KTKristi Timmo

Kristi Timmo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kristi Timmo has a total of 76 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Modification of the CZTS/CdS interface by introducing an intermediate CeO2 layer

    by K. Timmo, M. Pilvet, M. Danilson, V. Mikli, J. Krustok, A. Dolski, A. Nasyori, S. Bereznev, M. Grossberg-Kuusk, M. Kauk-Kuusik

  • Open Access

    Deep-Defect Suppression in Sb2Se3 via Atmosphere-Dependent Selenization Probed by Photoluminescence Spectroscopy

    by Nafiseh Abbasi, Jüri Krustok, Reelika Kaupmees, Kristi Timmo, Valdek Mikli, Marit Kauk-Kuusik, Maarja Grossberg-Kuusk

    The recombination dynamics in Sb2Se3 are strongly governed by intrinsic defect states, which limit carrier lifetime and solar cell device performance. In this work, the influence of post-growth selenization under controlled vapor pressure conditions on defect-related recombination in Sb2Se3 polycrystals is investigated using temperature- and excitation power-dependent photoluminescence (PL) spectroscopy. Structural characterization confirms preservation of the orthorhombic phase after selenization, while Raman analysis indicates improved crystallinity, particularly for the sample selenized under argon atmosphere. The as-grown polycrystals exhibit four emission bands at 0.88 eV, 1.10 eV, 1.22 eV, and 1.29 eV, corresponding to recombination via deep localized defect states (0.88 eV), grain-boundary-related states (1.10 eV), donor-acceptor pair (DAP) (1.22 eV), and excitonic (1.29 eV) recombination, respectively. Upon selenization, the grain-boundary-related and donor–acceptor pair recombination bands are suppressed, while the deep-level emission is significantly reduced but remains present, and excitonic emission becomes dominant. Excitation power-dependent measurements further confirm the distinction between defect-related and excitonic recombination mechanisms. Overall, the results demonstrate that increasing vapor pressure during selenization effectively suppresses radiative recombination via defect states and enhances excitonic edge emission, identifying vapor pressure as a key parameter controlling defect-mediated radiative recombination in Sb2Se3.

  • Open Access

    Radiative recombination model for BiSeI microcrystals: unveiling deep defects through photoluminescence

    by Marc Dolcet Sadurni, Jüri Krustok, Kristi Timmo, Valdek Mikli, Rokas Kondrotas, Maarja Grossberg-Kuusk, Marit Kauk-Kuusik

    Pnictogen chalcohalides are semiconductors that have emerged as promising materials for energy conversion due to their exceptional optoelectronic properties. Their electronic configuration (ns2), particularly for Bi- and Sb-based compounds, can be a key factor in efficient carrier transport and defect tolerance, similarly, to Pb-perovskites. In the present study, the Bi-containing chalcohalide, bismuth selenoiodide (BiSeI) was synthesized via isothermal heat treatment of binary precursors in evacuated quartz ampoules. The synthesized BiSeI microcrystals exhibited a characteristic needle-like morphology and a near-stoichiometric composition. Both indirect and direct band gap energies of BiSeI were determined by ultraviolet–visible–near-infrared diffuse reflectance spectroscopy, with room temperature values of 1.17 eV and 1.29 eV, respectively. This study presents the first experimental investigation of the photoluminescence properties of BiSeI microcrystals resulting in a recombination model involving multiple defect states. This work provides valuable insights into the defect structure and recombination mechanisms within BiSeI, paving the way for further exploration of its potential in optoelectronic devices.


  • Open Access

    Preparation and characterization of SbSeI thin films

    by Marc Dolcet Sadurni, Kristi Timmo, Valdek Mikli, Olga Volobujeva, Idil Mengü, Jüri Krustok, Maarja Grossberg-Kuusk, Marit Kauk-Kuusik


  • Open Access

    Tunneling-enhanced interface recombination and current loss curves in kesterite solar cells

    by Jüri Krustok, Kristi Timmo, Marit Kauk-Kuusik, Maarja Grossberg-Kuusk

    An approach to developing durable, light-weight, flexible, and semi-transparent solar cells is through the utilization of Cu2ZnSnS4 (CZTS) monograin powder. However, CZTS cells are currently far from their theoretically predicted efficiency. One reason for this is tunneling-enhanced interface recombination, which leads to a decrease in VOC and FF under higher forward bias conditions. We calculated the current loss curves JR–V of three different CZTS monograin layer solar cells for this report by subtracting the dark J–V curve from the light curve and adding a short circuit current density JSC. By quantum tunneling of holes through a bell-shaped potential barrier with additional recombination at the interface between CdS and CZTS, the shape of the current loss curve was examined. We showed that using the derivative dJR/dV of the measured curves allows us to simplify our analysis. The maximum position of this curve is proportional to the effective barrier height, and the intensity and the full width at half maximum give information about the width. At lower temperatures, the effective barrier height increases according to our theoretical model. We demonstrated that the properties of CZTS solar cells may be significantly enhanced by eliminating current loss at higher bias voltages.


  • Open Access

    Cu2ZnSnS4 monograin layer solar cells for flexible photovoltaic applications

    by Marit Kauk-Kuusik, Kristi Timmo, Maris Pilvet, Katri Muska, Mati Danilson, Jüri Krustok, Raavo Josepson, Valdek Mikli, Maarja Grossberg-Kuusk

    Monograin powder technology is one possible path to developing sustainable, lightweight, flexible, and semi-transparent solar cells, which might be ideal for integration with various building and product elements. In recent years, the main research focus of monograin technology has centered around understanding the synthesis and optoelectronic properties of kesterite-type absorber materials. Among these, Cu2ZnSnS4 (CZTS) stands out as a promising solar cell absorber due to its favorable optical and electrical characteristics. CZTS is particularly appealing as its constituent elements are abundant and non-toxic, and it currently holds the record for highest power conversion efficiency (PCE) among emerging inorganic thin-film PV candidates. Despite its advantages, kesterite solar cells' PCE still falls significantly behind the theoretical maximum efficiency due to the large VOC deficit. This review explores various strategies aimed at improving VOC losses to enhance the overall performance of CZTS monograin layer solar cells. It was found that low-temperature post-annealing of CZTS powders reduced Cu–Zn disordering, increasing Eg by ∼100 meV and VOC values; however, achieving the optimal balance between ordered and disordered regions in kesterite materials is crucial for enhancing photovoltaic device performance due to the coexistence of ordered and disordered phases. CZTS alloying with Ag and Cd suppressed non-radiative recombination and increased short-circuit current density. Optimizing Ag content at 1% reduced CuZn antisite defects, but higher Ag levels compensated for acceptor defects, leading to reduced carrier density and decreased solar cell performance. Co-doping with Li and K resulted in an increased bandgap (1.57 eV) and improved VOC, but further optimization is required due to a relatively large difference between measured and theoretical VOC. Heterojunction modifications led to the most effective PCE improvement in CZTS-based solar cells, achieving an overall efficiency of 12.06%.


  • Open Access

    Influence of alkali iodide fluxes on Cu2ZnSnS4 monograin powder properties and performance of solar cells

    by Kristi Timmo, Maris Pilvet, Katri Muska, Mare Altosaar, Valdek Mikli, Reelika Kaupmees, Raavo Josepson, Jüri Krustok, Maarja Grossberg-Kuusk, Marit Kauk-Kuusik

    One promising and cost-effective method to produce flexible solar panels in the future is monograin layer (MGL) solar cell technology based on monograin powder (MGP) crystals. The results of the present study demonstrate the influence of different alkali salts (LiI, NaI, KI, RbI and CsI) on the properties of Cu2ZnSnS4 (CZTS) MGPs and their effect on the characteristics of MGL solar cells. SEM and EDX studies revealed that the morphology and composition of the formed crystals are influenced by the nature of the flux materials. Structural studies by XRD showed good crystallinities for all MGPs. However, CZTS crystals grown in LiI exhibited a shift of all diffraction peaks towards lower angles and larger lattice parameter values. In addition, powder grown in LiI exhibited the broadest main Raman peak (FWHM = 7.06 cm−1). When CsI was used, the Raman peaks were sharper and narrower with FWHM of 4.5 cm−1, showing a higher level of crystallinity compared to other produced powders. The estimated band gap energy values obtained from EQE measurements were ∼1.57 eV for NaI, KI, RbI, CsI and 1.65 eV for LiI grown CZTS MGPs. The analysis of temperature-dependent current–voltage characteristics indicated that tunneling enhanced interface recombination is the prevailing process in all materials. At low temperatures, the powder crystals grown in LiI, NaI, and RbI revealed the presence of recombination channels that were not observed at room temperature. The MGL solar cell based on CZTS powder grown in CsI resulted in the highest power conversion efficiency of 10.9%.


  • Open Access

    Cu2ZnSnS4 Monograin Layer Solar Cells for Flexible Photovoltaic Applications

    by Kauk-Kuusik Marit, Kristi Timmo, Maris Pilvet, Katri Muska, Mati Danilson, Jüri Krustok, Raavo Josepson, Grossberg-Kuusk Maarja

    Flexible photovoltaics have been and will be increasingly demanded in various applications in todays and future society. The search for an ideal flexible photovoltaic technology that can perfectly meet these expanding demands has long been an active branch of photovoltaic research. Monograin layer technology (MGL) is one possible path to develop the lightweight, flexible, and semi-transparent solar cells. The major innovations in the MGL solar cell technology are the light absorbing layer made of high quality micro-crystalline semiconductor powder enabling theoretically higher efficiencies and the low cost and easily up-scalable roll-to-roll PV module production process. In recent years, the main research focus of the monograin technology has been on the understanding of the synthesis and optoelectronic properties of Cu2ZnSnS4 absorber materials. The highest power conversion efficiency of this type of devices is 12.06% with output parameters as follows: VOC =0.745 V, JSC=28.36 mA/cm2 and FF = 57.10 %. In this study temperature dependence (T = 20- 320K) of current-voltage (J-V) characteristics of record efficiency Cu2ZnSnS4 MGL solar cell were investigated to clarify the main losses in CZTS, which are still not fully understood. The light J−V curve analysis was used to evaluate the quality of the p−n junction and losses related to resistive components of the device. In this study, the single exponential diode equation was employed to analyze the light J−V data. It turned out that at lower temperatures (T < 180 K) a second blocking diode appears and it is related to back contact barrier. We believe that this back contact barrier has an effect also at higher temperatures causing relative low values of FF. At T=300 K the diode ideality factor n has a value 2.58 and the series resistance Rs =2.6 Ωcm2.

  • Open Access

    Influence of Alkali Iodide Fluxes on Cu2ZnSnS4 Monograin Powder Properties and Performance of Solar Cells

    by Kristi Timmo, Katri Muska, Maris Pilvet, Mare Altosaar, Valdek Mikli, Mati Danilson, Reelika Kaupmees, Jüri Krustok, Maarja Grossberg-Kuusk, Marit Kauk-Kuusik

    Molten salt synthesis-growth method is one possibility to produce very high-quality monocrystalline absorber materials in powder form for flexible solar cells. Results of the current study show the influence of different alkali salts on the CZTS monograin powder (MGP) properties and impact on the performance of monograin layer (MGL) solar cells. Cu1.84Zn1.09Sn0.99S4 powders were synthesized from CuS, ZnS and SnS by isothermal molten salt synthesis-growth method in the presence of molten LiI, NaI, KI, RbI and CsI salts as flux materials in sealed vacuum quartz ampoules at 740 oC. SEM and EDX studies showed that the morphology and composition of the formed crystals are influenced by the nature of the flux materials. Structural studies by XRD revealed a shift of all diffraction peaks towards lower angles for CZTS crystals grown in LiI and a larger lattice parameter values in comparison with powder crystals formed in CsI, RbI, NaI and KI. CZTS MGPs grown in LiI also showed the widest main Raman peak (FWHM=7.06 cm-1). In case of CsI, Raman peaks were sharper and narrower (FWHM=4.5 cm-1) compared to the other produced powders, showing a higher level of crystallinity. The estimated effective bandgap energy values from EQE measurements were ~1.57 eV and 1.66 eV for CZTS MGPs grown in NaI, KI, RbI, CsI and in LiI, respectively. In addition, detailed analysis of photoluminescence spectroscopy and temperature dependent solar cell parameters will be discussed. The highest efficiency of 10.88% was achieved with MGL solar cell based on CZTS grown in CsI.