount is superior for porous vaterite particles, porous calcite particles exhibit a faster reaction and relatively high adsorbed capacity for cadmium ions.
- 7 December 2021
- Published by Oxford University Press (OUP) in Chemistry Letters
- Vol. 51 (1) , 88-90
Propane Dehydrogenation Catalysis of Titanium Hydrides: Positive Effect of Hydrogen Co-feeding
This study investigated the non-oxidative propane dehydrogenation over TiH2. It was found that H2 co-feeding positively affected dehydrogenation, improving the propylene formation rate. In situ spectroscopic characterization of TiH2 in the presence of H2 indicated that partially dehydrogenated titanium hydrides are active for dehydrogenation.
- 7 December 2021
- Published by Oxford University Press (OUP) in Chemistry Letters
- Vol. 51 (1) , 88-90
Propane Dehydrogenation Catalysis of Titanium Hydrides: Positive Effect of Hydrogen Co-feeding
This study investigated the non-oxidative propane dehydrogenation over TiH2. It was found that H2 co-feeding positively affected dehydrogenation, improving the propylene formation rate. In situ spectroscopic characterization of TiH2 in the presence of H2 indicated that partially dehydrogenated titanium hydrides are active for dehydrogenation.
- Open Access
In-Exchanged CHA Zeolites for Selective Dehydrogenation of Ethane: Characterization and Effect of Zeolite Framework Type
In this study, the characterization of In-exchanged CHA zeolite (In-CHA (SiO2/Al2O3 = 22.3)) was conducted by in-situ X-ray diffraction (XRD) and ammonia temperature-programmed desorption (NH3-TPD). We also prepared other In-exchanged zeolites with different zeolite structures (In-MFI (SiO2/Al2O3 = 22.3), In-MOR (SiO2/Al2O3 = 20), and In-BEA (SiO2/Al2O3 = 25)) and different SiO2/Al2O3 ratios (In-CHA(Al-rich) (SiO2/Al2O3 = 13.7)). Their catalytic activities in nonoxidative ethane dehydrogenation were compared. Among the tested catalysts, In-CHA(Al-rich) provided the highest conversion. From kinetic experiments and in-situ Fourier transform infrared (FTIR) spectroscopy, [InH2]+ ions are formed regardless of SiO2/Al2O3 ratio, serving as the active sites.
Open AccessIn-Exchanged CHA Zeolites for Selective Dehydrogenation of Ethane: Characterization and Effect of Zeolite Framework Type
In this study, the characterization of In-exchanged CHA zeolite (In-CHA (SiO2/Al2O3 = 22.3)) was conducted by in-situ X-ray diffraction (XRD) and ammonia temperature-programmed desorption (NH3-TPD). We also prepared other In-exchanged zeolites with different zeolite structures (In-MFI (SiO2/Al2O3 = 22.3), In-MOR (SiO2/Al2O3 = 20), and In-BEA (SiO2/Al2O3 = 25)) and different SiO2/Al2O3 ratios (In-CHA(Al-rich) (SiO2/Al2O3 = 13.7)). Their catalytic activities in nonoxidative ethane dehydrogenation were compared. Among the tested catalysts, In-CHA(Al-rich) provided the highest conversion. From kinetic experiments and in-situ Fourier transform infrared (FTIR) spectroscopy, [InH2]+ ions are formed regardless of SiO2/Al2O3 ratio, serving as the active sites.
- Open Access
- 1 May 2020
- Published by Japan Petroleum Institute in Journal of the Japan Petroleum Institute
- Vol. 63 (3) , 141-148
Sulfur Tolerance Properties of Rhodium Phosphide Evaluated by a New Temperature-programmed Sulfidation Technique
Sulfur tolerance properties of rhodium phosphide (Rh2P) were qualitatively and quantitatively evaluated by the temperature-programmed sulfidation (TPS) technique. The TPS profile of the Rh/SiO2 catalyst demonstrated a peak attributed to Rh2S3 formation around 400 °C. The TPS profiles of P-added Rh (Rh–P) catalysts showed this peak shifted to higher temperatures and lower intensity with higher P/Rh ratio or reduction temperature. Quantitative analysis of TPS profiles revealed that the amount of reacted H2S was remarkably lower (about 80 %) with P/Rh ratio more than 1.5, compared with Rh catalyst. The amount of reacted H2S decreased with greater intensity of the Rh2P peak in the XRD pattern, indicating that Rh2P has high sulfur tolerance. Furthermore, the relationship between P/Rh ratio and S/Rh ratio (calculated from TPS profile) of Rh–P catalysts agreed with the reported S/Rh value, showing the TPS method has high validity for qualitative analysis. We conclude that the TPS technique is a superior method for evaluation of sulfur tolerance for phosphide catalysts, and Rh2P has remarkably high sulfur tolerance compared with Rh catalyst.
- 1 May 2020
- Published by Japan Petroleum Institute in Journal of the Japan Petroleum Institute
- Vol. 63 (3) , 141-148
Open AccessSulfur Tolerance Properties of Rhodium Phosphide Evaluated by a New Temperature-programmed Sulfidation Technique
Sulfur tolerance properties of rhodium phosphide (Rh2P) were qualitatively and quantitatively evaluated by the temperature-programmed sulfidation (TPS) technique. The TPS profile of the Rh/SiO2 catalyst demonstrated a peak attributed to Rh2S3 formation around 400 °C. The TPS profiles of P-added Rh (Rh–P) catalysts showed this peak shifted to higher temperatures and lower intensity with higher P/Rh ratio or reduction temperature. Quantitative analysis of TPS profiles revealed that the amount of reacted H2S was remarkably lower (about 80 %) with P/Rh ratio more than 1.5, compared with Rh catalyst. The amount of reacted H2S decreased with greater intensity of the Rh2P peak in the XRD pattern, indicating that Rh2P has high sulfur tolerance. Furthermore, the relationship between P/Rh ratio and S/Rh ratio (calculated from TPS profile) of Rh–P catalysts agreed with the reported S/Rh value, showing the TPS method has high validity for qualitative analysis. We conclude that the TPS technique is a superior method for evaluation of sulfur tolerance for phosphide catalysts, and Rh2P has remarkably high sulfur tolerance compared with Rh catalyst.