Edward J. Hoppe
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Edward J. Hoppe has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
Andrea Vaccari
3 shared publicationsBrian Bruckno
3 shared publicationsScott T. Acton
Charles L. Brown Department of Electrical and Computer Engineering, University of Virginia, Charlottesville, VA
3 shared publicationsBrian S. Bruckno
Virginia Department of Transportation, Staunton, VA
2 shared publicationsElizabeth Campbell
2 shared publicationsMichael Stuecheli
2 shared publications
Latest Publications
- Open Access
- 9 May 2020
- Published by MDPI AG in Remote Sensing
- Vol. 12  (9) , 1507
Studying the Applicability of X-Band SAR Data to the Network-Scale Mapping of Pavement Roughness on US Roads
The traveling public judges the quality of a road mostly by its roughness and/or ride quality. Hence, mapping, monitoring, and maintaining adequate pavement smoothness is of high importance to State Departments of Transportation in the US. Current methods rely mostly on in situ measurements and are, therefore, time consuming and costly when applied at the network scale. This paper studies the applicability of satellite radar remote sensing data, specifically, high-resolution Synthetic Aperture Radar (SAR) data acquired at X-band, to the network-wide mapping of pavement roughness of roads in the US. Based on a comparison of high-resolution X-band Cosmo-SkyMed images with road roughness data in the form of International Roughness Index (IRI) measurements, we found that X-band radar brightness generally increases when pavement roughness worsens. Based on these findings, we developed and inverted a model to distinguish well maintained road segments from segments in need of repair. Over test sites in Augusta County, VA, we found that our classification scheme reaches an overall accuracy of 92.6%. This study illustrates the capacity of X-band SAR for pavement roughness mapping and suggests that incorporating SAR into DOT operations could be beneficial.
- 9 May 2020
- Published by MDPI AG in Remote Sensing
- Vol. 12  (9) , 1507
Open AccessStudying the Applicability of X-Band SAR Data to the Network-Scale Mapping of Pavement Roughness on US Roads
The traveling public judges the quality of a road mostly by its roughness and/or ride quality. Hence, mapping, monitoring, and maintaining adequate pavement smoothness is of high importance to State Departments of Transportation in the US. Current methods rely mostly on in situ measurements and are, therefore, time consuming and costly when applied at the network scale. This paper studies the applicability of satellite radar remote sensing data, specifically, high-resolution Synthetic Aperture Radar (SAR) data acquired at X-band, to the network-wide mapping of pavement roughness of roads in the US. Based on a comparison of high-resolution X-band Cosmo-SkyMed images with road roughness data in the form of International Roughness Index (IRI) measurements, we found that X-band radar brightness generally increases when pavement roughness worsens. Based on these findings, we developed and inverted a model to distinguish well maintained road segments from segments in need of repair. Over test sites in Augusta County, VA, we found that our classification scheme reaches an overall accuracy of 92.6%. This study illustrates the capacity of X-band SAR for pavement roughness mapping and suggests that incorporating SAR into DOT operations could be beneficial.
- Open Access
- 23 February 2020
- Published by MDPI AG in ISPRS International Journal of Geo-Information
- Vol. 9  (2) , 131
Slope Hazard Monitoring Using High-Resolution Satellite Remote Sensing: Lessons Learned from a Case Study
In this study, a highway slope monitoring project for a section of US highway I-77 in Virginia was carried out with the InSAR technique. This paper attempts to provide insights into the complete and practical solution for the monitoring project, including two parts: what to consider for selecting the optimal satellites and configurations for the given area of interest (AoI) and budget; and how to best process the selected data for the monitoring purposes. To answer the first question, the simulated geometric distortion map, cumulative change detection map, intensity map, interferograms and coherence maps from all available historical datasets were generated. The satellite configuration that gives the best coherence and least geometric distortion with the given budget was selected for the monitoring project. For this project, it was the X-band COSMO stripmap with 3 m resolution and eight-days revisit time. To answer the second question, a multi-temporal InSAR (MTInSAR) was applied to retrieve the settlement time series of the slopes along the highway. Several special techniques were applied to increase the level of confidence, i.e., dividing AoI into smaller and independent areas, using a non-linear approach, etc. Finally, fieldwork was carried out for the interpretation and validation of the results. The AoI was overall stable, though some local changes were detected by the SAR signal which were validated by the fieldwork.
- 23 February 2020
- Published by MDPI AG in ISPRS International Journal of Geo-Information
- Vol. 9  (2) , 131
Open AccessSlope Hazard Monitoring Using High-Resolution Satellite Remote Sensing: Lessons Learned from a Case Study
In this study, a highway slope monitoring project for a section of US highway I-77 in Virginia was carried out with the InSAR technique. This paper attempts to provide insights into the complete and practical solution for the monitoring project, including two parts: what to consider for selecting the optimal satellites and configurations for the given area of interest (AoI) and budget; and how to best process the selected data for the monitoring purposes. To answer the first question, the simulated geometric distortion map, cumulative change detection map, intensity map, interferograms and coherence maps from all available historical datasets were generated. The satellite configuration that gives the best coherence and least geometric distortion with the given budget was selected for the monitoring project. For this project, it was the X-band COSMO stripmap with 3 m resolution and eight-days revisit time. To answer the second question, a multi-temporal InSAR (MTInSAR) was applied to retrieve the settlement time series of the slopes along the highway. Several special techniques were applied to increase the level of confidence, i.e., dividing AoI into smaller and independent areas, using a non-linear approach, etc. Finally, fieldwork was carried out for the interpretation and validation of the results. The AoI was overall stable, though some local changes were detected by the SAR signal which were validated by the fieldwork.
- 1 December 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 24  (12)
Deformation Monitoring of Posttensioned Bridges Using High-Resolution Satellite Remote Sensing
This study presents the results of spaceborne monitoring of two posttensioned bridges in Virginia. Routine safety inspections revealed extensive cracking in the concrete girders. Problems were traced to the inadequate quality of tendon grouting, resulting in the partially bonded condition. The TerraSAR-X radar satellite, operated by the German Aerospace Center, was used to acquire radar imagery in the Staring SpotLight mode from the ascending and descending orbits at 11-day intervals. The data were processed with the SqueeSAR algorithm, resulting in millimeter-range precision of the time-displacement series. No permanent deformations were detected at the posttensioned segments during the monitoring period of 1.3 years. The high density of the measurement points allowed adequate characterization of bridge displacements. The results of the interferometric analysis attest to the feasibility of implementing satellite-based performance monitoring of bridges, offering an innovative asset management tool that can complement and augment current inspection methods.
- 1 December 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 24  (12)
Deformation Monitoring of Posttensioned Bridges Using High-Resolution Satellite Remote Sensing
This study presents the results of spaceborne monitoring of two posttensioned bridges in Virginia. Routine safety inspections revealed extensive cracking in the concrete girders. Problems were traced to the inadequate quality of tendon grouting, resulting in the partially bonded condition. The TerraSAR-X radar satellite, operated by the German Aerospace Center, was used to acquire radar imagery in the Staring SpotLight mode from the ascending and descending orbits at 11-day intervals. The data were processed with the SqueeSAR algorithm, resulting in millimeter-range precision of the time-displacement series. No permanent deformations were detected at the posttensioned segments during the monitoring period of 1.3 years. The high density of the measurement points allowed adequate characterization of bridge displacements. The results of the interferometric analysis attest to the feasibility of implementing satellite-based performance monitoring of bridges, offering an innovative asset management tool that can complement and augment current inspection methods.
- 25 April 2019
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2673  (8) , 310-321
Evaluation of the Long-Term Performance of Woven Geotextile Used between Base Course and Subgrade of a Paved Road
The purpose of this research was to investigate the properties of the exhumed geotextile from a low-volume road on the Virginia Department of Transportation network. The exhumed geotextiles have been in service for 23 years, which provided an opportunity to evaluate the longevity of the materials as well as to make assessments of how it relates to the changes in material properties. During this investigation, subgrade and base course materials were also obtained from the same site and an experimental program was developed to evaluate the effectiveness of the exhumed geotextiles for separation, stabilization, and filtration for the base course thicknesses of 4, 6, and 8 in. The results from this study combined with the results from the previous studies conducted at the same site showed that when the geotextile is placed between the subgrade and base course, the thinner the pavement section, the more evident the effectiveness of the geotextile improvements. One important finding of this research was that the placement of a geotextile reduced the particle breakage caused by abrasion under the applied transient loads. This was observed as a stabilization effect of the geotextile inclusion. As a general conclusion, for low-volume roads with relatively thin pavement sections, properly selected geotextiles provide benefits for separating the subgrade and base course (minimizing pumping), filtering infiltrated or ground water, and stabilizing the road profile. These benefits become more apparent when the thickness of the base course is less than 8 in.
- 25 April 2019
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2673  (8) , 310-321
Evaluation of the Long-Term Performance of Woven Geotextile Used between Base Course and Subgrade of a Paved Road
The purpose of this research was to investigate the properties of the exhumed geotextile from a low-volume road on the Virginia Department of Transportation network. The exhumed geotextiles have been in service for 23 years, which provided an opportunity to evaluate the longevity of the materials as well as to make assessments of how it relates to the changes in material properties. During this investigation, subgrade and base course materials were also obtained from the same site and an experimental program was developed to evaluate the effectiveness of the exhumed geotextiles for separation, stabilization, and filtration for the base course thicknesses of 4, 6, and 8 in. The results from this study combined with the results from the previous studies conducted at the same site showed that when the geotextile is placed between the subgrade and base course, the thinner the pavement section, the more evident the effectiveness of the geotextile improvements. One important finding of this research was that the placement of a geotextile reduced the particle breakage caused by abrasion under the applied transient loads. This was observed as a stabilization effect of the geotextile inclusion. As a general conclusion, for low-volume roads with relatively thin pavement sections, properly selected geotextiles provide benefits for separating the subgrade and base course (minimizing pumping), filtering infiltrated or ground water, and stabilizing the road profile. These benefits become more apparent when the thickness of the base course is less than 8 in.
- 21 March 2019
- Published by American Society of Civil Engineers (ASCE)
- p. 245-258
Long-Term Field Performance of Geosynthetics in Pavement Subgrades in Virginia
Geosynthetics are used in the pavement base/subgrade interface for possible benefits of filtration, drainage, separation to prevent base contamination, and subgrade reinforcement. The Virginia Department of Transportation has constructed two experimental sections using geosynthetics in Bedford and Albemarle counties that have been in service for 23 and 10 years, respectively. Recently, the Virginia Transportation Research Council conducted a follow-up investigation of the long-term performance of these sections. These sections were assessed using falling weight deflectometry and pavement condition ratings (i.e., a distress survey). In the Bedford project, sections with either geotextile or geogrid have a better structural condition than a section without geosynthetics. In addition, no evidence of contamination of base aggregate with subgrade clay was observed except for one segment with no geosynthetics and 4 inches (100 mm) of base. After 10 years, very little distresses was observed in the Albemarle project on both the control and geotextile sections.
- 21 March 2019
- Published by American Society of Civil Engineers (ASCE)
- p. 245-258
Long-Term Field Performance of Geosynthetics in Pavement Subgrades in Virginia
Geosynthetics are used in the pavement base/subgrade interface for possible benefits of filtration, drainage, separation to prevent base contamination, and subgrade reinforcement. The Virginia Department of Transportation has constructed two experimental sections using geosynthetics in Bedford and Albemarle counties that have been in service for 23 and 10 years, respectively. Recently, the Virginia Transportation Research Council conducted a follow-up investigation of the long-term performance of these sections. These sections were assessed using falling weight deflectometry and pavement condition ratings (i.e., a distress survey). In the Bedford project, sections with either geotextile or geogrid have a better structural condition than a section without geosynthetics. In addition, no evidence of contamination of base aggregate with subgrade clay was observed except for one segment with no geosynthetics and 4 inches (100 mm) of base. After 10 years, very little distresses was observed in the Albemarle project on both the control and geotextile sections.
- 15 July 2018
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2672  (45) , 23-35
Integrating Remote Sensing Data in Decision Support Systems for Transportation Asset Management
The objective of the research summarized in this manuscript is two-fold: to develop and make available a set of novel analysis tools, fully integrated in ArcGIS, that leverages the rich information provided by satellite-based remote sensing data to detect and characterize geohazards of interest to the transportation community; and to provide a modern web-based decision support system (DSS) in which these novel analysis products can be seamlessly integrated with existing datasets. Specifically, interferometric synthetic aperture radar (InSAR) and its derivatives are employed in this work. Each tool is designed to target a specific asset of interest to the transportation community: sinkhole detection, bridge differential settlement detection, slope stability assessment, and pavement distress evaluation. Furthermore, to allow interested parties to test the introduction of remote sensing data into their decision-making process without requiring the full integration with existing workflows, a modern web-based DSS is introduced. Thanks to the large coverage and the high update frequencies offered by satellite-based remote sensing data, datasets augmented with these new products can offer a near real-time overview of the network status and lead to better support in decisions about resources allocation, existing infrastructure monitoring, new infrastructure planning, and post-construction assessment.
- 15 July 2018
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2672  (45) , 23-35
Integrating Remote Sensing Data in Decision Support Systems for Transportation Asset Management
The objective of the research summarized in this manuscript is two-fold: to develop and make available a set of novel analysis tools, fully integrated in ArcGIS, that leverages the rich information provided by satellite-based remote sensing data to detect and characterize geohazards of interest to the transportation community; and to provide a modern web-based decision support system (DSS) in which these novel analysis products can be seamlessly integrated with existing datasets. Specifically, interferometric synthetic aperture radar (InSAR) and its derivatives are employed in this work. Each tool is designed to target a specific asset of interest to the transportation community: sinkhole detection, bridge differential settlement detection, slope stability assessment, and pavement distress evaluation. Furthermore, to allow interested parties to test the introduction of remote sensing data into their decision-making process without requiring the full integration with existing workflows, a modern web-based DSS is introduced. Thanks to the large coverage and the high update frequencies offered by satellite-based remote sensing data, datasets augmented with these new products can offer a near real-time overview of the network status and lead to better support in decisions about resources allocation, existing infrastructure monitoring, new infrastructure planning, and post-construction assessment.
- Open Access
- 20 April 2018
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2672  (52) , 57-66
Optimizing the Gradation of Fine Processed Reclaimed Asphalt Pavement and Aggregate Blends for Unbound Base Courses
The purpose of this research was to investigate the effect of changes in grain size distribution to the permanent deformation of two different fine processed reclaimed asphalt pavement (RAP) blended with base course virgin aggregate (VA). Grain size distribution of the RAP-VA blends were created following two different approaches. The first approach was based on mixing RAP and VA to have one grain size distribution, regardless of how much RAP was added to VA (here referred to as the engineered mixture design). The second approach was based on mixing RAP and VA with as-is gradation from the plants to proportions determined by weight and not controlling the outcome of the specific grain size of the mixture. This approach resulted in various grain size distributions (here referred as the as-is mixture design). The engineered mixture design was useful to quantify the effect of adding RAP to the blends, but was not a realistic approach to create blends that may be achieved in the field. The as-is mixture design could not only be achieved in the field, as demonstrated in this study, but also resulted in better performance in terms of permanent deformation. This manuscript describes the comparison of these two approaches and a methodology to optimize the gradation and develop thresholds for RAP-VA blends that may result in similar or better performance than the 100% as-is VA that is used to construct base course in pavement systems.
- 20 April 2018
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2672  (52) , 57-66
Open AccessOptimizing the Gradation of Fine Processed Reclaimed Asphalt Pavement and Aggregate Blends for Unbound Base Courses
The purpose of this research was to investigate the effect of changes in grain size distribution to the permanent deformation of two different fine processed reclaimed asphalt pavement (RAP) blended with base course virgin aggregate (VA). Grain size distribution of the RAP-VA blends were created following two different approaches. The first approach was based on mixing RAP and VA to have one grain size distribution, regardless of how much RAP was added to VA (here referred to as the engineered mixture design). The second approach was based on mixing RAP and VA with as-is gradation from the plants to proportions determined by weight and not controlling the outcome of the specific grain size of the mixture. This approach resulted in various grain size distributions (here referred as the as-is mixture design). The engineered mixture design was useful to quantify the effect of adding RAP to the blends, but was not a realistic approach to create blends that may be achieved in the field. The as-is mixture design could not only be achieved in the field, as demonstrated in this study, but also resulted in better performance in terms of permanent deformation. This manuscript describes the comparison of these two approaches and a methodology to optimize the gradation and develop thresholds for RAP-VA blends that may result in similar or better performance than the 100% as-is VA that is used to construct base course in pavement systems.
- 1 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1558-1561
Network-scale pavement roughness mapping using spaceborne high-resolution X-band SAR data
This paper studies the applicability of radar remote sensing data, specifically, high-resolution Synthetic Aperture Radar (SAR) data acquired at X-band frequencies, to the network-wide mapping of pavement roughness of roads in the United States. Based on a comparison of high-resolution X-band images from the Cosmo-SkyMed satellites with road roughness data in the form of International Roughness Index (IRI) measurements, we found that X-band radar brightness generally increases when pavement roughness worsens. We developed a signal model that relates radar brightness to IRI, and successfully inverted this model to distinguish well maintained road segments from segments in need of repair. Over test sites in Augusta County, VA, we found that our classification scheme reached an overall accuracy of 92%. This study demonstrates the capacity of X-band SAR for pavement roughness mapping and suggests that an incorporation of X-band SAR data into DOT operations could provide benefits that may result in costs savings.
- 1 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1558-1561
Network-scale pavement roughness mapping using spaceborne high-resolution X-band SAR data
This paper studies the applicability of radar remote sensing data, specifically, high-resolution Synthetic Aperture Radar (SAR) data acquired at X-band frequencies, to the network-wide mapping of pavement roughness of roads in the United States. Based on a comparison of high-resolution X-band images from the Cosmo-SkyMed satellites with road roughness data in the form of International Roughness Index (IRI) measurements, we found that X-band radar brightness generally increases when pavement roughness worsens. We developed a signal model that relates radar brightness to IRI, and successfully inverted this model to distinguish well maintained road segments from segments in need of repair. Over test sites in Augusta County, VA, we found that our classification scheme reached an overall accuracy of 92%. This study demonstrates the capacity of X-band SAR for pavement roughness mapping and suggests that an incorporation of X-band SAR data into DOT operations could provide benefits that may result in costs savings.
- 25 June 2016
- Published by Wiley
- p. 185-198
Transportation Infrastructure Monitoring Using Satellite Remote Sensing
- 25 June 2016
- Published by Wiley
- p. 185-198
Transportation Infrastructure Monitoring Using Satellite Remote Sensing
- Open Access
- 1 January 2016
- Published by Elsevier in Transportation Research Procedia
- Vol. 14, 3943-3952
Jointless Bridge Design at the Virginia Department of Transportation
- 1 January 2016
- Published by Elsevier in Transportation Research Procedia
- Vol. 14, 3943-3952
Open AccessJointless Bridge Design at the Virginia Department of Transportation