Guilherme Dias
Research Subjects
Guilherme Dias has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Sandra Einloft
Post-Graduation Program in Materials Engineering and Technology
10 shared publications Christophe Le Roux
8 shared publicationsFrançois Martin
7 shared publicationsPierre Micoud
7 shared publicationsManoela Prado
Pontifical Catholic University of Rio Grande do Sul – PUCRS
6 shared publicationsRosane Ligabue
Pontifical Catholic University of Rio Grande do Sul – PUCRS
6 shared publications
Latest Publications
- Open Access
- 17 July 2025
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 64 (30) , 15007-15022
Tailoring Urethane-Based Poly(ionic liquid) Membranes for Enhanced Carbon Dioxide Sorption and Separation Performance
- 17 July 2025
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 64 (30) , 15007-15022
Open AccessTailoring Urethane-Based Poly(ionic liquid) Membranes for Enhanced Carbon Dioxide Sorption and Separation Performance
- 23 April 2019
- Published by Springer Nature in Polymer Bulletin
- Vol. 77 (2) , 975-987
Synthetic talc as catalyst and filler for waterborne polyurethane-based nanocomposite synthesis
- 23 April 2019
- Published by Springer Nature in Polymer Bulletin
- Vol. 77 (2) , 975-987
Synthetic talc as catalyst and filler for waterborne polyurethane-based nanocomposite synthesis
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 22 (suppl 1)
Polyurethane /Ionic Silica Xerogel Composites for CO2 Capture
Capturing carbon dioxide (CO2) from exhaust gases is an important strategy to prevent climate change. There is a great interest in developing novel CO2 sorbents. Thus, a series of polyurethane (PU) / silica xerogels functionalized with RTILs (bmim Cl and bmim TF2N) composites were prepared and characterized. PU matrix was reinforced with functionalized silica xerogels in the range of 0.5-20 wt%. PU / functionalized silica xerogels were characterized by NMR, FTIR, DSC, TGA, DMTA and FESEM. CO2 sorption capacity and reusability were assessed by the pressure-decay technique at 298.15 K and 1 bar. Results showed that the filler aggregation in PU matrix promoted the reduction of mechanical properties. However, addition of silica xerogels functionalized with RTILs in PU matrix led to increased CO2 uptake. CO2 sorption capacity tends to increase with the incorporation of silica xerogels functionalized with RTILs in PU matrix. The best CO2 sorption value was found for PU/SX-[Bmim]-[TF2N] 0.5 composite (48.5 mgCO2/g at 298.15 K and 1 bar). Moreover, the PU/SX-[Bmim]-[TF2N] 0.5 composite showed reuse capacity and higher CO2 sorption value as compared to other reported composites.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 22 (suppl 1)
Open AccessPolyurethane /Ionic Silica Xerogel Composites for CO2 Capture
Capturing carbon dioxide (CO2) from exhaust gases is an important strategy to prevent climate change. There is a great interest in developing novel CO2 sorbents. Thus, a series of polyurethane (PU) / silica xerogels functionalized with RTILs (bmim Cl and bmim TF2N) composites were prepared and characterized. PU matrix was reinforced with functionalized silica xerogels in the range of 0.5-20 wt%. PU / functionalized silica xerogels were characterized by NMR, FTIR, DSC, TGA, DMTA and FESEM. CO2 sorption capacity and reusability were assessed by the pressure-decay technique at 298.15 K and 1 bar. Results showed that the filler aggregation in PU matrix promoted the reduction of mechanical properties. However, addition of silica xerogels functionalized with RTILs in PU matrix led to increased CO2 uptake. CO2 sorption capacity tends to increase with the incorporation of silica xerogels functionalized with RTILs in PU matrix. The best CO2 sorption value was found for PU/SX-[Bmim]-[TF2N] 0.5 composite (48.5 mgCO2/g at 298.15 K and 1 bar). Moreover, the PU/SX-[Bmim]-[TF2N] 0.5 composite showed reuse capacity and higher CO2 sorption value as compared to other reported composites.
- 1 June 2018
- Published by Elsevier in Applied Clay Science
- Vol. 158, 37-45
Synthetic talc as a new platform for producing fluorescent clay polyurethane nanocomposites
- 1 June 2018
- Published by Elsevier in Applied Clay Science
- Vol. 158, 37-45
Synthetic talc as a new platform for producing fluorescent clay polyurethane nanocomposites
- Open Access
- 1 February 2018
- Published by SAGE Publications in Polymers and Polymer Composites
- Vol. 26 (2) , 127-140
Hybrid Pu/Synthetic Talc/Organic Clay Ternary Nanocomposites: Thermal, Mechanical and Morphological Properties
Polyurethane (PU) nanocomposites filled with inorganic particles, aiming at the improvement of mechanical and thermal properties, are well known. Unlike previous work we describe here the combination of two fillers, synthetic talc (silico-metallic mineral particles-SSMMP) with distinct hydrothermal processes (SSMMP 7 h and 24 h) and organically-modified commercial clay (SPR), aiming towards development of new polyurethane ternary nanocomposites by in situ polymerisation. Fillers were added 3 wt.% of the mass of pristine polymer, with a ranging of weight proportions (75:25/25:75) of SSMMP and SPR. Results were compared to those for nanocomposites containing pure SSMMP and SPR fillers. Dispersion degrees and filler interactions with the polyurethane matrix were followed by FTIR, XRD, SEM, TEM and AFM techniques. Results showed that the fillers presented a good dispersion and were exfoliated/ well dispersed in the polyurethane matrix. Thermal and mechanical properties of nanocomposites were evaluated in comparison to the binary nanocomposites (PU/SSMMP 7 h, PU/SSMMP 24 h and PU/ SPR). All nanocomposites presented superior values of Young's modulus to that of pristine PU. Results evidenced that the blend of SSMMP and SPR fillers is an interesting strategy to improve thermal and mechanical properties of nanocomposites.
- 1 February 2018
- Published by SAGE Publications in Polymers and Polymer Composites
- Vol. 26 (2) , 127-140
Open AccessHybrid Pu/Synthetic Talc/Organic Clay Ternary Nanocomposites: Thermal, Mechanical and Morphological Properties
Polyurethane (PU) nanocomposites filled with inorganic particles, aiming at the improvement of mechanical and thermal properties, are well known. Unlike previous work we describe here the combination of two fillers, synthetic talc (silico-metallic mineral particles-SSMMP) with distinct hydrothermal processes (SSMMP 7 h and 24 h) and organically-modified commercial clay (SPR), aiming towards development of new polyurethane ternary nanocomposites by in situ polymerisation. Fillers were added 3 wt.% of the mass of pristine polymer, with a ranging of weight proportions (75:25/25:75) of SSMMP and SPR. Results were compared to those for nanocomposites containing pure SSMMP and SPR fillers. Dispersion degrees and filler interactions with the polyurethane matrix were followed by FTIR, XRD, SEM, TEM and AFM techniques. Results showed that the fillers presented a good dispersion and were exfoliated/ well dispersed in the polyurethane matrix. Thermal and mechanical properties of nanocomposites were evaluated in comparison to the binary nanocomposites (PU/SSMMP 7 h, PU/SSMMP 24 h and PU/ SPR). All nanocomposites presented superior values of Young's modulus to that of pristine PU. Results evidenced that the blend of SSMMP and SPR fillers is an interesting strategy to improve thermal and mechanical properties of nanocomposites.
- 15 December 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (14)
Analyzing the influence of different synthetic talcs in waterborne polyurethane nanocomposites obtainment
Waterborne polyurethane (WPU) nanocomposites were produced utilizing synthetic talc in gel form in order to improve its physical–chemical properties. Synthetic talc manufactured in nano‐gel form are interesting because their interaction with water occurs through hydrogen bonding favoring fillers dispersion within the WPU matrix. WPUs are environmental friendly materials because no organic solvents are used in its production. The nanocomposites obtained with the three synthetic talc nano‐gel fillers presented a good dispersion even when higher amounts of fillers were added, as seen by X‐ray diffraction, transmission electron microscopy, field emission scanning electron microscopy, and atomic force microscopy analyses. The addition of synthetic talcs improved WPU nanocomposites mechanical properties. Storage and loss modulus results proved fillers incorporation into the WPU matrix corroborating with Fourier transform infrared spectroscopy results. Results demonstrated that synthetic talcs in nano‐gel form are interesting to obtain WPU nanocomposites with superior mechanical properties. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46107.
- 15 December 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (14)
Analyzing the influence of different synthetic talcs in waterborne polyurethane nanocomposites obtainment
Waterborne polyurethane (WPU) nanocomposites were produced utilizing synthetic talc in gel form in order to improve its physical–chemical properties. Synthetic talc manufactured in nano‐gel form are interesting because their interaction with water occurs through hydrogen bonding favoring fillers dispersion within the WPU matrix. WPUs are environmental friendly materials because no organic solvents are used in its production. The nanocomposites obtained with the three synthetic talc nano‐gel fillers presented a good dispersion even when higher amounts of fillers were added, as seen by X‐ray diffraction, transmission electron microscopy, field emission scanning electron microscopy, and atomic force microscopy analyses. The addition of synthetic talcs improved WPU nanocomposites mechanical properties. Storage and loss modulus results proved fillers incorporation into the WPU matrix corroborating with Fourier transform infrared spectroscopy results. Results demonstrated that synthetic talcs in nano‐gel form are interesting to obtain WPU nanocomposites with superior mechanical properties. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46107.
- 21 September 2016
- Published by Wiley in Macromolecular Symposia
- Vol. 367 (1) , 136-142
Comparing Different Synthetic Talc as Fillers for Polyurethane Nanocomposites
Summary: This work presents the syntheses of PU nanocomposites, by in situ polymerization technique, using different synthetic talcs as inorganic filler. The fillers were obtained from two different hydrothermal treatments and composition (talc‐Mg and talc‐Ni). For nanocomposites syntheses 3% w/w of synthetic talc were added related to the weight of pure polymer. Samples were characterized by Fourier Transform Infrared Spectroscopy (FTIR), X‐Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA) to understand the influence of the fillers syntheses and composition in morphological and thermal properties of the obtained nanocomposites. When talc‐Ni was used as filler, the resulting nanocomposite was intercalated while with talc‐Mg was exfoliated into the polyurethane matrix. Both fillers have increased the thermal properties of the polymer, but the exfoliated nanocomposite provided higher thermal stability.
- 21 September 2016
- Published by Wiley in Macromolecular Symposia
- Vol. 367 (1) , 136-142
Comparing Different Synthetic Talc as Fillers for Polyurethane Nanocomposites
Summary: This work presents the syntheses of PU nanocomposites, by in situ polymerization technique, using different synthetic talcs as inorganic filler. The fillers were obtained from two different hydrothermal treatments and composition (talc‐Mg and talc‐Ni). For nanocomposites syntheses 3% w/w of synthetic talc were added related to the weight of pure polymer. Samples were characterized by Fourier Transform Infrared Spectroscopy (FTIR), X‐Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA) to understand the influence of the fillers syntheses and composition in morphological and thermal properties of the obtained nanocomposites. When talc‐Ni was used as filler, the resulting nanocomposite was intercalated while with talc‐Mg was exfoliated into the polyurethane matrix. Both fillers have increased the thermal properties of the polymer, but the exfoliated nanocomposite provided higher thermal stability.
- 14 July 2015
- Published by Springer Nature in Polymer Bulletin
- Vol. 72 (11) , 2991-3006
Synthetic silico-metallic mineral particles (SSMMP) as nanofillers: comparing the effect of different hydrothermal treatments on the PU/SSMMP nanocomposites properties
- 14 July 2015
- Published by Springer Nature in Polymer Bulletin
- Vol. 72 (11) , 2991-3006
Synthetic silico-metallic mineral particles (SSMMP) as nanofillers: comparing the effect of different hydrothermal treatments on the PU/SSMMP nanocomposites properties
- 29 December 2014
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (16)
Synthetic Ni‐talc as filler for producing polyurethane nanocomposites
New synthetic Ni‐talc was used as filler in the synthesis of polyurethane (PU) nanocomposites by in situ polymerization and to emphasize the contribution of the new material compared with natural talc. Good dispersion of Ni‐talc was supported by homogeneous green coloration observed in the polymer matrix. X‐ray diffraction (XRD) analyses indicate the intercalation of polymeric matrix into the filler layers by the increase in d001‐spacing value of the Ni‐talc for the nanocomposites when compared to the pristine filler. The nanocomposites obtained with synthetic talc showed an improvement in the crystallization temperature and in thermal stability when compared to pure PU and the composite obtained with natural talc. The young modulus of PU/talc materials containing both Ni‐talc and natural talc were slight higher than pure PU. As shown by scanning electron microscope (SEM), Ni‐talc fillers were well dispersed into the polymeric matrix probably due to the good compatibility of both phases filler/polymer mainly achieved by the filler OH interaction with the urethane group of the polymeric chain. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 41854.
- 29 December 2014
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (16)
Synthetic Ni‐talc as filler for producing polyurethane nanocomposites
New synthetic Ni‐talc was used as filler in the synthesis of polyurethane (PU) nanocomposites by in situ polymerization and to emphasize the contribution of the new material compared with natural talc. Good dispersion of Ni‐talc was supported by homogeneous green coloration observed in the polymer matrix. X‐ray diffraction (XRD) analyses indicate the intercalation of polymeric matrix into the filler layers by the increase in d001‐spacing value of the Ni‐talc for the nanocomposites when compared to the pristine filler. The nanocomposites obtained with synthetic talc showed an improvement in the crystallization temperature and in thermal stability when compared to pure PU and the composite obtained with natural talc. The young modulus of PU/talc materials containing both Ni‐talc and natural talc were slight higher than pure PU. As shown by scanning electron microscope (SEM), Ni‐talc fillers were well dispersed into the polymeric matrix probably due to the good compatibility of both phases filler/polymer mainly achieved by the filler OH interaction with the urethane group of the polymeric chain. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 41854.