Pavel V. Chumakov
Research Subjects
Pavel V. Chumakov has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Igor Nikolaevich Kravchenko
Mechanical Engineering Research Institute of the Russian Academy of Sciences, Moscow, Russia
3 shared publications - Alexei V. Martynov
National Research Mordovia State University
2 shared publications - Sergey A. Velichko
Ogarev National Research Mordovian State University, Saransk, Russia
2 shared publications - Alexander A. Gutsan
Bryansk State Agrarian University
1 shared publication - Alexander V. Kolomeichenko
Parakhin Orel State Agrarian University
1 shared publication Alexander V. Kolomeychenko
Agricultural Engineering Centre NAMI
1 shared publication
Latest Publications
- Open Access
- 25 March 2025
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 35 (1) , 155-169
The use of Epoxy-Gravel Composites to Harden Composite Ploughshares with the Possibility of Restoring the Components Having Radial Wear
Introduction. The resistance of soil cultivation equipment components to abrasive wear is an important operational characteristic. Employing various methods to harden the surfaces of these components is an important task for agricultural machinery manufacturing. This article focuses on studying the effectiveness of using epoxy-gravel composites to harden composite ploughshares operating under conditions causing increased abrasive wear.Aim of the Study. The study is aimed at substantiating the practical application of epoxygravel composites to harden composite ploughshares with the ability to restore the components having radial wear.Materials and Methods. Within the framework of the study on restoring worn ploughshares of the reversible plough produced by “Kverneland Group” company and aggregated with the tractor “Kirovets K-744”, there were used coatings based on epoxy composite with gravel crumbs of different fractions, in which the ratio of epoxy compound to gravel filler was 50:50. During the machine-tractor unit operation, there was monitored the wear dynamics of the restored ploughshares. The ploughshares under study differed among themselves by the fraction of gravel crumbs in the epoxy composite. For each ploughshare under study, there were plotted the dependence of wear dynamics on operating time.Results. The use of gravel chips with a dispersion of gravel particles of 1.75 mm in epoxy resin has shown the best resistance to abrasive wear. The optimal operational characteristics of the composite derive from the high adhesion of the particles to the epoxy base that prevents their delamination and provides the stability of the coating under mechanical and shock loads. This proves the effectiveness of using epoxy-gravel composites to harden the working surfaces of ploughshares that in the conditions of abrasive wear reduce the probability of radial wear.Discussion and Conclusion. The conducted studies confirm that the use of epoxy-gravel composites makes it possible to increase the wear resistance of coatings by 2.8 times compared with factory-made parts. This allows increasing the service life of ploughshares operating under conditions of intense abrasive friction. The use of epoxy-gravel composites to harden ploughshares is important for agricultural enterprises, because of the high resource of hardened surfaces during their operation.
- 25 March 2025
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 35 (1) , 155-169
Open AccessThe use of Epoxy-Gravel Composites to Harden Composite Ploughshares with the Possibility of Restoring the Components Having Radial Wear
Introduction. The resistance of soil cultivation equipment components to abrasive wear is an important operational characteristic. Employing various methods to harden the surfaces of these components is an important task for agricultural machinery manufacturing. This article focuses on studying the effectiveness of using epoxy-gravel composites to harden composite ploughshares operating under conditions causing increased abrasive wear.Aim of the Study. The study is aimed at substantiating the practical application of epoxygravel composites to harden composite ploughshares with the ability to restore the components having radial wear.Materials and Methods. Within the framework of the study on restoring worn ploughshares of the reversible plough produced by “Kverneland Group” company and aggregated with the tractor “Kirovets K-744”, there were used coatings based on epoxy composite with gravel crumbs of different fractions, in which the ratio of epoxy compound to gravel filler was 50:50. During the machine-tractor unit operation, there was monitored the wear dynamics of the restored ploughshares. The ploughshares under study differed among themselves by the fraction of gravel crumbs in the epoxy composite. For each ploughshare under study, there were plotted the dependence of wear dynamics on operating time.Results. The use of gravel chips with a dispersion of gravel particles of 1.75 mm in epoxy resin has shown the best resistance to abrasive wear. The optimal operational characteristics of the composite derive from the high adhesion of the particles to the epoxy base that prevents their delamination and provides the stability of the coating under mechanical and shock loads. This proves the effectiveness of using epoxy-gravel composites to harden the working surfaces of ploughshares that in the conditions of abrasive wear reduce the probability of radial wear.Discussion and Conclusion. The conducted studies confirm that the use of epoxy-gravel composites makes it possible to increase the wear resistance of coatings by 2.8 times compared with factory-made parts. This allows increasing the service life of ploughshares operating under conditions of intense abrasive friction. The use of epoxy-gravel composites to harden ploughshares is important for agricultural enterprises, because of the high resource of hardened surfaces during their operation.
- 1 September 2024
- Published by Allerton Press in Russian Engineering Research
- Vol. 44 (9) , 1240-1243
Improving the Reliability of Pipe End Joints Using Shape Memory
A technology is developed for connecting pipes by means of sleeves or fittings made of materials with shape memory. When using this technology, joints in p
- 1 September 2024
- Published by Allerton Press in Russian Engineering Research
- Vol. 44 (9) , 1240-1243
Improving the Reliability of Pipe End Joints Using Shape Memory
A technology is developed for connecting pipes by means of sleeves or fittings made of materials with shape memory. When using this technology, joints in p
- 1 July 2021
- Published by Allerton Press in Russian Engineering Research
- Vol. 41 (7) , 661-664
Improving the Wear Resistance of Frictional Pairs with Nanostructured Electrospark Coatings
The influence of nanostructuring on the physicomechanical properties of electrospark coatings is assessed. The influence of structural transformations in c
- 1 July 2021
- Published by Allerton Press in Russian Engineering Research
- Vol. 41 (7) , 661-664
Improving the Wear Resistance of Frictional Pairs with Nanostructured Electrospark Coatings
The influence of nanostructuring on the physicomechanical properties of electrospark coatings is assessed. The influence of structural transformations in c
- Open Access
- 30 September 2020
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 30 (3) , 426-447
Evaluation of Technical Condition of Round Gear Hydraulic Pumps of Tractor Mounted Hydraulic Systems
Introduction. In the technical service enterprises, the reliable estimation of a technical condition of hydraulic gear pumps of tractor mounted hydraulic systems is a priority in introducing new repair processes. The absence of data of manufacturing plants on limiting wear of working surfaces of hydraulic pump details, when the decision on repair is taken, leads to the necessity of carrying out additional researches. In this regard, the purpose of work is to find the limit wear values for working surfaces of details of round gear hydraulic pumps. Materials and Methods. The laboratory tests of used round gear hydraulic pumps were carried out according to the method developed in the GOSNITI on the hydraulic bench of the KI-28097M-GOSNITI. The controlled parameter during tests is the pump delivery rate. Results. The results of laboratory bench and micrometer studies of used round gear hydraulic pumps are presented in the work. The mathematical model of pump delivery rate dependence on statistically significant independent factors is obtained. The limit values for wear of working surfaces of round gear hydraulic pump details are determined by the steepest ascent method on the received mathematical model. Discussion and Conclusion. According to the results of the input bench control of the used round gear pumps, 81% of the tested units were operated in the over-extreme limit state. The limit values for wear of working surfaces of round gear hydraulic pump details obtained by the steepest ascent method make it possible to make a conclusion about the necessity of their restoration in repairing at technical service enterprises.
- 30 September 2020
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 30 (3) , 426-447
Open AccessEvaluation of Technical Condition of Round Gear Hydraulic Pumps of Tractor Mounted Hydraulic Systems
Introduction. In the technical service enterprises, the reliable estimation of a technical condition of hydraulic gear pumps of tractor mounted hydraulic systems is a priority in introducing new repair processes. The absence of data of manufacturing plants on limiting wear of working surfaces of hydraulic pump details, when the decision on repair is taken, leads to the necessity of carrying out additional researches. In this regard, the purpose of work is to find the limit wear values for working surfaces of details of round gear hydraulic pumps. Materials and Methods. The laboratory tests of used round gear hydraulic pumps were carried out according to the method developed in the GOSNITI on the hydraulic bench of the KI-28097M-GOSNITI. The controlled parameter during tests is the pump delivery rate. Results. The results of laboratory bench and micrometer studies of used round gear hydraulic pumps are presented in the work. The mathematical model of pump delivery rate dependence on statistically significant independent factors is obtained. The limit values for wear of working surfaces of round gear hydraulic pump details are determined by the steepest ascent method on the received mathematical model. Discussion and Conclusion. According to the results of the input bench control of the used round gear pumps, 81% of the tested units were operated in the over-extreme limit state. The limit values for wear of working surfaces of round gear hydraulic pump details obtained by the steepest ascent method make it possible to make a conclusion about the necessity of their restoration in repairing at technical service enterprises.
- Open Access
- 30 September 2019
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 29 (3) , 396-413
Assessment of Technical Condition of C Series Power Hydraulic Cylinders of Mounted Hydraulic Systems of Tractors
Официальный сайт журнала "Инженерные технологии и системы"
- 30 September 2019
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 29 (3) , 396-413
Open AccessAssessment of Technical Condition of C Series Power Hydraulic Cylinders of Mounted Hydraulic Systems of Tractors
Официальный сайт журнала "Инженерные технологии и системы"