Babak Nasr
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Babak Nasr has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Andrea R. Ferro
Department of Civil and Environmental Engineering, Clarkson University
2 shared publications - Goodarz Ahmadi
Department of Mechanical and Aerospace Engineering, Clarkson University, Potsdam, NY 13699, USA
2 shared publications - Suresh Dhaniyala
Mechanical and Aeronautical Engineering, Clarkson University, Potsdam, NY, USA
2 shared publications
Latest Publications
- 2 December 2019
- Published by Taylor & Francis in Aerosol Science and Technology
- Vol. 54 (3) , 291-303
A model for particle removal from surfaces with large-scale roughness in turbulent flows
The resuspension rate of particles from surfaces is significantly dependent on surface roughness. Existing models only consider the case of surface asperities much smaller than particle diameter, but often particle sizes of interest are comparable or smaller than substrate roughness. In this study, a model for particle removal from large-scale roughness is described. Substrate roughness is described using a 2D sinusoidal profile. The critical shear velocity is determined considering rolling detachment of particles with JKR adhesion model and hydrodynamic moments on particles residing on the rough substrates. Our model results show that the effect of surface roughness on critical shear velocity is strongly dependent on the value of roughness amplitude and wavelength relative to particle size. The model predicts four primary removal regions based on relative particle-surface characteristics: easier-to-remove than smooth substrate, more difficult to remove than smooth substrate, not possible to remove, and similar behavior as smooth surface. The model performance is validated by comparison of predictions with published experimental results for highly rough substrates.
- 2 December 2019
- Published by Taylor & Francis in Aerosol Science and Technology
- Vol. 54 (3) , 291-303
A model for particle removal from surfaces with large-scale roughness in turbulent flows
The resuspension rate of particles from surfaces is significantly dependent on surface roughness. Existing models only consider the case of surface asperities much smaller than particle diameter, but often particle sizes of interest are comparable or smaller than substrate roughness. In this study, a model for particle removal from large-scale roughness is described. Substrate roughness is described using a 2D sinusoidal profile. The critical shear velocity is determined considering rolling detachment of particles with JKR adhesion model and hydrodynamic moments on particles residing on the rough substrates. Our model results show that the effect of surface roughness on critical shear velocity is strongly dependent on the value of roughness amplitude and wavelength relative to particle size. The model predicts four primary removal regions based on relative particle-surface characteristics: easier-to-remove than smooth substrate, more difficult to remove than smooth substrate, not possible to remove, and similar behavior as smooth surface. The model performance is validated by comparison of predictions with published experimental results for highly rough substrates.
- 13 September 2019
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 33 (24) , 2631-2660
Overview of mechanistic particle resuspension models: comparison with compilation of experimental data
In this study, several mechanistic models for particle removal from substrates were introduced and their predictive ability was tested. Empirically optimized parameters for a selected set of particle-substrate combinations were obtained and the ability of these models to predict resuspension for a large number of particle-substrate combinations and flow conditions using the published experimental data was explored. Our analysis showed that accurate predictions for a broad spectrum of particle-substrate combinations require accounting for substrate roughness and particle non-sphericity. From analysis of our compiled experimental data set, it was determined that the shear velocities required for particle resuspension follow a log-normal distribution, with geometric standard deviations in the range of 1.4 to 1.7. From comparison of the calculated and measured critical shear velocities, we found that a critical roughness parameter value of Δc = 0.774 is a reasonable estimate for most real substrates. We show that the combination of parameters determined from our study and models that account for roughness and particle non-sphericity, it is possible to predict particle resuspension from most substrates with reasonable accuracy.
- 13 September 2019
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 33 (24) , 2631-2660
Overview of mechanistic particle resuspension models: comparison with compilation of experimental data
In this study, several mechanistic models for particle removal from substrates were introduced and their predictive ability was tested. Empirically optimized parameters for a selected set of particle-substrate combinations were obtained and the ability of these models to predict resuspension for a large number of particle-substrate combinations and flow conditions using the published experimental data was explored. Our analysis showed that accurate predictions for a broad spectrum of particle-substrate combinations require accounting for substrate roughness and particle non-sphericity. From analysis of our compiled experimental data set, it was determined that the shear velocities required for particle resuspension follow a log-normal distribution, with geometric standard deviations in the range of 1.4 to 1.7. From comparison of the calculated and measured critical shear velocities, we found that a critical roughness parameter value of Δc = 0.774 is a reasonable estimate for most real substrates. We show that the combination of parameters determined from our study and models that account for roughness and particle non-sphericity, it is possible to predict particle resuspension from most substrates with reasonable accuracy.