Makoto Mizukami
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Makoto Mizukami has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Kaori Watanabe
Innovation Center for Organic Electronics Yamagata University 1‐808‐48, Arcadia Yonezawa Yamagata 992‐0119 Japan
6 shared publicationsMiho Abiko
Innovation Center for Organic Electronics Yamagata University 1‐808‐48, Arcadia Yonezawa Yamagata 992‐0119 Japan
6 shared publications- Anubha Bilgaiyan
Innovation Center for Organic Electronics Yamagata University 1-808-48, Arcadia, Yonezawa Yamagata 992-0119 Japan
2 shared publications Ryoko Horie
Innovation Center for Organic Electronics Yamagata University 1‐808‐48, Arcadia Yonezawa Yamagata 992‐0119 Japan
2 shared publicationsSeung-Il Cho
Innovation Center for Organic Electronics, Yamagata University, Yonezawa, Japan
2 shared publications- Seung-Il Cho
Graduate School of Science and Engineering, Yamagata University
2 shared publications
Latest Publications
- Open Access
- 30 September 2025
- Published by Wiley in Advanced Science
- Vol. 13 (2) , e14091
Low‐Temperature, Sustainable Manufacturing of Printed OTFT Backplanes for Electrophoretic and OLED Displays
Printed electronics have garnered significant attention for developing lightweight, cost‐effective, and environmentally friendly systems, driving significant advancements in the realm of sustainable electronics. This study introduces a printed active‐matrix organic thin‐film transistor (OTFT) backplane, fabricated under ambient conditions using low‐temperature printing and solution‐based processes. All electrode layers—including gate, source/drain, and pixel electrodes—are patterned through reverse‐offset printing (ROP), achieving high‐resolution multilayer integration with minimum line widths of 10 µm. The resulting OTFTs demonstrate robust performance in ambient air, achieving a carrier mobility of 1.12 cm 2 Vs −1 and on/off ratios exceeding 10⁸. The printed backplane is integrated with an electrophoretic display panel, enabling stable black‐and‐white image rendering through pixel‐level addressing. The same printing technology is employed to fabricate and drive an organic light‐emitting diode (OLED) display, utilizing white OLEDs with laminated color filters. X‐ray photoelectron spectroscopy validates that residual polydimethylsiloxane (PDMS) contamination from the ROP process can be eliminated through IPA rinsing, ensuring clean electrode surfaces. The fabrication process is conducted at temperatures exceeding 160 °C without vacuum equipment, significantly reducing energy consumption and material waste. This environmentally sustainable approach can be employed to develop future flexible and disposable electronics. The versatility of printed backplanes demonstrated here highlights their potential to drive next‐generation, environmentally friendly display technologies.
- 30 September 2025
- Published by Wiley in Advanced Science
- Vol. 13 (2) , e14091
Open AccessLow‐Temperature, Sustainable Manufacturing of Printed OTFT Backplanes for Electrophoretic and OLED Displays
Printed electronics have garnered significant attention for developing lightweight, cost‐effective, and environmentally friendly systems, driving significant advancements in the realm of sustainable electronics. This study introduces a printed active‐matrix organic thin‐film transistor (OTFT) backplane, fabricated under ambient conditions using low‐temperature printing and solution‐based processes. All electrode layers—including gate, source/drain, and pixel electrodes—are patterned through reverse‐offset printing (ROP), achieving high‐resolution multilayer integration with minimum line widths of 10 µm. The resulting OTFTs demonstrate robust performance in ambient air, achieving a carrier mobility of 1.12 cm 2 Vs −1 and on/off ratios exceeding 10⁸. The printed backplane is integrated with an electrophoretic display panel, enabling stable black‐and‐white image rendering through pixel‐level addressing. The same printing technology is employed to fabricate and drive an organic light‐emitting diode (OLED) display, utilizing white OLEDs with laminated color filters. X‐ray photoelectron spectroscopy validates that residual polydimethylsiloxane (PDMS) contamination from the ROP process can be eliminated through IPA rinsing, ensuring clean electrode surfaces. The fabrication process is conducted at temperatures exceeding 160 °C without vacuum equipment, significantly reducing energy consumption and material waste. This environmentally sustainable approach can be employed to develop future flexible and disposable electronics. The versatility of printed backplanes demonstrated here highlights their potential to drive next‐generation, environmentally friendly display technologies.
- 1 September 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (9) , 090903
Fabrication of organic integrated circuits based on the iodine-containing organic semiconductor I-ATT using solution shearing and a liquid-repellent pattern
Solution-sheared organic semiconductor films were fabricated using hydrophobic banks to yield high crystallinities and patterning. Herein, the I-containing material 2-iodoanthra [2, 3-b] thieno [2, 3-d] thiophene (I-ATT) exhibited an enhancement-mode organic thin-film transistor performance, with a respective mobility, threshold potential, and on/off ratio of 0.6 cm2 V−1 s−1, –11 V, and 103. The electrode alignment displayed a minimal effect on the mobility. Furthermore, inverter and NAND circuits based on a pseudo-complementary metal-oxide-semiconductor configuration exhibited reliable switching. These results indicate the viability of using solution-sheared I-ATT films in functional circuits, highlighting their potential for large-scale integration into printed electronics.
- 1 September 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (9) , 090903
Fabrication of organic integrated circuits based on the iodine-containing organic semiconductor I-ATT using solution shearing and a liquid-repellent pattern
Solution-sheared organic semiconductor films were fabricated using hydrophobic banks to yield high crystallinities and patterning. Herein, the I-containing material 2-iodoanthra [2, 3-b] thieno [2, 3-d] thiophene (I-ATT) exhibited an enhancement-mode organic thin-film transistor performance, with a respective mobility, threshold potential, and on/off ratio of 0.6 cm2 V−1 s−1, –11 V, and 103. The electrode alignment displayed a minimal effect on the mobility. Furthermore, inverter and NAND circuits based on a pseudo-complementary metal-oxide-semiconductor configuration exhibited reliable switching. These results indicate the viability of using solution-sheared I-ATT films in functional circuits, highlighting their potential for large-scale integration into printed electronics.
- Open Access
- 3 June 2021
- Published by Springer Nature in Scientific Reports
- Vol. 11 (1) , 1-12
Flexible, high mobility short-channel organic thin film transistors and logic circuits based on 4H–21DNTT
The low mobility and large contact resistance in organic thin-film transistors (OTFTs) are the two major limiting factors in the development of high-performance organic logic circuits. Here, solution-processed high-performance OTFTs and circuits are reported with a polymeric gate dielectric and 6,6 bis (trans-4-butylcyclohexyl)-dinaphtho[2,1-b:2,1-f]thieno[3,2-b]thiophene (4H–21DNTT) for the organic semiconducting layer. By optimizing and controlling the fabrication conditions, a high saturation mobility of 8.8 cm2 V−1 s−1 was demonstrated as well as large on/off ratios (> 106) for relatively short channel lengths of 15 μm and an average carrier mobility of 10.5 cm2 V−1 s−1 for long channel length OTFTs (> 50 μm). The pseudo-CMOS inverter circuit with a channel length of 15 μm exhibited sharp switching characteristics with a high signal gain of 31.5 at a supply voltage of 20 V. In addition to the inverter circuit, NAND logic circuits were further investigated, which also exhibited remarkable logic characteristics, with a high gain, an operating frequency of 5 kHz, and a short propagation delay of 22.1 μs. The uniform and reproducible performance of 4H–21DNTT OTFTs show potential for large-area, low-cost real-world applications on industry-compatible bottom-contact substrates.
- 3 June 2021
- Published by Springer Nature in Scientific Reports
- Vol. 11 (1) , 1-12
Open AccessFlexible, high mobility short-channel organic thin film transistors and logic circuits based on 4H–21DNTT
The low mobility and large contact resistance in organic thin-film transistors (OTFTs) are the two major limiting factors in the development of high-performance organic logic circuits. Here, solution-processed high-performance OTFTs and circuits are reported with a polymeric gate dielectric and 6,6 bis (trans-4-butylcyclohexyl)-dinaphtho[2,1-b:2,1-f]thieno[3,2-b]thiophene (4H–21DNTT) for the organic semiconducting layer. By optimizing and controlling the fabrication conditions, a high saturation mobility of 8.8 cm2 V−1 s−1 was demonstrated as well as large on/off ratios (> 106) for relatively short channel lengths of 15 μm and an average carrier mobility of 10.5 cm2 V−1 s−1 for long channel length OTFTs (> 50 μm). The pseudo-CMOS inverter circuit with a channel length of 15 μm exhibited sharp switching characteristics with a high signal gain of 31.5 at a supply voltage of 20 V. In addition to the inverter circuit, NAND logic circuits were further investigated, which also exhibited remarkable logic characteristics, with a high gain, an operating frequency of 5 kHz, and a short propagation delay of 22.1 μs. The uniform and reproducible performance of 4H–21DNTT OTFTs show potential for large-area, low-cost real-world applications on industry-compatible bottom-contact substrates.
- Open Access
- 4 August 2020
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (8)
Solution Processed Organic Transistors on Polymeric Gate Dielectric with Mobility Exceeding 15 cm2 V−1 s−1
- 4 August 2020
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (8)
Open AccessSolution Processed Organic Transistors on Polymeric Gate Dielectric with Mobility Exceeding 15 cm2 V−1 s−1
- 25 May 2020
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (8) , 2000156
Solution Processed Organic Transistors on Polymeric Gate Dielectric with Mobility Exceeding 15 cm2 V−1 s−1
Herein, 6,6′ bis (trans‐4‐pentylcyclohexyl)‐dinaphtho[2,1‐b:2′,1′‐f ]thieno[3,2‐b]thiophene (5H‐21DNTT)—a solution‐processable derivative of DNTT—is characterized and studied for its potential as a crystalline solution‐processed organic semiconductor to achieve high mobility and stable organic thin‐film transistor (OTFT) operation. The performance of a bottom‐gate, bottom‐contact OTFT with a 5H‐21DNTT semiconductor is analyzed with different polymeric organic gate dielectrics via various solution‐processed techniques. In comparison to other polymeric gate dielectrics, Parylene C exhibited a superior performance for 5H‐21DNTT OTFT devices, and the OTFT devices show a remarkable average mobility of 10.9 cm2 V−1 s−1, as well as a maximum mobility exceeding 15 cm2 V−1 s−1, with a 100% reliability factor.
- 25 May 2020
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (8) , 2000156
Solution Processed Organic Transistors on Polymeric Gate Dielectric with Mobility Exceeding 15 cm2 V−1 s−1
Herein, 6,6′ bis (trans‐4‐pentylcyclohexyl)‐dinaphtho[2,1‐b:2′,1′‐f ]thieno[3,2‐b]thiophene (5H‐21DNTT)—a solution‐processable derivative of DNTT—is characterized and studied for its potential as a crystalline solution‐processed organic semiconductor to achieve high mobility and stable organic thin‐film transistor (OTFT) operation. The performance of a bottom‐gate, bottom‐contact OTFT with a 5H‐21DNTT semiconductor is analyzed with different polymeric organic gate dielectrics via various solution‐processed techniques. In comparison to other polymeric gate dielectrics, Parylene C exhibited a superior performance for 5H‐21DNTT OTFT devices, and the OTFT devices show a remarkable average mobility of 10.9 cm2 V−1 s−1, as well as a maximum mobility exceeding 15 cm2 V−1 s−1, with a 100% reliability factor.
- 22 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 39 (1) , 39-42
Flexible Organic Light-Emitting Diode Displays Driven by Inkjet-Printed High-Mobility Organic Thin-Film Transistors
A 3.2-inch flexible color display, with a resolution of 50 ppi and, composed of bottom-emission multiphoton organic light-emitting diodes (OLEDs) and inkjet-printed organic thin-film transistors (OTFTs) with a bottom-gate/bottom-contact structure on a color filter, was developed. The device could successfully display color videos while being bent, and achieved a maximum luminance of 125 cd/m 2 with white light emission. The gate dielectrics of the OTFTs used on the backplane were bilayers of cardo polymer and Parylene, and the material used for the organic semiconductors was dithieno[2,3-d;2',3'-d']benzo[1,2-b;4,5-b']dithiophene blended with polystyrene in tetralin solvent, which was coated using inkjet printing to sufficiently fill the banks composed of a fluorine-based polymer. OTFTs with a channel length of 5 μm were created using the above process, and the structure achieved a high mobility of 1.2 cm2 /(V · s), making it suitable for flexible color OLED displays. The mobility was about three times as high as that obtained using solution shearing methods.
- 22 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 39 (1) , 39-42
Flexible Organic Light-Emitting Diode Displays Driven by Inkjet-Printed High-Mobility Organic Thin-Film Transistors
A 3.2-inch flexible color display, with a resolution of 50 ppi and, composed of bottom-emission multiphoton organic light-emitting diodes (OLEDs) and inkjet-printed organic thin-film transistors (OTFTs) with a bottom-gate/bottom-contact structure on a color filter, was developed. The device could successfully display color videos while being bent, and achieved a maximum luminance of 125 cd/m 2 with white light emission. The gate dielectrics of the OTFTs used on the backplane were bilayers of cardo polymer and Parylene, and the material used for the organic semiconductors was dithieno[2,3-d;2',3'-d']benzo[1,2-b;4,5-b']dithiophene blended with polystyrene in tetralin solvent, which was coated using inkjet printing to sufficiently fill the banks composed of a fluorine-based polymer. OTFTs with a channel length of 5 μm were created using the above process, and the structure achieved a high mobility of 1.2 cm2 /(V · s), making it suitable for flexible color OLED displays. The mobility was about three times as high as that obtained using solution shearing methods.