Sergey Nosachev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sergey Nosachev has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- A. R. Zenin
Don State Technical University
1 shared publication - Alexander Rybak
Don State Technical University
1 shared publication - I. K. Tsybrii
Don State Technical University
1 shared publication - Irina S. Stremilova1 shared publication
- Mikhail Victorovich Chuveyko
Don State Technical University, 344000 Rostov-on-Don, Russia
1 shared publication - Veronika Khristoforova1 shared publication
Latest Publications
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2507 (1)
Modeling of the influence of the time constant of the thermodynamic subsystem of the cutting system on the dynamics of metal cutting
An important factor in the processing of metals by cutting on metal-cutting machines is the quality factor of the surface obtained during processing, while this quality directly depends on the roughness index, which, in turn, is due to the vibrations of the tool during cutting. The vibration mode of cutting in a group of metal-cutting lathes is caused by self-excitation factors of the cutting system, one of which is the feedback implemented through the thermodynamic subsystem of the cutting system. It is the inverse thermodynamic connection formed during cutting that is the subject of research in this work. The aim of the work is to assess the influence of the thermodynamic subsystem of the cutting system on the dynamics of processing of the time constant. The paper studies the mutual influence of the power component of the metal turning process by cutting on metal-cutting machines and the temperature in the cutting zone. Research methods full-scale and numerical experiments in which the Matlab package of mathematical programs was used for data processing and analysis. Results and discussion. The results of field and numerical experiments are presented, such as graphs of the deformation coordinates of the tool, temperatures in the cutting zone, phase trajectories of the deformation coordinates, as well as a graph of the total cutting force. Conclusion: The synthesized mathematical model allows us to qualitatively assess the vibration load on the instrument, according to the measured value of the time constant of the thermodynamic subsystem.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2507 (1)
Modeling of the influence of the time constant of the thermodynamic subsystem of the cutting system on the dynamics of metal cutting
An important factor in the processing of metals by cutting on metal-cutting machines is the quality factor of the surface obtained during processing, while this quality directly depends on the roughness index, which, in turn, is due to the vibrations of the tool during cutting. The vibration mode of cutting in a group of metal-cutting lathes is caused by self-excitation factors of the cutting system, one of which is the feedback implemented through the thermodynamic subsystem of the cutting system. It is the inverse thermodynamic connection formed during cutting that is the subject of research in this work. The aim of the work is to assess the influence of the thermodynamic subsystem of the cutting system on the dynamics of processing of the time constant. The paper studies the mutual influence of the power component of the metal turning process by cutting on metal-cutting machines and the temperature in the cutting zone. Research methods full-scale and numerical experiments in which the Matlab package of mathematical programs was used for data processing and analysis. Results and discussion. The results of field and numerical experiments are presented, such as graphs of the deformation coordinates of the tool, temperatures in the cutting zone, phase trajectories of the deformation coordinates, as well as a graph of the total cutting force. Conclusion: The synthesized mathematical model allows us to qualitatively assess the vibration load on the instrument, according to the measured value of the time constant of the thermodynamic subsystem.
- 15 September 2020
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 22 (3) , 44-58
Relationship of Temperature and Cutting Force with Tool Wear and Vibration in Metal Turning
- 15 September 2020
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 22 (3) , 44-58
Relationship of Temperature and Cutting Force with Tool Wear and Vibration in Metal Turning
- Open Access
- 4 October 2019
- Published by FSFEI HE Don State Technical University in Advanced Engineering Research (Rostov-on-Don)
- Vol. 19 (3) , 242-249
Theoretical background of hydraulic drive control system analysis for testing piston hydraulic cylinders
Introduction. The durability and performance of hydraulic machines is determined through life tests. At that, various braking devices (mechanical, electric, hydraulic, etc.) are used for strength loading of the hydraulic motor, as a result of which a significant amount of energy is lost. This can be avoided if the method of rotational motion with energy recovery is used during life tests. This approach is applicable for hydraulic pumps, motors, and hydraulic cylinders.Materials and Methods. A test bench is presented, the design of which provides recreation of the conditions most appropriate for the field operation of hydraulic cylinders. In this case, energy recovery is possible. To solve the research problems, methods of mathematical modeling were used, the basic functional parameters of the proposed design were calculated. The determination of the pressure increment at various points in the hydraulic system is based on the theory of volumetric rigidity. When modeling the motion of the moving elements of the bench hydraulic system, the laws of rotor motion are used.Research Results. In the structure of the test bench, the cylinders in question are located in the pressure main between the hydraulic pump and the hydraulic motor. This enables to significantly reduce the bench itself and to save a significant amount of energy due to its recovery. A basic hydraulic diagram of the test bench for piston hydraulic cylinders is presented, in which the operation of the moving elements of the system is shown. A mathematical modeling of the hydraulic system of the bench is performed. A kinematic diagram of the mechanism for transmitting motion between test cylinders is shown.Discussion and Conclusions. The system of equations presented in the paper shows how the increment of pressure at the selected nodal points of the energy recovery system is determined (in particular, how the increment depends on time, reduced coefficient of volumetric rigidity, operating fluid consumption, and piston areas). The velocities of the hydraulic pistons are determined according to the kinematic scheme of the mechanical transmission of the bench. Thus it can be argued that, thanks to the solution presented in the paper, the life test results of hydraulic cylinders will adequately reflect their operation under rated duties.
- 4 October 2019
- Published by FSFEI HE Don State Technical University in Advanced Engineering Research (Rostov-on-Don)
- Vol. 19 (3) , 242-249
Open AccessTheoretical background of hydraulic drive control system analysis for testing piston hydraulic cylinders
Introduction. The durability and performance of hydraulic machines is determined through life tests. At that, various braking devices (mechanical, electric, hydraulic, etc.) are used for strength loading of the hydraulic motor, as a result of which a significant amount of energy is lost. This can be avoided if the method of rotational motion with energy recovery is used during life tests. This approach is applicable for hydraulic pumps, motors, and hydraulic cylinders.Materials and Methods. A test bench is presented, the design of which provides recreation of the conditions most appropriate for the field operation of hydraulic cylinders. In this case, energy recovery is possible. To solve the research problems, methods of mathematical modeling were used, the basic functional parameters of the proposed design were calculated. The determination of the pressure increment at various points in the hydraulic system is based on the theory of volumetric rigidity. When modeling the motion of the moving elements of the bench hydraulic system, the laws of rotor motion are used.Research Results. In the structure of the test bench, the cylinders in question are located in the pressure main between the hydraulic pump and the hydraulic motor. This enables to significantly reduce the bench itself and to save a significant amount of energy due to its recovery. A basic hydraulic diagram of the test bench for piston hydraulic cylinders is presented, in which the operation of the moving elements of the system is shown. A mathematical modeling of the hydraulic system of the bench is performed. A kinematic diagram of the mechanism for transmitting motion between test cylinders is shown.Discussion and Conclusions. The system of equations presented in the paper shows how the increment of pressure at the selected nodal points of the energy recovery system is determined (in particular, how the increment depends on time, reduced coefficient of volumetric rigidity, operating fluid consumption, and piston areas). The velocities of the hydraulic pistons are determined according to the kinematic scheme of the mechanical transmission of the bench. Thus it can be argued that, thanks to the solution presented in the paper, the life test results of hydraulic cylinders will adequately reflect their operation under rated duties.
- Open Access
- 30 September 2014
- Published by FSFEI HE Don State Technical University in Advanced Engineering Research (Rostov-on-Don)
- Vol. 14 (3) , 127-137
MATHEMATICAL SIMULATION OF ELASTIC SLIP IN ‘WHEEL — ROAD SURFACE’ CONTACT
The problem of elastic sliding in the ‘wheel — road surface’ contact is considered. A mathematical surface interaction model is developed. The model presented here suggests that the road surface deformation processes can be neglected. The wheel is modeled as a set of elastic rim sectors mounted on an elastic disc. The model dynamics is mainly influenced by the interaction force of the rim sectors with the wheel center, the intersectional interaction force, and the contact surface interaction force. The experimental studies using numerical simulation methods are conducted. It is discovered that there is a dependence of the stalling load value on the other wheel properties. The obtained results are of interest for solving problems on the wheel motion control to prevent the contact disruption. The used holistic approach allows identifying the emergence that influences the overall system trajectory.
- 30 September 2014
- Published by FSFEI HE Don State Technical University in Advanced Engineering Research (Rostov-on-Don)
- Vol. 14 (3) , 127-137
Open AccessMATHEMATICAL SIMULATION OF ELASTIC SLIP IN ‘WHEEL — ROAD SURFACE’ CONTACT
The problem of elastic sliding in the ‘wheel — road surface’ contact is considered. A mathematical surface interaction model is developed. The model presented here suggests that the road surface deformation processes can be neglected. The wheel is modeled as a set of elastic rim sectors mounted on an elastic disc. The model dynamics is mainly influenced by the interaction force of the rim sectors with the wheel center, the intersectional interaction force, and the contact surface interaction force. The experimental studies using numerical simulation methods are conducted. It is discovered that there is a dependence of the stalling load value on the other wheel properties. The obtained results are of interest for solving problems on the wheel motion control to prevent the contact disruption. The used holistic approach allows identifying the emergence that influences the overall system trajectory.