Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Nesrine Barbana has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Environmental and Economic Assessment of a Solar-Powered UF-RO Brackish-Groundwater Desalination System for Irrigation in the Jordan Valley

    by Mathhar Bdour, Mohammad Al-Addous, Nesrine Barbana, Norman Schweimanns, Duaa Allahseh

    Water scarcity and groundwater salinization constrain irrigated agriculture in the Jordan Valley. This study evaluates a small-scale photovoltaic-powered brackish-water reverse osmosis (RO) desalination system successively upgraded from single-stage to two-stage RO operation and enhanced with ultrafiltration (UF) pre-treatment. The novelty of the study lies in the integrated assessment of these successive system configurations using field-based operational data. A screening gate-to-gate life-cycle assessment (LCA) and levelized cost of water (LCOW) analysis were performed for a functional unit of 1 m3 of irrigation-quality permeate. Three successive configurations were compared: (i) the baseline single-stage RO system, (ii) a two-stage RO system in which the first-stage concentrate was re-pressurized and treated in a second RO stage, and (iii) a UF-assisted two-stage RO system operated at up to 80% recovery. The configurations were compared using project inventory data for feedwater quality, recovery rate, energy demand, chemical consumption, materials and capital costs. The estimated climate-change impact of the UF-assisted PV-RO configuration was 0.9–1.4 kg CO2-eq/m3. This impact is comparatively low for brackish-water RO and reflects the use of PV electricity, although direct comparison with the literature values is limited by differences in LCA boundaries and assumptions. Recovery increased from 35% for single-stage RO to 60% for two-stage RO and 80% for UF-assisted two-stage RO, reducing brine generation from 1.86 to 0.25 m3/m3 permeate. Economically, increasing RO membrane capacity reduced LCOW from 1.28 to 0.86 JD/m3, whereas the UF-RO configuration increased LCOW to 1.40 JD/m3 because of added capital cost. The results indicate that high recovery and solar power can improve environmental performance, but UF adoption should be justified by reliability, water-quality and membrane-lifetime benefits.

  • Top Cited Papers
    Open Access

    Innovations in Solar-Powered Desalination: A Comprehensive Review of Sustainable Solutions for Water Scarcity in the Middle East and North Africa (MENA) Region

    by Mohammad Al-Addous, Mathhar Bdour, Shatha Rabaiah, Ali Boubakri, Norman Schweimanns, Nesrine Barbana, Johannes Wellmann

    Water scarcity poses significant challenges in arid regions like the Middle East and North Africa (MENA) due to constant population growth, considering the effects of climate change and water management aspects. The desalination technologies face problems like high energy consumption, high investment costs, and significant environmental impacts by brine discharge. This paper researches the relationships among water scarcity, energy-intensive desalination, and the development of renewable energy in MENA, with a particular focus on the Gulf Cooperation Council (GCC) countries. It examines innovations in solar-powered desalination, considering both solar photovoltaic (PV) and solar thermal technologies, in combination with traditional thermal desalination methods such as multi-effect distillation (MED) and multi-stage flash (MSF). The environmental impacts associated with desalination by brine discharge are also discussed, analyzing innovative technological solutions and avoidance strategies. Utilizing bibliometrics, this report provides a comprehensive analysis of scientific literature for the assessment of the research landscape in order to recognize trends in desalination technologies in the MENA region, providing valuable insights into emerging technologies and research priorities. Despite challenges such as high initial investment costs, technical complexities, and limited funding for research and development, the convergence of water scarcity and renewable energy presents significant opportunities for integrated desalination systems in GCC countries. Summarizing, this paper emphasizes the importance of interdisciplinary approaches and international collaboration by addressing the complex challenges of water scarcity and energy sustainability in the MENA region. By leveraging renewable energy sources and advancing desalination technologies, the region can achieve water security while mitigating environmental impacts and promoting economic development.


  • Open Access

    Static Robust Design Optimization Using the Stochastic Frontier Method: A Case Study of Pulsed EPD Process on TiO2 Films

    by Mohamed Ali Rezgui, Ali Trabelsi, Nesrine Barbana, Adel Ben Youssef, Mohammad Al-Addous

    This paper aims to optimize a pulsed electrophoretic deposition (EPD) process for TiO2 films. This is accomplished by determining the optimal configuration of the coating parameters from a robust optimization perspective. The experimental study uses a composite central design (CCD) with four control factors, i.e., the initial concentration (x1 in g/L), the deposition time (x2 in s), the duty cycle (x3 in %), and the voltage (x4 in V). The process responses that should all be maximized are the photocatalytic efficiency of the thin film (De) and three critical charges, which characterize the adhesion failure, i.e., LC1: the load at which the first cracks occurred; LC2: the load at which the film starts to delaminate at the edge level of the scratch track; and LC3: the load when the damage of the film exceeds 50%. This paper compares the robust optimization design of the EPD process using two methods: the robust design of processes and products using the stochastic frontier (RDPP-SF) and the surface response and desirability function methods. The findings show that the RDPP-SF method is superior to the response surface–desirability method for the process responses De and LC2 because of non-natural sources of variation; however, both methods perform comparably well while analyzing the LC1 and LC3 responses, which are subjected to pure random variability. The parameters setting for the process robust optimization are met in run 25 (x1 = 14 g/L, x2 = 150 s, x3 = 50%, and x4 40 V).


  • Open Access

    Possibilities for Anaerobic Digestion of Slaughter Waste and Flotates for Biomethane Production

    by Maximilian Philipp, Helene Ackermann, Nesrine Barbana, Jonas Pluschke, Sven Uwe Geißen

    Anaerobic digestion for biomethane production is an important tool regarding sustainable energy production. The objective of this study was to investigate the effects of the substrate composition and operating parameters on biomethane production during anaerobic digestion, focusing on the use of flotates and slaughterhouse waste as substrates with a high organic content. A novelty here was the use of a moving bed biofilm reactor (MBBR) with circulation pump for the anaerobic treatment of flotates, slaughter waste (SW), and their mixture. Flotates and waste from slaughterhouses offer a substrate with a high organic content. In this work, it was shown that both substrates provide a high biochemical methane potential (BMP). The highest methane yield was achieved by mixing both substrates. In continuous operation, special challenges arose, due to the high nitrogen and fat content of the substrates. These could be overcome by mixing the substrates and using a circulation pump in the reactor for improved back-mixing. As a result, the highest average methane yield of 0.65 NLCH4·gTS eli−1 was achieved in mesophilic operation at an organic loading rate (OLR) of 4.2 gTS·L−1·d−1.


  • Open Access

    Analysis and Design Methodology of a Novel Integration Topology of Storageless Off-Grid PV Systems

    by Zakariya M. Dalala, Saba Z. AlAqbani, Dima R. Khirfan, Layth H. Alhamad, Mohammad Al-Addous, Nesrine Barbana

    In this manuscript, a novel topology is proposed to integrate on-grid and off-grid PV systems supplying the same load premises. The load side is investigated and analyzed, and critical and non-critical loads are separated in terms of power supply. Critical and seasonal loads usually place stress on the grid’s point of common coupling (PCC). In the proposed topology, they are supplied by a novel topology for an off-grid solar pump PV system that lacks energy storage integration. The lack of energy storage batteries requires a novel design and sizing scheme for the off-grid PV system, and a methodology is proposed in this manuscript. The on-grid PV system is conventionally designed and coupled with the storage-less off-grid PV system to maintain load supply. The proposed methodology minimizes the ratings of the PCC and hence relieves stress on congested grids with renewable energy penetration, especially in condensed urban areas. The proposed structure enables the operation of microgrids with high penetration levels of renewable energy resources and minimizes dependance on storage batteries for off-grid systems. A case study is presented and thoroughly analyzed with the proposed methodology. The outcomes of the design process are evaluated economically and were found to be feasible, as is detailed and supported with simulation results.


  • PHOTOCATALYTIC TiO2FILMS SYNTHESIZED BY REACTIVE CHEMICAL SPRAYING

    by Nesrine Barbana, Adel BEN Youssef

    Titanium tetrachloride was used to synthesize titanium dioxide emulsion by the hydrolysis process. The semiconductor was deposited on raw unglazed ceramic and silicon substrate by the reactive chemical spraying process. The experimental conditions were chosen to ensure film adhesion. Obtained films were calcined at different temperatures ranging from 600∘C to 680∘C and characterized by X-ray diffraction, atomic force microscopy, optical measurement, contact angle measurement, and scratch test. The photocatalytic test was carried out under UV irradiation using an azo dye. The silicon substrate allowed to show the film structure. The AFM observation indicated that film roughness increased from 12[ ]nm to 32[ ]nm. Roughness growth corresponds to a large active surface and enhanced photocatalyst activity. During the photocatalyst test under UV irradiation, the sample calcined at 660∘C shows the best result with a degradation efficiency of 140[ ]mg[ ][ ][ ][ ]. The same sample was characterized by hydrophilic behavior and adhesion strength.


  • Open Access

    Modelling, Analysis, and Optimization of the Effects of Pulsed Electrophoretic Deposition Parameters on TiO2 Films Properties Using Desirability Optimization Methodology

    by Nesrine Barbana, Adel Ben Youssef, Mohamed Ali Rezgui, Latifa Bousselmi, Mohammad Al-Addous

    Titanium dioxide thin films immobilized over treated stainless steel were prepared using the pulsed electrophoretic deposition technique. The effects of process parameters (deposition time, applied voltage, initial concentration, and duty cycle) on photocatalytic efficiency and adhesion properties were investigated. To optimize the multiple properties of the thin film, a response surface methodology was combined with a desirability optimization methodology. Additionally, a quadratic model was established based on response surface analysis. The precision of the models was defined based on the analysis of variance (ANOVA), R2, and the normal plot of residuals. Then, a desirability function was used to optimize the multiple responses of the TiO2 thin film. The optimum values of applied voltage, catalyst concentration, duty cycle, and deposition time were 4 V, 16.34 g/L, 90% DC, and 150 s, respectively. Under these conditions, the decolorization efficiency of tested dye solution reached 82.75%. The values of critical charges LC1, LC2, and LC3 were 5.9 N, 12.5 N, and 16.7 N, respectively.


  • Open Access

    Potential and Feasibility Study of Hybrid Wind–Hydroelectric Power System with Water-Pumping Storage: Jordan as a Case Study

    by Mohammad Al-Addous, Sahil Al Hmidan, Mustafa Jaradat, Emil Alasis, Nesrine Barbana

    Periodic daily fluctuating demand for energy and power is a perceptible phenomenon, resulting in some moments of low demand for power and energy related to the huge energy comes from renewable energy systems, and some moments of peak load demand. This phenomenon, when combined with the non-stationary operation of huge capacity of renewable energy systems, results in no stability of voltage and frequency. To assure continuous network stability and to avoid energy losses from renewable energy systems that are subject to such control system, a hybrid system with energy–power storage in the form of pumped-hydro storage is considered the most suitable technically. This paper presents the design, modeling, analysis, and feasibility study of a hybrid wind and water-pumping storage system. The system was designed and analyzed for King Talal Dam (KTD), which is in Northern Jordan. The importance of this study is that it is directed mainly to Jordan and the Middle East and North Africa (MENA) region in general. The Jordanian renewable energy market is a promising arena that encourages developers, investors, engineers, and companies to develop and install pure renewable energy systems and renewable energy hybrid projects for the generation of electricity. The analysis of wind data is carried out using the “windfarm” software with 5.16 m/s as average wind speed. It is followed by the design of the hybrid system, which is simulated for a daily operation of 2–3 h as peak load hours. Based on the technical outcomes, cost study and feasibility analyses are carried out with Jordanian market prices. The total estimated annual energy production is 26,663,933 kWh from 10 MW wind farm and 5.2 MW pumping storage system. The aforementioned studies showed that a similar hybrid system is not always fully commercially feasible. However, a pure pumped-storage system proved to be technically feasible and assisting the grid. The whole project analysis determines that such a system boosts the operational stability of the grid, increases the penetration of renewable energy systems and reduces the energy import. In addition, 15,100,000 tons of CO2-equivalent is estimated as annual emissions reduction in this study.


  • Open Access

    Wastewater Reclamation in Major Jordanian Industries: A Viable Component of a Circular Economy

    by Motasem N. Saidan, Mohammad Al-Addous, Radwan A. Al-Weshah, Ibrahim Obada, Malek Alkasrawi, Nesrine Barbana

    Water scarcity remains the major looming challenge that is facing Jordan. Wastewater reclamation is considered as an alternative source of fresh water in semi-arid areas with water shortage or increased consumption. In the present study, the current status of wastewater reclamation and reuse in Jordan was analyzed considering 30 wastewater treatment plants (WWTPs). The assessment was based on the WWWTPs’ treatment processes in Jordan, the flowrates scale, and the effluents’ average total dissolved solid (TDS) contents. Accordingly, 60% of the WWTPs in Jordan used activated sludge as a treatment technology; 30 WWTPs were small scale (4 m3/day); and a total of 17.932 million m3 treated wastewater had low TDS (3 groundwater abstraction by major industries in Jordanian governorates. The results showed that the reclaimed wastewater can fully offset the industrial demand of fresh water in Amman, Zarqa, and Aqaba governorates. Hence, the environmental assessment showed positive impacts of reclaimed wastewater reuse scenario in terms of water depletion (saving of 72.55 million m3 groundwater per year) and climate change (17.683 million kg CO2Eq reduction). The energy recovery assessment in the small- and medium-scale WWTPs (4 m3/day) revealed that generation of electricity by anaerobic sludge digestion equates potentially to an offset of 0.11–0.53 kWh/m3. Finally, several barriers and prospects were put forth to help the stakeholders when considering entering into an agreement to supply and/or reuse reclaimed water.


  • Open Access

    Potential Study of Solar Thermal Cooling in Sub-Mediterranean Climate

    by Mustafa Jaradat, Mohammad Al-Addous, Aiman Albatayneh, Zakariya Dalala, Nesrine Barbana

    Air conditioning is becoming increasingly important in the energy supply of buildings worldwide. There has been a dramatic increase in energy requirements for cooling buildings in the Middle East and North Africa (MENA) region. This is before taking the effects of climate change into account, which will also entail a sharp increase in cooling requirements. This paper presents the potential of using a solar thermal absorption cooling system in Sub-Mediterranean Climate. Four sites in Jordan are now equipped with water-lithium bromide (H2O-LiBr) absorption chillers with a total nominal capacity of 530 kW. The focus of the paper was on the pilot system at the German Jordanian University (GJU) campus with a cooling capacity of 160 kW. The system was designed and integrated in order to support two existing conventional compression chillers with a nominal cooling capacity of 700 kW. The system was economically evaluated based on the observed cooling capacity results with a Coefficient of Performance (COP) equals 0.32, and compared with the values observed for a COP of 0.79 which is claimed by the manufacturer. Several techniques were implemented to evaluate the overall economic viability in-depth such as present worth value, internal rate of return, payback period, and levelized cost of electricity. The aforementioned economic studies showed that the absorption cooling system is deemed not feasible for the observed COP of 0.32 over a lifespan of 25 years. The net present value was equal to −137,684 JD and a payback period of 44 years which exceeds the expected lifespan of the project. Even for an optimal operation of COP = 0.79, the discounted payback period was equal to 23 years and the Levelized Cost of Electricity (LCOE) was equal to 0.65 JD/kWh. The survey shows that there are several weaknesses for applying solar thermal cooling in developing countries such as the high cost of these systems and, more significantly, the lack of experience for such systems.