Mojtaba Vakili-Azghandi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mojtaba Vakili-Azghandi has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Arash Fattah-Alhosseini
Department of Materials Engineering, Faculty of Engineering, Bu-Ali Sina University, Hamedan, Iran
7 shared publications Mohsen K. Keshavarz
4 shared publications- Ali Davoodi
Department of Materials and Metallurgical Engineering, Ferdowsi University of Mashhad, Mashhad, Iran
3 shared publications Jerzy A. Szpunar
3 shared publications- Ali Shirazi
Department of Mechanical Engineering, Bu-Ali Sina University, Hamedan, Iran
2 shared publications - Mahmoud Pezeshki
Faculty of Mechanical Engineering, Leibniz University Hannover, Garbsen, Germany
2 shared publications
Latest Publications
- 14 April 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 137 (11-12) , 6169-6185
An in-depth evaluation on the influences of elevated temperature ECAP on mechanical properties and corrosion behavior of copper metal
- 14 April 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 137 (11-12) , 6169-6185
An in-depth evaluation on the influences of elevated temperature ECAP on mechanical properties and corrosion behavior of copper metal
- Open Access
- 25 March 2025
- Published by Springer Nature in Research Square
An in-depth evaluation on the influences of elevated temperature ECAP on mechanical properties and corrosion behavior of copper metal
The need for large amounts of force in the equal channel angular pressing (ECAP) process has always caused problems and limitations in conducting it. In the current study, elevated temperature ECAP process is proposed as an approach to reduce force and its effects on the microstructural and mechanical properties of copper metal has been investigated, comprehensively. The research results showed that due to the phenomenon of recrystallization and the creation of refined and equiaxed grains, the microstructure of copper and its resistance to corrosion was improved. Accordingly, the stress concentration created in the triple points was decreased and, consequently, the fracture toughness of the material increased. Based on the present findings, the crack growth becomes intergranular, so the crack growth path becomes longer. Moreover, only one component of the applied force causes the crack to grow, as a result, the resistance of the material increases. Therefore, for example, the fatigue crack growth range threshold of the material subjected to the ECAP process was 3.5 times larger than those of the base metal (BM). Also, it can increase ultimate strength up to 65.4%, hardness up to 89% and impact toughness up to 91.9%. In addition, it was found that if the ECAP process is performed at elevated temperatures, the maximum required force can be reduced by 45.6%.
- 25 March 2025
- Published by Springer Nature in Research Square
Open AccessAn in-depth evaluation on the influences of elevated temperature ECAP on mechanical properties and corrosion behavior of copper metal
The need for large amounts of force in the equal channel angular pressing (ECAP) process has always caused problems and limitations in conducting it. In the current study, elevated temperature ECAP process is proposed as an approach to reduce force and its effects on the microstructural and mechanical properties of copper metal has been investigated, comprehensively. The research results showed that due to the phenomenon of recrystallization and the creation of refined and equiaxed grains, the microstructure of copper and its resistance to corrosion was improved. Accordingly, the stress concentration created in the triple points was decreased and, consequently, the fracture toughness of the material increased. Based on the present findings, the crack growth becomes intergranular, so the crack growth path becomes longer. Moreover, only one component of the applied force causes the crack to grow, as a result, the resistance of the material increases. Therefore, for example, the fatigue crack growth range threshold of the material subjected to the ECAP process was 3.5 times larger than those of the base metal (BM). Also, it can increase ultimate strength up to 65.4%, hardness up to 89% and impact toughness up to 91.9%. In addition, it was found that if the ECAP process is performed at elevated temperatures, the maximum required force can be reduced by 45.6%.
- 18 July 2022
- Published by Springer Nature in JOM
- Vol. 74 (12) , 4621-4631
Microstructural Evolution and Bio-Corrosion Behavior of a CP-Ti Processed by Multi-Pass of Severe Plastic Deformation
- 18 July 2022
- Published by Springer Nature in JOM
- Vol. 74 (12) , 4621-4631
Microstructural Evolution and Bio-Corrosion Behavior of a CP-Ti Processed by Multi-Pass of Severe Plastic Deformation
- 24 September 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 118 (7-8) , 2205-2220
Microstructure, mechanical, and tribological properties of Al7075-T6/Ti3AlC2/Al2O3 surface hybrid nanocomposite produced by friction stir processing: A comparison of hybrid ratio
- 24 September 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 118 (7-8) , 2205-2220
Microstructure, mechanical, and tribological properties of Al7075-T6/Ti3AlC2/Al2O3 surface hybrid nanocomposite produced by friction stir processing: A comparison of hybrid ratio
- Open Access
- 11 March 2021
- Published by Springer Nature in Research Square
Surface Hybrid Nanocomposite Produced by Friction Stir Processing: Microstructural Evolution, Mechanical Properties and Tribological Behavior
This study investigates the effects of incorporating Ti3AlC2 MAX phase into Al7075-T6 alloy by friction stir processing as well as adding Al2O3 nanoparticles to obtain a surface hybrid nanocomposite. These composites were successfully prepared by friction stir processing with a rotational speed of 1000 rpm and a travel speed of 28 mm/min after 3 passes. Optical, atomic force and scanning electron microscopy as well as microhardness, tensile and wear tests utilized to characterize the fabricated surface hybrid nanocomposites. Results showed that the maximum tensile strength and hardness value were achieved for Al-100% Al2O3 composite due to more grain refinement and effective dispersion of nanoparticles. Due to its laminar structure, Ti3AlC2 MAX phase enhanced better tribological characterization whereas Al2O3 nanoparticles cause better mechanical properties. Scanning electron microscopy tests revealed that the wear mechanism changes from adhesive for Al7075 alloy to adhesive-abrasive for the nanocomposite specimens.
- 11 March 2021
- Published by Springer Nature in Research Square
Open AccessSurface Hybrid Nanocomposite Produced by Friction Stir Processing: Microstructural Evolution, Mechanical Properties and Tribological Behavior
This study investigates the effects of incorporating Ti3AlC2 MAX phase into Al7075-T6 alloy by friction stir processing as well as adding Al2O3 nanoparticles to obtain a surface hybrid nanocomposite. These composites were successfully prepared by friction stir processing with a rotational speed of 1000 rpm and a travel speed of 28 mm/min after 3 passes. Optical, atomic force and scanning electron microscopy as well as microhardness, tensile and wear tests utilized to characterize the fabricated surface hybrid nanocomposites. Results showed that the maximum tensile strength and hardness value were achieved for Al-100% Al2O3 composite due to more grain refinement and effective dispersion of nanoparticles. Due to its laminar structure, Ti3AlC2 MAX phase enhanced better tribological characterization whereas Al2O3 nanoparticles cause better mechanical properties. Scanning electron microscopy tests revealed that the wear mechanism changes from adhesive for Al7075 alloy to adhesive-abrasive for the nanocomposite specimens.
- 1 January 2019
- Published by Elsevier in Synthetic Metals
- Vol. 247, 183-190
Electrodeposition of polypyrrole/ metal oxide nanocomposites for corrosion protection of mild steel—A comparative study
- 1 January 2019
- Published by Elsevier in Synthetic Metals
- Vol. 247, 183-190
Electrodeposition of polypyrrole/ metal oxide nanocomposites for corrosion protection of mild steel—A comparative study
- 1 August 2018
- Published by Elsevier in Measurement
- Vol. 124, 252-259
Optimizing the electrolyte chemistry parameters of PEO coating on 6061 Al alloy by corrosion rate measurement: Response surface methodology
- 1 August 2018
- Published by Elsevier in Measurement
- Vol. 124, 252-259
Optimizing the electrolyte chemistry parameters of PEO coating on 6061 Al alloy by corrosion rate measurement: Response surface methodology