Chintamani Vyjayanthi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chintamani Vyjayanthi has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ajit Muzumdar
National Institute of Technology Goa
5 shared publications - Chirag Modi
NIT Goa
5 shared publications - Madhu Gopahanal Manjunath
National Institute of Technology Goa
4 shared publications Chirag Modi
2 shared publicationsAlok Jaiswal
National Institute of Technology Goa
1 shared publication- Nivedita Naik
Department of Electrical and Electronics Engineering, National Institute of Technology Goa, Ponda, Goa, India
1 shared publication
Latest Publications
- 19 May 2024
- Published by Springer Nature
- p. 169-181
Modelling and Simulation of DC-DC Converters for PEM Fuel Cell Electric Vehicles
- 19 May 2024
- Published by Springer Nature
- p. 169-181
Modelling and Simulation of DC-DC Converters for PEM Fuel Cell Electric Vehicles
- Open Access
- 17 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 74277-74289
Filter-Based Active Damping of DAB Converter to Lower Battery Degradation in EV Fast Charging Application
Dual Active Bridge (DAB) converter is well suited for off-board fast Electric Vehicle Charging Stations (EVCS) and in DC microgrid-connected EVCS applications. However, proper modification in DAB converter topology is crucial for fast charging, as the charging current is very high, and any oscillations would shorten the EV battery life. As per literature, DAB converter topology integrated with a series inductor at the output for EV battery charging reduces the output current ripple by 40%. However, as per our observation, potentially unstable dynamics are introduced in the system with the inclusion of an LC filter. This affects the controller stability; hence, these dynamics must be damped using active or passive damping. Passive damping is less efficient due to the considerable losses it produces, partly induced by low-frequency noise and partly from switching-frequency noise. Also, placing the damping at the selective resonant frequency is very complex. In comparison, active damping offers selective placement and loss reduction. This paper presents the DAB converter mathematical modeling using the generalized average model (GAM) and the average output current linearization model (AOCLM). The paper presents stability analysis and proposes a novel and robust approach to control the dynamics in the current and voltage control loops during EV charging, thereby reducing battery degradation. The charge flow to the battery is controlled using Constant Current Constant Voltage (CCCV) algorithm. The proposed scheme also eliminates the need for extra sensors by selectively attenuating the oscillations at the frequency of interest. The performance of the proposed model for EV fast charging application is verified using MATLAB/Simulink and experimentally validated in a real-time simulator OPAL-RT hardware platform.
- 17 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 74277-74289
Open AccessFilter-Based Active Damping of DAB Converter to Lower Battery Degradation in EV Fast Charging Application
Dual Active Bridge (DAB) converter is well suited for off-board fast Electric Vehicle Charging Stations (EVCS) and in DC microgrid-connected EVCS applications. However, proper modification in DAB converter topology is crucial for fast charging, as the charging current is very high, and any oscillations would shorten the EV battery life. As per literature, DAB converter topology integrated with a series inductor at the output for EV battery charging reduces the output current ripple by 40%. However, as per our observation, potentially unstable dynamics are introduced in the system with the inclusion of an LC filter. This affects the controller stability; hence, these dynamics must be damped using active or passive damping. Passive damping is less efficient due to the considerable losses it produces, partly induced by low-frequency noise and partly from switching-frequency noise. Also, placing the damping at the selective resonant frequency is very complex. In comparison, active damping offers selective placement and loss reduction. This paper presents the DAB converter mathematical modeling using the generalized average model (GAM) and the average output current linearization model (AOCLM). The paper presents stability analysis and proposes a novel and robust approach to control the dynamics in the current and voltage control loops during EV charging, thereby reducing battery degradation. The charge flow to the battery is controlled using Constant Current Constant Voltage (CCCV) algorithm. The proposed scheme also eliminates the need for extra sensors by selectively attenuating the oscillations at the frequency of interest. The performance of the proposed model for EV fast charging application is verified using MATLAB/Simulink and experimentally validated in a real-time simulator OPAL-RT hardware platform.
- 8 April 2022
- Published by Springer Nature
- p. 1-15
NITG Chain: A Scalable, Private and Permissioned Blockchain with Proof of Reputation Consensus Method
- 8 April 2022
- Published by Springer Nature
- p. 1-15
NITG Chain: A Scalable, Private and Permissioned Blockchain with Proof of Reputation Consensus Method
- 19 March 2022
- Published by Elsevier in Journal of Cleaner Production
- Vol. 349
A permissioned blockchain enabled trustworthy and incentivized emission trading system
- 19 March 2022
- Published by Elsevier in Journal of Cleaner Production
- Vol. 349
A permissioned blockchain enabled trustworthy and incentivized emission trading system
- 24 February 2022
- Published by Elsevier in Electric Power Systems Research
- Vol. 207
Designing a blockchain-enabled privacy-preserving energy theft detection system for smart grid neighborhood area network
- 24 February 2022
- Published by Elsevier in Electric Power Systems Research
- Vol. 207
Designing a blockchain-enabled privacy-preserving energy theft detection system for smart grid neighborhood area network
- Open Access
- 7 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 96995-97009
Investigation on Effect of Irradiance Change in Maximum Power Extraction From PV Array Interconnection Schemes During Partial Shading Conditions
This paper presents the effect of irradiance change in solar photovoltaic (PV) array interconnection schemes under partial shading conditions (PSCs) for optimal selection of PV interconnection schemes in order to extract maximum power (MP) from the PV array. A 4×4 PV array is considered to examine the well-known PV interconnection schemes under different shading scenarios at distinct irradiance conditions. Simulation studies and experimental verification are carried out by considering a 30 W PV panel to analyse the performance of the PV array under various dynamic conditions. Comprehensive analysis in terms of fill factor, output power and mismatching power loss is presented by considering different interconnection schemes under various shading scenarios and irradiance levels. From the simulation studies and experimental verification, it is observed that the irradiance magnitude has a significant impact on the PV power generation from array interconnection schemes under PSCs wherein the performance characteristics of the array interconnection schemes vary with the variation in irradiance levels. It is also identified that the irradiance factor needs to be considered as a design variable while selecting the optimal PV array interconnection schemes for maximum power extraction under PSCs.
- 7 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 96995-97009
Open AccessInvestigation on Effect of Irradiance Change in Maximum Power Extraction From PV Array Interconnection Schemes During Partial Shading Conditions
This paper presents the effect of irradiance change in solar photovoltaic (PV) array interconnection schemes under partial shading conditions (PSCs) for optimal selection of PV interconnection schemes in order to extract maximum power (MP) from the PV array. A 4×4 PV array is considered to examine the well-known PV interconnection schemes under different shading scenarios at distinct irradiance conditions. Simulation studies and experimental verification are carried out by considering a 30 W PV panel to analyse the performance of the PV array under various dynamic conditions. Comprehensive analysis in terms of fill factor, output power and mismatching power loss is presented by considering different interconnection schemes under various shading scenarios and irradiance levels. From the simulation studies and experimental verification, it is observed that the irradiance magnitude has a significant impact on the PV power generation from array interconnection schemes under PSCs wherein the performance characteristics of the array interconnection schemes vary with the variation in irradiance levels. It is also identified that the irradiance factor needs to be considered as a design variable while selecting the optimal PV array interconnection schemes for maximum power extraction under PSCs.
- 1 June 2021
- Published by Elsevier in Journal of Network and Computer Applications
- Vol. 183-184
A trustworthy and incentivized smart grid energy trading framework using distributed ledger and smart contracts
- 1 June 2021
- Published by Elsevier in Journal of Network and Computer Applications
- Vol. 183-184
A trustworthy and incentivized smart grid energy trading framework using distributed ledger and smart contracts
- 10 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Systems Journal
- Vol. 16 (2) , 2448-2459
Designing a Robust and Accurate Model for Consumer-Centric Short-Term Load Forecasting in Microgrid Environment
The consumer’s short-term load forecasting plays an essential role in microgrid energy distribution. However, the load forecasting at consumer level is more challenging than at substation level due to high volatility and uncertainty in energy consumption. In literature, many machine learning-based forecasting models have been explored. However, there is a need of developing a robust and accurate model to handle highly inconsistent energy consumption. In this article, we propose a robust and accurate model for consumer’s short-term load forecasting, which uses feasible techniques such as random forest, support vector regressor, and long short-term memory as base predictors to handle varying traits of energy consumption. For the final decision-making on forecasting result of these predictors, it assigns weights to each predictor dynamically as per the forecasting efficacy. The proposed model is tested on different consumer’s varying traits of energy consumption. The experimental results show that the proposed model achieves forecasting error reduction by 3.46 and 2.53 in terms of average RMSE and MAE, respectively, in comparison with the existing models. It is robust and accurate even in presence of highly volatile and uncertain load patterns, and thus, it can better fit for microgrid energy management.
- 10 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Systems Journal
- Vol. 16 (2) , 2448-2459
Designing a Robust and Accurate Model for Consumer-Centric Short-Term Load Forecasting in Microgrid Environment
The consumer’s short-term load forecasting plays an essential role in microgrid energy distribution. However, the load forecasting at consumer level is more challenging than at substation level due to high volatility and uncertainty in energy consumption. In literature, many machine learning-based forecasting models have been explored. However, there is a need of developing a robust and accurate model to handle highly inconsistent energy consumption. In this article, we propose a robust and accurate model for consumer’s short-term load forecasting, which uses feasible techniques such as random forest, support vector regressor, and long short-term memory as base predictors to handle varying traits of energy consumption. For the final decision-making on forecasting result of these predictors, it assigns weights to each predictor dynamically as per the forecasting efficacy. The proposed model is tested on different consumer’s varying traits of energy consumption. The experimental results show that the proposed model achieves forecasting error reduction by 3.46 and 2.53 in terms of average RMSE and MAE, respectively, in comparison with the existing models. It is robust and accurate even in presence of highly volatile and uncertain load patterns, and thus, it can better fit for microgrid energy management.
- 1 August 2019
- Published by Walter de Gruyter GmbH in International Journal of Emerging Electric Power Systems
- Vol. 20 (4)
PV-Battery Hybrid System with Less AH Capacity for Standalone DC Loads
Partial Shading Condition (PSC) is one of the key issues faced by Solar Photovoltaic (PV) systems. PSCs mainly occur due to clouds, shadows of trees/buildings, dust and so on. During the PSC, the shaded PV module acts like a sink and absorbs the power from highest irradiated modules in a string and leads to hotspot. This situation is highly vulnerable and has to be avoided. Bypass diodes are used in series configured PV modules to overcome the hotspot effect caused due to PSC. However, the use of bypass diodes leads to multiple peaks in the Power-Voltage (P-V) graph of a PV array. One among them is Global peak point, where PV array needs to operate under PSC. In such a case, some amount of power generated by the shaded modules gets wasted, which will lead to poor performance and efficiency of the overall system. Moreover, for standalone DC load applications an auxiliary supply also required to provide reliable supply to the load during night times and PSC. Normally, batteries are used in standalone systems as an auxiliary supply. To control the charging and discharging process of battery a bi-directional DC-DC converter is used as a charge/discharge controller. The amount of power that is being charged/discharged by batteries depends upon the load requirement and solar power availability. Under PSC, due to lack of extraction of PV power from shaded modules, batteries have to supply the deficient power to the load. This situation forces to increase the AH capacity of the battery to provide reliable supply. In this research article PV-Battery Hybrid system is proposed to improve the performance of PV under varying irradiance and load conditions with reduced AH capacity of battery for standalone DC loads. The performance assessment of proposed topology has been carried out with the comparison of percentage improvement in power extraction, percentage reduction in the average current consumption of battery and SoC delivered by battery with conventional methodologies of bypass diode and proposed methodology under PSC. The assessment is carried out on MATLAB/SIMULINK and results are presented.
- 1 August 2019
- Published by Walter de Gruyter GmbH in International Journal of Emerging Electric Power Systems
- Vol. 20 (4)
PV-Battery Hybrid System with Less AH Capacity for Standalone DC Loads
Partial Shading Condition (PSC) is one of the key issues faced by Solar Photovoltaic (PV) systems. PSCs mainly occur due to clouds, shadows of trees/buildings, dust and so on. During the PSC, the shaded PV module acts like a sink and absorbs the power from highest irradiated modules in a string and leads to hotspot. This situation is highly vulnerable and has to be avoided. Bypass diodes are used in series configured PV modules to overcome the hotspot effect caused due to PSC. However, the use of bypass diodes leads to multiple peaks in the Power-Voltage (P-V) graph of a PV array. One among them is Global peak point, where PV array needs to operate under PSC. In such a case, some amount of power generated by the shaded modules gets wasted, which will lead to poor performance and efficiency of the overall system. Moreover, for standalone DC load applications an auxiliary supply also required to provide reliable supply to the load during night times and PSC. Normally, batteries are used in standalone systems as an auxiliary supply. To control the charging and discharging process of battery a bi-directional DC-DC converter is used as a charge/discharge controller. The amount of power that is being charged/discharged by batteries depends upon the load requirement and solar power availability. Under PSC, due to lack of extraction of PV power from shaded modules, batteries have to supply the deficient power to the load. This situation forces to increase the AH capacity of the battery to provide reliable supply. In this research article PV-Battery Hybrid system is proposed to improve the performance of PV under varying irradiance and load conditions with reduced AH capacity of battery for standalone DC loads. The performance assessment of proposed topology has been carried out with the comparison of percentage improvement in power extraction, percentage reduction in the average current consumption of battery and SoC delivered by battery with conventional methodologies of bypass diode and proposed methodology under PSC. The assessment is carried out on MATLAB/SIMULINK and results are presented.