Yongping Luo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yongping Luo has a total of 104 co-authors. Here are the top co-authors by number of shared publications:
- Shunjian Xu
School of Intelligent Manufacturing, Huzhou College, Huzhou 313000, China
21 shared publications - Zonghu Xiao
Xinyu Institute of New Energy, Xinyu University, Xinyu 338004, China
17 shared publications - Wei Zhong
Xinyu Institute of New Energy, Xinyu University, Xinyu 338004, China
16 shared publications Yang Tian
14 shared publications- Anwei Zhu
School of Chemistry and Molecular Engineering East China Normal University Shanghai P. R. China
13 shared publications Hui Ou
Xinyu Institute of New Energy, Xinyu University, Xinyu, China
13 shared publications
Latest Publications
- 6 January 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (2) , 4235-4242
Multicolor-Emissive Carbon Quantum Dots Sensitized into Nanolaminated Piezoelectric Biofilms for Multifunctional Sensing
In response to the evolving applications of intelligent systems, the fluorescent pressure sensor (FPS) has been proposed but usually with complicated structure design. Herein, we develop a multicolor-emissive FPS through simply sensitizing carbon quantum dots (CQDs) into nanolaminated biofilms. The multicolor fluorescence derived from three types of CQDs was successfully implanted into the piezoelectric cucumber pulp slices (CPS), which was subsequently verified to be also feasible in grape peels. The suppression of aggregation-induced quenching in the hybrid film is attributed to the imitated sensitizer/photoelectrode structure (ISP) with two features: (i) the nanolaminated matrix supported uniform distribution of the CQDs and (ii) the interfacial bonding between the CQDs and the matrix. The ISP structure also awakens a charming bridging effect from CQDs, leading to the significantly improved piezoelectric performance of the hybrid films. Due to the suitable size matching degree of 0.85 and the potential adding strong bonding supported by the unique sulfonic acid (SO3H), the red-emissive CQDs/CPS-based FPS possesses an optimal sensitivity of 38.6 mV N-1, which is 80.37% higher than that of the pure matrix (21.4 mV N-1). This renewable hybrid film-based FPS integrates multiple requirements, such as UV perception, tactile perception, and energy harvesting.
- 6 January 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (2) , 4235-4242
Multicolor-Emissive Carbon Quantum Dots Sensitized into Nanolaminated Piezoelectric Biofilms for Multifunctional Sensing
In response to the evolving applications of intelligent systems, the fluorescent pressure sensor (FPS) has been proposed but usually with complicated structure design. Herein, we develop a multicolor-emissive FPS through simply sensitizing carbon quantum dots (CQDs) into nanolaminated biofilms. The multicolor fluorescence derived from three types of CQDs was successfully implanted into the piezoelectric cucumber pulp slices (CPS), which was subsequently verified to be also feasible in grape peels. The suppression of aggregation-induced quenching in the hybrid film is attributed to the imitated sensitizer/photoelectrode structure (ISP) with two features: (i) the nanolaminated matrix supported uniform distribution of the CQDs and (ii) the interfacial bonding between the CQDs and the matrix. The ISP structure also awakens a charming bridging effect from CQDs, leading to the significantly improved piezoelectric performance of the hybrid films. Due to the suitable size matching degree of 0.85 and the potential adding strong bonding supported by the unique sulfonic acid (SO3H), the red-emissive CQDs/CPS-based FPS possesses an optimal sensitivity of 38.6 mV N-1, which is 80.37% higher than that of the pure matrix (21.4 mV N-1). This renewable hybrid film-based FPS integrates multiple requirements, such as UV perception, tactile perception, and energy harvesting.
- Open Access
- 31 May 2025
- Published by Royal Society of Chemistry (RSC) in Energy Advances
- Vol. 4 (7) , 947-957
Renewable flower-based dye-sensitized solar cells using natural dye and natural carbon counter electrode
Natural dyes and carbons prepared from five common flowers were facilely integrated into dye-sensitized solar cells.
- 31 May 2025
- Published by Royal Society of Chemistry (RSC) in Energy Advances
- Vol. 4 (7) , 947-957
Open AccessRenewable flower-based dye-sensitized solar cells using natural dye and natural carbon counter electrode
Natural dyes and carbons prepared from five common flowers were facilely integrated into dye-sensitized solar cells.
- 24 February 2024
- Published by Springer Nature in Journal of Materials Science
- Vol. 59 (8) , 3573-3584
Ag/g-C3N4 nanosheets as a progressive support of Pt catalyst for improved electrocatalytic oxidation of methanol
- 24 February 2024
- Published by Springer Nature in Journal of Materials Science
- Vol. 59 (8) , 3573-3584
Ag/g-C3N4 nanosheets as a progressive support of Pt catalyst for improved electrocatalytic oxidation of methanol
- 12 July 2023
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 25 (29) , 19553-19561
CoP-modified CdS for enhanced stability and photocatalytic hydrogen production under visible light
The weak electron–hole separation ability and the more severe photocorrosion of CdS largely limit its hydrogen precipitation performance. In this study, CoP loading on the surface of CdS was utilized to form a type I heterojunction. The photocurrent density increased from 2 μA cm−2 to 20 μA cm−2. When the loading of CoP was 10%, the best photocatalytic performance reached 4.43 mmolg−1 h−1 under visible light, which was 20.1 times higher than that of CdS (0.22 mmolg−1 h−1). In addition, the loading of CoP solved the problem of CdS photocorrosion. After 5 cycles of simulated solar irradiation, the performance of 10% CoP/CdS remained at 93% of the initial test. This work provides new ideas for the design of low photocorrosion and high-performance catalysts.
- 12 July 2023
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 25 (29) , 19553-19561
CoP-modified CdS for enhanced stability and photocatalytic hydrogen production under visible light
The weak electron–hole separation ability and the more severe photocorrosion of CdS largely limit its hydrogen precipitation performance. In this study, CoP loading on the surface of CdS was utilized to form a type I heterojunction. The photocurrent density increased from 2 μA cm−2 to 20 μA cm−2. When the loading of CoP was 10%, the best photocatalytic performance reached 4.43 mmolg−1 h−1 under visible light, which was 20.1 times higher than that of CdS (0.22 mmolg−1 h−1). In addition, the loading of CoP solved the problem of CdS photocorrosion. After 5 cycles of simulated solar irradiation, the performance of 10% CoP/CdS remained at 93% of the initial test. This work provides new ideas for the design of low photocorrosion and high-performance catalysts.
- 21 September 2022
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 6 (21) , 4893-4902
CdS/ZnIn 2 S 4 type II heterojunctions improve photocatalytic hydrogen production: faster electron–hole separation and wider visible light utilization
Type II heterojunction can expand the light utilization and improve the electron–hole separation efficiency. The best photocatalytic performance of 5%-CdS/ZIS reached 2.15 mmol g −1 h −1 under visible-light irradiation.
- 21 September 2022
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 6 (21) , 4893-4902
CdS/ZnIn 2 S 4 type II heterojunctions improve photocatalytic hydrogen production: faster electron–hole separation and wider visible light utilization
Type II heterojunction can expand the light utilization and improve the electron–hole separation efficiency. The best photocatalytic performance of 5%-CdS/ZIS reached 2.15 mmol g −1 h −1 under visible-light irradiation.
- Open Access
- 28 April 2022
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 12 (21) , 13440-13447
Enhanced electrocatalytic performance of N-doped carbon xerogels obtained through dual nitrogen doping for the oxygen reduction reaction
The development of high efficiency and low-cost electrocatalysts for the oxygen reduction reaction (ORR) is urgently desired for many energy storage and conversion systems. Nitrogen-doped carbon xerogels (NCXs) which have been successfully applied as effective electrocatalysts for the ORR have continued to attract attention due to their competitive price and tunable surface chemistry. A new dual N-doped NCX (NCoNC) electrocatalyst is fabricated as a carbon based catalyst though a facile impregnation of peptone in a precursor and ammonia etching pyrolysis method. XPS analysis demonstrates that the NCoNC electrocatalyst not only has a high N doping amount, but also has an optimized chemical state composition of N doping, which play an important role in improving the microstructure and catalytic performance of the catalysts. XRD and HRTEM results show that the doped metal nano-particles are coated with a double carbon layer of graphene carbon (inner layer) and amorphous carbon (outer layer) forming serrated edges that facilitate the ORR process. The as-obtained NCoNC catalyst exhibits good electrocatalytic performance and excellent stability for the ORR in both acidic and alkaline environments. In particular, in alkaline electrolyte, the decrements of both the limiting current density and the half-wave potential of the NCoNC catalyst were significantly lower than those of a commercial Pt/C catalyst during accelerated aging tests. When serving as an air electrode in Zn–air batteries, the catalyst also exhibits superior catalytic performance with a peak power density of 78.2 mW cm−2 and a stable open-circuit voltage of 1.37–1.43 V. This work presents a novel tactic to regulate the microstructure and composition of carbon-based electrocatalysts by the facile and scalable dual-effect nitrogen doping method which may be conducive to promoting and developing highly efficient and promising electrocatalysts for the ORR.
- 28 April 2022
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 12 (21) , 13440-13447
Open AccessEnhanced electrocatalytic performance of N-doped carbon xerogels obtained through dual nitrogen doping for the oxygen reduction reaction
The development of high efficiency and low-cost electrocatalysts for the oxygen reduction reaction (ORR) is urgently desired for many energy storage and conversion systems. Nitrogen-doped carbon xerogels (NCXs) which have been successfully applied as effective electrocatalysts for the ORR have continued to attract attention due to their competitive price and tunable surface chemistry. A new dual N-doped NCX (NCoNC) electrocatalyst is fabricated as a carbon based catalyst though a facile impregnation of peptone in a precursor and ammonia etching pyrolysis method. XPS analysis demonstrates that the NCoNC electrocatalyst not only has a high N doping amount, but also has an optimized chemical state composition of N doping, which play an important role in improving the microstructure and catalytic performance of the catalysts. XRD and HRTEM results show that the doped metal nano-particles are coated with a double carbon layer of graphene carbon (inner layer) and amorphous carbon (outer layer) forming serrated edges that facilitate the ORR process. The as-obtained NCoNC catalyst exhibits good electrocatalytic performance and excellent stability for the ORR in both acidic and alkaline environments. In particular, in alkaline electrolyte, the decrements of both the limiting current density and the half-wave potential of the NCoNC catalyst were significantly lower than those of a commercial Pt/C catalyst during accelerated aging tests. When serving as an air electrode in Zn–air batteries, the catalyst also exhibits superior catalytic performance with a peak power density of 78.2 mW cm−2 and a stable open-circuit voltage of 1.37–1.43 V. This work presents a novel tactic to regulate the microstructure and composition of carbon-based electrocatalysts by the facile and scalable dual-effect nitrogen doping method which may be conducive to promoting and developing highly efficient and promising electrocatalysts for the ORR.
- 1 November 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (11) , 116520
A Simple g-C 3 N 4 /TNTs Heterojunction for Improving the Photoelectrocatalytic Degradation of Methyl Orange
In this work, highly ordered titanium dioxide nanotube arrays (TNTs) were first prepared by anodic oxidation method. Then, g-C 3 N 4 /TNTs heterojunctions were prepared by ultrasonically loading graphitic carbon nitride (g-C 3 N 4 ) onto the TNTs. The morphology and crystal structure of TNTs and g-C 3 N 4 /TNTs were characterized by SEM/TEM and XRD. The photoelectrocatalytic (PEC) degradation of methyl orange (MO) by TNTs and g-C 3 N 4 /TNTs was studied in a PEC degradation system. The photocatalytic (PC), electrocatalytic (EC), and PEC degradation properties were compared, and the effect of pollutant concentration on the degradation performance of the catalysts was analyzed. According to the experimental results, the degradation rate of MO with TNTs only reaches 65.1% after 120 min, while the degradation rate of MO with g-C 3 N 4 /TNTs reaches 84.6% in the same time. Due to the synergistic effect of light and electricity, the PEC degradation efficiency of the two catalysts is greater than the sum of PC and EC degradation, proving that g-C 3 N 4 /TNTs heterojunctions provide excellent PEC performance for the degradation of MO.
- 1 November 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (11) , 116520
A Simple g-C 3 N 4 /TNTs Heterojunction for Improving the Photoelectrocatalytic Degradation of Methyl Orange
In this work, highly ordered titanium dioxide nanotube arrays (TNTs) were first prepared by anodic oxidation method. Then, g-C 3 N 4 /TNTs heterojunctions were prepared by ultrasonically loading graphitic carbon nitride (g-C 3 N 4 ) onto the TNTs. The morphology and crystal structure of TNTs and g-C 3 N 4 /TNTs were characterized by SEM/TEM and XRD. The photoelectrocatalytic (PEC) degradation of methyl orange (MO) by TNTs and g-C 3 N 4 /TNTs was studied in a PEC degradation system. The photocatalytic (PC), electrocatalytic (EC), and PEC degradation properties were compared, and the effect of pollutant concentration on the degradation performance of the catalysts was analyzed. According to the experimental results, the degradation rate of MO with TNTs only reaches 65.1% after 120 min, while the degradation rate of MO with g-C 3 N 4 /TNTs reaches 84.6% in the same time. Due to the synergistic effect of light and electricity, the PEC degradation efficiency of the two catalysts is greater than the sum of PC and EC degradation, proving that g-C 3 N 4 /TNTs heterojunctions provide excellent PEC performance for the degradation of MO.
- 20 July 2021
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 32 (16) , 21178-21187
High-performance Ag nanowires/PEDOT:PSS composite electrodes for PVDF-HFP piezoelectric nanogenerators
- 20 July 2021
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 32 (16) , 21178-21187
High-performance Ag nanowires/PEDOT:PSS composite electrodes for PVDF-HFP piezoelectric nanogenerators
- 15 June 2021
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 45 (29) , 12879-12885
Improved electrocatalytic activity of Pt catalyst supported on core–shell CMs@NiO for methanol oxidation
The enhancement of the electrocatalytic oxidation of methanol was achieved by utilizing core–shell carbon microspheres@NiO (CMs@NiO) deposited on glassy carbon (GC) as the support material for Pt catalyst. The resultant CMs@NiO/Pt catalyst was prepared via a simple electrodeposition method for supporting Pt nanoparticles (NPs) on CMs@NiO. The obtained CMs@NiO and/or CMs@NiO/Pt were characterized by SEM, TEM, XRD and XPS, which can directly prove that the core–shell structure is formed and Pt NPs are successfully immobilized on CMs@NiO. The electrochemical experiments (CV and i–t) showed that CMs@NiO/Pt has obvious electrocatalytic activity and stability compared with CMs/Pt, NiO/Pt and commerical C/Pt, which can be attributed to the synergetic effects of CMs@NiO and Pt NPs. It was found that the CMs@NiO/Pt catalyst is beneficial to alleviate the CO poisoning effects for methanol electrooxidation, which was demonstrated by the higher ratio (Jf/Jb) of the forward anodic peak current density (Jf) to the backward anodic peak current density (Jb). A possible mechanism was also proposed that the Pt catalyst supported on CMs@NiO improved the CO tolerance for methanol electrooxidation. The results suggest that the core–shell CMs@NiO could be used as a practical supporting material for preparing electrocatalysts suitable for the methanol electrooxidation application.
- 15 June 2021
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 45 (29) , 12879-12885
Improved electrocatalytic activity of Pt catalyst supported on core–shell CMs@NiO for methanol oxidation
The enhancement of the electrocatalytic oxidation of methanol was achieved by utilizing core–shell carbon microspheres@NiO (CMs@NiO) deposited on glassy carbon (GC) as the support material for Pt catalyst. The resultant CMs@NiO/Pt catalyst was prepared via a simple electrodeposition method for supporting Pt nanoparticles (NPs) on CMs@NiO. The obtained CMs@NiO and/or CMs@NiO/Pt were characterized by SEM, TEM, XRD and XPS, which can directly prove that the core–shell structure is formed and Pt NPs are successfully immobilized on CMs@NiO. The electrochemical experiments (CV and i–t) showed that CMs@NiO/Pt has obvious electrocatalytic activity and stability compared with CMs/Pt, NiO/Pt and commerical C/Pt, which can be attributed to the synergetic effects of CMs@NiO and Pt NPs. It was found that the CMs@NiO/Pt catalyst is beneficial to alleviate the CO poisoning effects for methanol electrooxidation, which was demonstrated by the higher ratio (Jf/Jb) of the forward anodic peak current density (Jf) to the backward anodic peak current density (Jb). A possible mechanism was also proposed that the Pt catalyst supported on CMs@NiO improved the CO tolerance for methanol electrooxidation. The results suggest that the core–shell CMs@NiO could be used as a practical supporting material for preparing electrocatalysts suitable for the methanol electrooxidation application.