Xiaoqi Jia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Xiaoqi Jia has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Bao-Ling Cui
Key Laboratory of Fluid Transmission Technology of Zhejiang Province, Zhejiang Sci-Tech University , Hangzhou 310018, China
1 shared publication - Baoling Cui
Zhejiang Key Laboratory of Multiflow and Fluid Machinery, Zhejiang Sci-tech University, Hangzhou 310018, China
1 shared publication - Bowen Li
National-Provincial Joint Engineering Laboratory for Fluid Transmission System Technology, Zhejiang Sci-Tech University, 5 Second Avenue, Xiasha Higher Education Zone, Hangzhou 310018, China
1 shared publication - Feng Chen
Department of Mechanical Technology, Zhejiang Institute of Mechanical and Electrical Engineering, Hangzhou 310053, China
1 shared publication - Hua Fang
National-Provincial Joint Engineering Laboratory for Fluid Transmission System Technology, Zhejiang Sci-Tech University, Hangzhou 310018, China
1 shared publication Kun Rao
Zhejiang Sci Tech Univ, Fac Mech Engn & Automat, Hangzhou, Zhejiang, Peoples R China
1 shared publication
Latest Publications
- Open Access
The Role of Blade Sinusoidal Tubercle Trailing Edge in a Centrifugal Pump with Low Specific Speed
Pressure pulsations may cause high-amplitude vibrations during the process of a centrifugal pump. The trailing edge shape of the blade has a critical influence on the pump’s pressure fluctuation and hydraulic characterization. In this paper, inspired by the humpback whale flipper, the authors research the impact of applying the sinusoidal tubercles to the blade suction side of the trailing edge. Numerical calculation and experiments are carried out to investigate the impact of the trailing edge shape on the pressure pulsations and performance of a centrifugal pump with low specific speed. Two designed impellers are tested, one is a sinusoidal tubercle trailing edge (STTE) impeller and the other is the original trailing edge (OTE) prototype. The detailed study indicates that the sinusoidal tubercle trailing edge (STTE) reduces pressure pulsation and enhances hydraulic performance. In the volute tongue region, the pressure pulsation amplitudes of STTE at fBPF decrease significantly. The STTE impeller also effectively changes the vortex structure and intensity in the blade trailing edge area. This investigation will be of great benefit to the optimal design of pumps.
Open AccessThe Role of Blade Sinusoidal Tubercle Trailing Edge in a Centrifugal Pump with Low Specific Speed
Pressure pulsations may cause high-amplitude vibrations during the process of a centrifugal pump. The trailing edge shape of the blade has a critical influence on the pump’s pressure fluctuation and hydraulic characterization. In this paper, inspired by the humpback whale flipper, the authors research the impact of applying the sinusoidal tubercles to the blade suction side of the trailing edge. Numerical calculation and experiments are carried out to investigate the impact of the trailing edge shape on the pressure pulsations and performance of a centrifugal pump with low specific speed. Two designed impellers are tested, one is a sinusoidal tubercle trailing edge (STTE) impeller and the other is the original trailing edge (OTE) prototype. The detailed study indicates that the sinusoidal tubercle trailing edge (STTE) reduces pressure pulsation and enhances hydraulic performance. In the volute tongue region, the pressure pulsation amplitudes of STTE at fBPF decrease significantly. The STTE impeller also effectively changes the vortex structure and intensity in the blade trailing edge area. This investigation will be of great benefit to the optimal design of pumps.
- 8 May 2018
- Published by Emerald Publishing in Engineering Computations
- Vol. 35 (3) , 1500-1511
Analysis of unsteady radial forces of multistage centrifugal pump with double volute
Radial vibration of horizontal centrifugal pump has a close association with radial exciting forces. The purpose of this paper is to analyze the unsteady radial force in multistage centrifugal pump with double volute in detail and investigate the relevance of static pressure, radial force and radial vibration. The unsteady numerical simulation with Realizable k-ε turbulence model was carried out for a multistage centrifugal pump with double volute using computational fluid dynamics codes Fluent. The performance tests were conducted by a closed loop system and performance curves from numerical simulation agree with that of experiment. Vibration tests were carried out by vibration probes instrumented on the bearing cover of pump near no-driven end. Fast Fourier Transform was used to obtain the frequency components of radial forces on the impellers from numerical simulation, which are compared with ones of radial vibration from experiment in Y and Z direction. And the static pressure distributions in the impeller were analyzed under different flow rates. The symmetrical double volute can effectively balance radial forces. The maximum radial force and vibration velocity appear at 0.6 Q among the three flow rates 0.6 Q, Q and 1.2 Q. The frequencies corresponding to relatively large amplitude of vibration velocities and radial forces on the impellers in Y direction are blade passing frequency of the impellers. Blade passing frequency of first-stage impeller and shaft frequency are predominating in Z direction. It indicates that the radial vibration of centrifugal pump is closely related to the unsteady radial force. The unsteady radial forces of the impeller in multistage centrifugal pump with double volute were comprehensively analyzed. The radial forces should be considered to balance during the design of multistage centrifugal pump.
- 8 May 2018
- Published by Emerald Publishing in Engineering Computations
- Vol. 35 (3) , 1500-1511
Analysis of unsteady radial forces of multistage centrifugal pump with double volute
Radial vibration of horizontal centrifugal pump has a close association with radial exciting forces. The purpose of this paper is to analyze the unsteady radial force in multistage centrifugal pump with double volute in detail and investigate the relevance of static pressure, radial force and radial vibration. The unsteady numerical simulation with Realizable k-ε turbulence model was carried out for a multistage centrifugal pump with double volute using computational fluid dynamics codes Fluent. The performance tests were conducted by a closed loop system and performance curves from numerical simulation agree with that of experiment. Vibration tests were carried out by vibration probes instrumented on the bearing cover of pump near no-driven end. Fast Fourier Transform was used to obtain the frequency components of radial forces on the impellers from numerical simulation, which are compared with ones of radial vibration from experiment in Y and Z direction. And the static pressure distributions in the impeller were analyzed under different flow rates. The symmetrical double volute can effectively balance radial forces. The maximum radial force and vibration velocity appear at 0.6 Q among the three flow rates 0.6 Q, Q and 1.2 Q. The frequencies corresponding to relatively large amplitude of vibration velocities and radial forces on the impellers in Y direction are blade passing frequency of the impellers. Blade passing frequency of first-stage impeller and shaft frequency are predominating in Z direction. It indicates that the radial vibration of centrifugal pump is closely related to the unsteady radial force. The unsteady radial forces of the impeller in multistage centrifugal pump with double volute were comprehensively analyzed. The radial forces should be considered to balance during the design of multistage centrifugal pump.
- 22 February 2017
- Published by Walter de Gruyter GmbH in International Journal of Turbo & Jet-Engines
- Vol. 36 (4) , 401-410
Experimental Investigation of Pressure Fluctuations on Inner Wall of a Centrifugal Pump
Affected by rotor–stator interaction and unstable inner flow, asymmetric pressure distributions and pressure fluctuations cannot be avoided in centrifugal pumps. To study the pressure distributions on volute and front casing walls, dynamic pressure tests are carried out on a centrifugal pump. Frequency spectrum analysis of pressure fluctuation is presented based on Fast Fourier transform and steady pressure distribution is obtained based on time-average method. The results show that amplitudes of pressure fluctuation and blade-passing frequency are sensitive to the flow rate. At low flow rates, high-pressure region and large pressure gradients near the volute tongue are observed, and the main factors contributing to the pressure fluctuation are fluctuations in blade-passing frequency and high-frequency fluctuations. By contrast, at high flow rates, fluctuations of rotating-frequency and low frequencies are the main contributors to pressure fluctuation. Moreover, at low flow rates, pressure near volute tongue increases rapidly at first and thereafter increases slowly, whereas at high flow rates, pressure decreases sharply. Asymmetries are observed in the pressure distributions on both volute and front casing walls. With increasing of flow rate, both asymmetries in the pressure distributions and magnitude of the pressure decrease.
- 22 February 2017
- Published by Walter de Gruyter GmbH in International Journal of Turbo & Jet-Engines
- Vol. 36 (4) , 401-410
Experimental Investigation of Pressure Fluctuations on Inner Wall of a Centrifugal Pump
Affected by rotor–stator interaction and unstable inner flow, asymmetric pressure distributions and pressure fluctuations cannot be avoided in centrifugal pumps. To study the pressure distributions on volute and front casing walls, dynamic pressure tests are carried out on a centrifugal pump. Frequency spectrum analysis of pressure fluctuation is presented based on Fast Fourier transform and steady pressure distribution is obtained based on time-average method. The results show that amplitudes of pressure fluctuation and blade-passing frequency are sensitive to the flow rate. At low flow rates, high-pressure region and large pressure gradients near the volute tongue are observed, and the main factors contributing to the pressure fluctuation are fluctuations in blade-passing frequency and high-frequency fluctuations. By contrast, at high flow rates, fluctuations of rotating-frequency and low frequencies are the main contributors to pressure fluctuation. Moreover, at low flow rates, pressure near volute tongue increases rapidly at first and thereafter increases slowly, whereas at high flow rates, pressure decreases sharply. Asymmetries are observed in the pressure distributions on both volute and front casing walls. With increasing of flow rate, both asymmetries in the pressure distributions and magnitude of the pressure decrease.