Rajib Kumar Biswas
Research Subjects
Rajib Kumar Biswas has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Mitsuyasu Iwanami
Tokyo Institute of Technology
3 shared publicationsTakahiro Saito
3 shared publications- Farabi Bin Ahmed
Ahsanullah University of Science and Technology
2 shared publications - Mitsuyasu Iwanami
Tokyo Institute of Technology
2 shared publications - Nobuhiro Chijiwa
Tokyo Institute of Technology
2 shared publications - Takahiro Saito
Technical Research Institute, Okumura Corporation, Tsukuba, Japan
2 shared publications
Latest Publications
- Open Access
- 31 May 2024
- Published by MDPI AG in Construction Materials
- Vol. 4 (2) , 468-492
Flexural and Shear Strengthening of Reinforced-Concrete Beams with Ultra-High-Performance Concrete (UHPC)
Ultra-high-performance concrete (UHPC) is considered to be a promising material for the strengthening of damaged reinforced concrete (RC) members due to its high mechanical strength and low permeability. However, its high material cost, limited code provisions, and scattered material properties limit its wide application. There is a great need to review existing articles and create a database to assist different technical committees for future code provisions on UHPC. This study presents a comprehensive overview focusing on the effect of the UHPC layer on the flexural and shear strengthening of RC beams. From this review, it was evident that (1) different retrofitting configurations have a remarkable effect on the cracking moment compared to the maximum moment in the case of flexural strengthening; (2) the ratios of the shear span and UHPC layer thickness have a notable effect on shear strengthening and the failure mode; and (3) different bonding techniques have insignificant effects on shear strengthening but a positive impact on flexural strengthening. Overall, it can be concluded that three-side strengthening has a higher increment range for flexural (maximum, 81%–120%; cracking, 300%–500%) and shear (maximum, 51%–80%; cracking, 121%–180%) strengthening. From this literature review, an experimental database was established, and different failure modes were identified. Finally, this research highlights current issues with UHPC and recommends some future works.
- 31 May 2024
- Published by MDPI AG in Construction Materials
- Vol. 4 (2) , 468-492
Open AccessFlexural and Shear Strengthening of Reinforced-Concrete Beams with Ultra-High-Performance Concrete (UHPC)
Ultra-high-performance concrete (UHPC) is considered to be a promising material for the strengthening of damaged reinforced concrete (RC) members due to its high mechanical strength and low permeability. However, its high material cost, limited code provisions, and scattered material properties limit its wide application. There is a great need to review existing articles and create a database to assist different technical committees for future code provisions on UHPC. This study presents a comprehensive overview focusing on the effect of the UHPC layer on the flexural and shear strengthening of RC beams. From this review, it was evident that (1) different retrofitting configurations have a remarkable effect on the cracking moment compared to the maximum moment in the case of flexural strengthening; (2) the ratios of the shear span and UHPC layer thickness have a notable effect on shear strengthening and the failure mode; and (3) different bonding techniques have insignificant effects on shear strengthening but a positive impact on flexural strengthening. Overall, it can be concluded that three-side strengthening has a higher increment range for flexural (maximum, 81%–120%; cracking, 300%–500%) and shear (maximum, 51%–80%; cracking, 121%–180%) strengthening. From this literature review, an experimental database was established, and different failure modes were identified. Finally, this research highlights current issues with UHPC and recommends some future works.
- 11 November 2023
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 8 (12) , 1-13
Structural behavior of severely corroded RC beams retrofitted with UHPC layer: an experimental study
- 11 November 2023
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 8 (12) , 1-13
Structural behavior of severely corroded RC beams retrofitted with UHPC layer: an experimental study
- Open Access
- 26 October 2023
- Published by Springer Nature in Research Square
Structural behavior of severely corroded RC beams retrofitted with UHPC layer - experimental study and numerical analysis
Corrosion of reinforcement bars in reinforced concrete (RC) structures is considered a major concern. This study examines the flexural response of severely corroded RC beams retrofitted with ultra-high performance fiber reinforced concrete (UHPC) layer. UHPC layers were attached to the concrete substrate in four different configurations to investigate whether they could strengthen severely corroded RC beams. To represent carbonation-induced uniform corrosion, artificial corrosion was adopted in this study by replacing the deformed bars with plain bars and reducing the cross-sectional area. The plain steel bars represented about 38% of rebar corrosion. Obtained results revealed that UHPC layers can remarkably enhance the structural performance when it comes to serviceability and ultimate limit state. The test results also revealed that RC beams retrofitted with the UHPC layer might be unable to improve the displacement capacity of the corroded RC beam owing to bond deterioration between the concrete and embedded rebars and reduced cross-sectional area. Finally, a simplified numerical model was developed in this study and validated with the experimental results.
- 26 October 2023
- Published by Springer Nature in Research Square
Open AccessStructural behavior of severely corroded RC beams retrofitted with UHPC layer - experimental study and numerical analysis
Corrosion of reinforcement bars in reinforced concrete (RC) structures is considered a major concern. This study examines the flexural response of severely corroded RC beams retrofitted with ultra-high performance fiber reinforced concrete (UHPC) layer. UHPC layers were attached to the concrete substrate in four different configurations to investigate whether they could strengthen severely corroded RC beams. To represent carbonation-induced uniform corrosion, artificial corrosion was adopted in this study by replacing the deformed bars with plain bars and reducing the cross-sectional area. The plain steel bars represented about 38% of rebar corrosion. Obtained results revealed that UHPC layers can remarkably enhance the structural performance when it comes to serviceability and ultimate limit state. The test results also revealed that RC beams retrofitted with the UHPC layer might be unable to improve the displacement capacity of the corroded RC beam owing to bond deterioration between the concrete and embedded rebars and reduced cross-sectional area. Finally, a simplified numerical model was developed in this study and validated with the experimental results.
- Open Access
- 12 August 2022
- Published by Elsevier in Developments in the Built Environment
- Vol. 12
A simplified approach to evaluate cyclic response and seismic fragility of corrosion damaged RC bridge piers
- 12 August 2022
- Published by Elsevier in Developments in the Built Environment
- Vol. 12
Open AccessA simplified approach to evaluate cyclic response and seismic fragility of corrosion damaged RC bridge piers
- Open Access
- 21 July 2021
- Published by MDPI AG in Applied Mechanics
- Vol. 2 (3) , 501-515
Effects of Steel Fiber Percentage and Aspect Ratios on Fresh and Harden Properties of Ultra-High Performance Fiber Reinforced Concrete
Steel fibers and their aspect ratios are important parameters that have significant influence on the mechanical properties of ultrahigh-performance fiber-reinforced concrete (UHPFRC). Steel fiber dosage also significantly contributes to the initial manufacturing cost of UHPFRC. This study presents a comprehensive literature review of the effects of steel fiber percentages and aspect ratios on the setting time, workability, and mechanical properties of UHPFRC. It was evident that (1) an increase in steel fiber dosage and aspect ratio negatively impacted workability, owing to the interlocking between fibers; (2) compressive strength was positively influenced by the steel fiber dosage and aspect ratio; and (3) a faster loading rate significantly improved the mechanical properties. There were also some shortcomings in the measurement method for setting time. Lastly, this research highlights current issues for future research. The findings of the study are useful for practicing engineers to understand the distinctive characteristics of UHPFRC.
- 21 July 2021
- Published by MDPI AG in Applied Mechanics
- Vol. 2 (3) , 501-515
Open AccessEffects of Steel Fiber Percentage and Aspect Ratios on Fresh and Harden Properties of Ultra-High Performance Fiber Reinforced Concrete
Steel fibers and their aspect ratios are important parameters that have significant influence on the mechanical properties of ultrahigh-performance fiber-reinforced concrete (UHPFRC). Steel fiber dosage also significantly contributes to the initial manufacturing cost of UHPFRC. This study presents a comprehensive literature review of the effects of steel fiber percentages and aspect ratios on the setting time, workability, and mechanical properties of UHPFRC. It was evident that (1) an increase in steel fiber dosage and aspect ratio negatively impacted workability, owing to the interlocking between fibers; (2) compressive strength was positively influenced by the steel fiber dosage and aspect ratio; and (3) a faster loading rate significantly improved the mechanical properties. There were also some shortcomings in the measurement method for setting time. Lastly, this research highlights current issues for future research. The findings of the study are useful for practicing engineers to understand the distinctive characteristics of UHPFRC.