CVCarlos I. Hoyos Velasco

Carlos I. Hoyos Velasco

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Carlos I. Hoyos Velasco has a total of 2 co-authors. Here are the top co-authors by number of shared publications:

  • Fredy Edimer Hoyos

    Departamento de Energía Eléctrica y Automática, Facultad de Minas, Universidad Nacional de Colombia, Sede Medellín, Carrera 80 No. 65-223, Robledo, Medellín 050034, Colombia

    3 shared publications
  • John Edwin Candelo Becerra

    Departamento de Energía Eléctrica y Automática, Facultad de Minas, Universidad Nacional de Colombia, Sede Medellín, Carrera 80 No. 65-223, Robledo, Medellín 050034, Colombia

    3 shared publications

Latest Publications

  • Open Access

    Nonlinear Dynamics and Performance Analysis of a Buck Converter with Hysteresis Control

    by Carlos I. Hoyos Velasco, Fredy Edimer Hoyos Velasco, John E. Candelo-Becerra

    This paper presents the mathematical modeling and experimental implementation of a Buck converter with hysteresis control. The system is described using a state-space model. Theoretical and simulation studies show that the zero hysteresis control leads to an equilibrium point with the implication of an infinite commutation frequency, while the use of a constant hysteresis band induces a limit cycle with a finite switching frequency. There exists a tradeoff between voltage output ripple and transistor switching frequency. An experimental prototype for the Buck power converter is built, and theoretical results are verified experimentally. In general terms, the Buck converter with the hysteresis control shows a robust control with respect to load variations, with undesired high switching frequency taking place for a very narrow hysteresis band, which is solved by tuning the hysteresis band properly.


  • Open Access

    Application of Zero Average Dynamics and Fixed Point Induction Control Techniques to Control the Speed of a DC Motor with a Buck Converter

    by Fredy E. Hoyos, John E. Candelo-Becerra, Carlos I. Hoyos Velasco

    Several technological applications require well-designed control systems to induce a desired speed in direct current (DC) motors. Some controllers present saturation in the duty cycle, which generates variable switching frequency and subharmonics. The zero average dynamics and fixed point induction control (ZAD-FPIC) techniques have been shown to reduce these problems; however, little research has been done for DC motors, considering fixed switching frequency, quantization effects, and delays. Therefore, this paper presents the speed control of a DC motor by using a buck converter controlled with the ZAD-FPIC techniques. A fourth-order, non-linear mathematical model is used to describe the system dynamics, which combines electrical and electromechanical physical models. The dynamic response and non-linear system dynamics are studied for different scenarios where the control parameters are changed. Results show that the speed of the motor is successfully controlled when using ZAD-FPIC, with a non-saturated duty cycle presenting fixed switching frequency. Simulation and experimental tests show that the controlled system presents a good performance for different quantization levels, which makes it robust to the resolution for the measurement and type of sensor.


  • Open Access

    Model-Based Quasi-Sliding Mode Control with Loss Estimation Applied to DC–DC Power Converters

    by Fredy E. Hoyos, John E. Candelo-Becerra, Carlos I. Hoyos Velasco

    This paper presents the experimental implementation of a buck converter with quasi-sliding mode control combined with a loss estimator function. An online loss estimator is developed to estimate, in real time, the parasitic resistances of the converter and variations of the resistance in the load. The estimated loss resistance and the resistance of the load are embedded, in real time, into the model equations of the controller using Zero Average Dynamics and Fixed Point Induction Control techniques (ZAD-FPIC) to improve the control robustness to resistive parameter variations. Details of the experimental setup are presented to show developed electrical and electronic circuits, and experimental techniques are described to ensure the successful digital implementation of closed-loop control of the buck power converter. The proper shielding of electrical wiring in power electronics allows improvement to the quality of the measures by removing noise induced by electromagnetic interference. A trigger signal is used to implement the Pulse-Width Modulation (PWM) with centered pulse and to synchronize the sampling of analogical signals from the buck converter. Such synchronization allows the use of a lower sampling frequency and ensures the measurements at the right instant in time. Experimental results are in good agreement with numerical simulations, showing the effectiveness of the control approach.