Min-Guk Seo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Min-Guk Seo has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Byeongwon Park
Korea Research Institute of Ships and Ocean Engineering Daejon Korea
2 shared publications - Sungjun Jung
Deep Ocean Engineering Research Center, Korea Research Institute of Ships & Ocean Engineering (KRISO), Busan 46729, Republic of Korea
2 shared publications - Yeon-Gyu Kim
Korea Research Institute of Ships and Ocean Engineering, Daejeon 34103, Korea
2 shared publications Bo Woo Nam
1 shared publication- Bo Woo Nam
Associate Professor, Department of Naval Architecture and Ocean Engineering, Seoul National University, Seoul, Republic of Korea
1 shared publication - Bo Woo Nam
Department of Naval Architecture and Ocean Engineering, Seoul National University, 1 Gwanak-ro, Gwanak-gu, Seoul 08826, South Korea
1 shared publication
Latest Publications
- 28 August 2026
- Published by Elsevier in Ocean Engineering
- Vol. 366
ITTC benchmarking campaign on the added resistance of KVLCC2 in regular and irregular waves
- 28 August 2026
- Published by Elsevier in Ocean Engineering
- Vol. 366
ITTC benchmarking campaign on the added resistance of KVLCC2 in regular and irregular waves
- Open Access
- 16 July 2026
- Published by Elsevier in Ocean Engineering
- Vol. 364
High-fidelity CFD investigation on parametric roll resonance of the KCS hull under various wave headings
- 16 July 2026
- Published by Elsevier in Ocean Engineering
- Vol. 364
Open AccessHigh-fidelity CFD investigation on parametric roll resonance of the KCS hull under various wave headings
- Open Access
- 28 February 2026
- Published by The Korean Society of Ocean Engineers in Journal of Ocean Engineering and Technology
- Vol. 40 (1) , 59-76
A Study on Layout Optimization of Large-Scale Offshore Wind Farms
In this study, we performed layout optimization for a 1.2 GW offshore wind farm, constructing a quantitative and reproducible procedure for large-scale farm design. Long-term European Center for Medium-Range Weather Forecasts ERA5 reanalysis data were used for wind modeling and calculation of the frequency of wind occurrence. Two scenarios were analyzed: optimizing turbine orientations based on alignment scores and fixing the boundary for internal layout optimization aligned with the prevailing wind. The optimization was performed using continuous ant colony optimization, and integrating annual energy production (AEP) accounting for wake effects, and in-field cable costs (estimated via a minimum spanning tree). The first scenario yielded the highest AEP. Conversely, the boundary-fixed case also showed a comparatively high AEP while achieving a lower cable installation cost. In conclusion, the proposed framework successfully integrates the wind resource, wake effect, and cable cost into a generalized optimization objective for offshore wind farm layout and can be easily extendable to diverse sites and projects. Finally, it can be further refined by incorporating constraints on the maximum number of series-connected turbines, optimizing the substation location, and expanding the objective function to a full levelized cost of energy calculation that includes electrical losses and curtailment.
- 28 February 2026
- Published by The Korean Society of Ocean Engineers in Journal of Ocean Engineering and Technology
- Vol. 40 (1) , 59-76
Open AccessA Study on Layout Optimization of Large-Scale Offshore Wind Farms
In this study, we performed layout optimization for a 1.2 GW offshore wind farm, constructing a quantitative and reproducible procedure for large-scale farm design. Long-term European Center for Medium-Range Weather Forecasts ERA5 reanalysis data were used for wind modeling and calculation of the frequency of wind occurrence. Two scenarios were analyzed: optimizing turbine orientations based on alignment scores and fixing the boundary for internal layout optimization aligned with the prevailing wind. The optimization was performed using continuous ant colony optimization, and integrating annual energy production (AEP) accounting for wake effects, and in-field cable costs (estimated via a minimum spanning tree). The first scenario yielded the highest AEP. Conversely, the boundary-fixed case also showed a comparatively high AEP while achieving a lower cable installation cost. In conclusion, the proposed framework successfully integrates the wind resource, wake effect, and cable cost into a generalized optimization objective for offshore wind farm layout and can be easily extendable to diverse sites and projects. Finally, it can be further refined by incorporating constraints on the maximum number of series-connected turbines, optimizing the substation location, and expanding the objective function to a full levelized cost of energy calculation that includes electrical losses and curtailment.
- Open Access
- 22 September 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (10) , 1842
Investigation of Low-Frequency Pitch Motion Characteristics for KRISO Standard Offshore Structure (K-Semi) Moored with a Truncation Mooring System
In this study, a model test was carried out to evaluate the station-keeping performance of Korea Research Institute of the Ships and Ocean Engineering (KRISO) standard semi-submersible, K-Semi in the Deep Ocean Engineering Basin (DOEB). The test was performed using a 1/50 scaled model with 12 mooring lines. The water depth was set to 3.2 m using a moveable bottom structure and truncated mooring lines. The dynamic behavior of the K-Semi was examined using a free decay test and regular wave as well as irregular wave tests of 1800. Large surge, heave and pitch due to drift motion from second-order effect were observed. The reason for the excessive low-frequency pitch motion is attributed to the restoring force and moment related to the mooring system as excessive surge occurred. The numerical model of K-Semi with the truncated mooring system was tuned and calibrated using model test results such as free decay and regular wave tests. Through numerical analysis, the motion characteristics of the K-Semi were compared with irregular model test results. In the case of a semi-submersible using a mooring system, it is observed that excessive pitch motion due to vertical restoring force and moment may occur when large horizontal displacement occurs. The effect of low-frequency pitch motion related to surge motion is an important factor in upwell estimation as well as second-order motion in referred DNV-GL OTG13.
- 22 September 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (10) , 1842
Open AccessInvestigation of Low-Frequency Pitch Motion Characteristics for KRISO Standard Offshore Structure (K-Semi) Moored with a Truncation Mooring System
In this study, a model test was carried out to evaluate the station-keeping performance of Korea Research Institute of the Ships and Ocean Engineering (KRISO) standard semi-submersible, K-Semi in the Deep Ocean Engineering Basin (DOEB). The test was performed using a 1/50 scaled model with 12 mooring lines. The water depth was set to 3.2 m using a moveable bottom structure and truncated mooring lines. The dynamic behavior of the K-Semi was examined using a free decay test and regular wave as well as irregular wave tests of 1800. Large surge, heave and pitch due to drift motion from second-order effect were observed. The reason for the excessive low-frequency pitch motion is attributed to the restoring force and moment related to the mooring system as excessive surge occurred. The numerical model of K-Semi with the truncated mooring system was tuned and calibrated using model test results such as free decay and regular wave tests. Through numerical analysis, the motion characteristics of the K-Semi were compared with irregular model test results. In the case of a semi-submersible using a mooring system, it is observed that excessive pitch motion due to vertical restoring force and moment may occur when large horizontal displacement occurs. The effect of low-frequency pitch motion related to surge motion is an important factor in upwell estimation as well as second-order motion in referred DNV-GL OTG13.
- Open Access
- 28 February 2022
- Published by The Korean Society of Ocean Engineers in Journal of Ocean Engineering and Technology
- Vol. 36 (1) , 50-60
Study on Extension of the 6-DOF Measurement Area for a Model Ship by Developing Auto-tracking Technology for Towing Carriage in Deep Ocean Engineering Tank
The deep ocean engineering basin (DOEB) of the Korea Research Institute of Ship and Ocean Engineering (KRISO) is equipped with an extreme-environment reproduction facility that can analyze the motion characteristics of offshore structures and ships. In recent years, there have been requirements for a wide range of six-degree-of-freedom (6-DOF) motion measurements for performing maneuvering tests and free-running tests of target objects (offshore structures or ships). This study introduces the process of developing a wide-area motion measurement technology by incorporating the auto-tracking technology of the towing carriage system to overcome the existing 6-DOF motion measurement limitation. To realize a wide range of motion measurements, the automatic tracking control system of the towing carriage in the DOEB was designed as a speed control method. To verify the control performance, the characteristics of the towing carriage according to the variation in control gain were analyzed. Finally, a wide range of motions was tested using a model test object (a remotely operated vehicle (ROV)), and the wide-area motion measurement technology was implemented using an automatic tracking control system for a towing carriage.
- 28 February 2022
- Published by The Korean Society of Ocean Engineers in Journal of Ocean Engineering and Technology
- Vol. 36 (1) , 50-60
Open AccessStudy on Extension of the 6-DOF Measurement Area for a Model Ship by Developing Auto-tracking Technology for Towing Carriage in Deep Ocean Engineering Tank
The deep ocean engineering basin (DOEB) of the Korea Research Institute of Ship and Ocean Engineering (KRISO) is equipped with an extreme-environment reproduction facility that can analyze the motion characteristics of offshore structures and ships. In recent years, there have been requirements for a wide range of six-degree-of-freedom (6-DOF) motion measurements for performing maneuvering tests and free-running tests of target objects (offshore structures or ships). This study introduces the process of developing a wide-area motion measurement technology by incorporating the auto-tracking technology of the towing carriage system to overcome the existing 6-DOF motion measurement limitation. To realize a wide range of motion measurements, the automatic tracking control system of the towing carriage in the DOEB was designed as a speed control method. To verify the control performance, the characteristics of the towing carriage according to the variation in control gain were analyzed. Finally, a wide range of motions was tested using a model test object (a remotely operated vehicle (ROV)), and the wide-area motion measurement technology was implemented using an automatic tracking control system for a towing carriage.
- Open Access
- 20 March 2021
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 9 (3) , 344
Experimental Study on Development of Mooring Simulator for Multi Floating Cranes
In this study, the coupled motion of a mooring system and multifloating cranes were analyzed. For the motion analysis, the combined equations of motions of the mooring line and multifloating cranes were introduced. The multibody equations for floating cranes were derived from the equations of motion. The finite element method (FEM) was used to derive equations to solve the stretchable catenary problem of the mooring line. To verify the function of mooring simulator, calculation results were compared with commercial mooring software. To validate the analysis results, we conducted an experimental test for offshore operation using two floating crane models scaled to 1:40. Two floating crane models and a pile model were established for operation of uprighting flare towers. During the model test, the motion of the floating cranes and tensions of the mooring lines were measured. Through the model test, the accuracy of the mooring analysis program developed in this study was verified. Therefore, if this mooring analysis program is used, it will be possible to perform a mooring analysis simulation at the same time as a maritime work simulation.
- 20 March 2021
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 9 (3) , 344
Open AccessExperimental Study on Development of Mooring Simulator for Multi Floating Cranes
In this study, the coupled motion of a mooring system and multifloating cranes were analyzed. For the motion analysis, the combined equations of motions of the mooring line and multifloating cranes were introduced. The multibody equations for floating cranes were derived from the equations of motion. The finite element method (FEM) was used to derive equations to solve the stretchable catenary problem of the mooring line. To verify the function of mooring simulator, calculation results were compared with commercial mooring software. To validate the analysis results, we conducted an experimental test for offshore operation using two floating crane models scaled to 1:40. Two floating crane models and a pile model were established for operation of uprighting flare towers. During the model test, the motion of the floating cranes and tensions of the mooring lines were measured. Through the model test, the accuracy of the mooring analysis program developed in this study was verified. Therefore, if this mooring analysis program is used, it will be possible to perform a mooring analysis simulation at the same time as a maritime work simulation.
- 25 February 2021
- Published by The Korean Society for Marine Environment and Energy in Journal of the Korean Society for Marine Environment & Energy
- Vol. 24 (1) , 32-46
Study of Towing Characteristics of Damaged Ship
본 연구에서는 해양사고로 인해서 손상된 선박의 예인 특성에 대해서 살펴보고자 하며, 이를 위해서 선박의 동적 해석을 수행할 수 있는 KIMAPS (KRISO Integrated Multi-body And Positioning Simulation system)프로그램을 사용하여 예인 시뮬레이션을 수행하였다. 선박의 예인 특성을 살펴보기 위해서 예선, 부선 및 예인삭을 수치 모델링하였다. 부선의 운동은 MMG 모델 및 횡유동 모델(cross-flow model)을 적용하여 모사하였으며, 두 모델의 결과를 비교하였다. 두 모델은 예인 불안정상태에서 운동 진폭 및 진동주기에서 다소 차이는 있었지만 전반적인 경향은 동일하였으며, 예인 안정상태에서의 예인 특성 값 및 예인가능성에 대한 판단은 거의 동일하였다. 따라서 빠른 판단이 필요한 긴급구난 상황에서는 비교적 단순한 횡유동 모델을 실용적인 관점에서 사용할 수 있을 것으로 생각된다. 또한 손상선박의 상태를 모사하기 위해서 상용 CFD 해석 프로그램인 StarCCM+를 사용하여 횡경사가 있는 상태에서의 조류하중계수를 추정하였으며, 이를 횡유동 모델에 적용하여 손상선박의 자세(횡경사 유무)에 따른 예인 특성을 확인하였다. 횡경사가 존재함으로 인해서 비대칭 유체력이 발생하였으며, 부선의 불안정한 운동 진폭 및 최대 장력이 증가함을 확인하였다.
- 25 February 2021
- Published by The Korean Society for Marine Environment and Energy in Journal of the Korean Society for Marine Environment & Energy
- Vol. 24 (1) , 32-46
Study of Towing Characteristics of Damaged Ship
본 연구에서는 해양사고로 인해서 손상된 선박의 예인 특성에 대해서 살펴보고자 하며, 이를 위해서 선박의 동적 해석을 수행할 수 있는 KIMAPS (KRISO Integrated Multi-body And Positioning Simulation system)프로그램을 사용하여 예인 시뮬레이션을 수행하였다. 선박의 예인 특성을 살펴보기 위해서 예선, 부선 및 예인삭을 수치 모델링하였다. 부선의 운동은 MMG 모델 및 횡유동 모델(cross-flow model)을 적용하여 모사하였으며, 두 모델의 결과를 비교하였다. 두 모델은 예인 불안정상태에서 운동 진폭 및 진동주기에서 다소 차이는 있었지만 전반적인 경향은 동일하였으며, 예인 안정상태에서의 예인 특성 값 및 예인가능성에 대한 판단은 거의 동일하였다. 따라서 빠른 판단이 필요한 긴급구난 상황에서는 비교적 단순한 횡유동 모델을 실용적인 관점에서 사용할 수 있을 것으로 생각된다. 또한 손상선박의 상태를 모사하기 위해서 상용 CFD 해석 프로그램인 StarCCM+를 사용하여 횡경사가 있는 상태에서의 조류하중계수를 추정하였으며, 이를 횡유동 모델에 적용하여 손상선박의 자세(횡경사 유무)에 따른 예인 특성을 확인하였다. 횡경사가 존재함으로 인해서 비대칭 유체력이 발생하였으며, 부선의 불안정한 운동 진폭 및 최대 장력이 증가함을 확인하였다.
- Open Access
- 29 January 2021
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 9 (2) , 136
Experimental and Numerical Analysis of Wave Drift Force on KVLCC2 Moving in Oblique Waves
In this study, experimental and numerical methods were applied to estimate surge and sway wave drift forces and yaw drift moment acting on KVLCC2, advancing in oblique wave. An experiment was carried out in the ocean engineering basin of the Korea Research Institute of Ships and Ocean Engineering (KRISO). A series of regular wave tests under various heading conditions were conducted to investigate ship motion responses and wave drift forces. A Rankine panel method based on potential flow was adopted in the numerical analysis, and the direct pressure integration method that integrates second-order pressure on the hull surface was applied to compute wave drift force. Through this study, validation data of wave drift force acting on KVLCC2 was established, and the computation capability of the potential-based numerical method was systematically analyzed.
- 29 January 2021
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 9 (2) , 136
Open AccessExperimental and Numerical Analysis of Wave Drift Force on KVLCC2 Moving in Oblique Waves
In this study, experimental and numerical methods were applied to estimate surge and sway wave drift forces and yaw drift moment acting on KVLCC2, advancing in oblique wave. An experiment was carried out in the ocean engineering basin of the Korea Research Institute of Ships and Ocean Engineering (KRISO). A series of regular wave tests under various heading conditions were conducted to investigate ship motion responses and wave drift forces. A Rankine panel method based on potential flow was adopted in the numerical analysis, and the direct pressure integration method that integrates second-order pressure on the hull surface was applied to compute wave drift force. Through this study, validation data of wave drift force acting on KVLCC2 was established, and the computation capability of the potential-based numerical method was systematically analyzed.
- 16 November 2019
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 142 (2) , 1-31
Numerical Evaluation of Ship Turning Performance in Regular and Irregular Waves
In this study, ship's maneuvering performance in waves is evaluated using numerical computation. To this end, three degrees-of-freedom (3DOF) planar motions are considered, and modular-type maneuvering model (maneuvering modeling group model (MMG model)) is applied. As external force of the equation of motion, hull force, propulsion force, rudder force, and wave drift force are adopted. In order to calculate wave drift force, seakeeping program which is based on a higher-order Rankine panel method is used by considering wave frequency, wave heading, ship's forward speed, and ship's lateral speed. This wave drift force is pre-calculated, made into database, and used in time domain simulation. The developed simulation program is validated by comparing the computation results of a turning test in regular waves with experimental data. Using this program, turning performance in irregular waves is evaluated and sensitivities for time signal of wave elevation are investigated. Through this study, it is confirmed that the simplified method based on the MMG model including wave drift force can provide good agreement with experimental data in a practical point of view. It can be observed that the simulation results considering the lateral speed show better agreement with the experimental data than those without consideration. In the case of irregular wave condition, the turning performance can be affected by wave random phases. When the ship encounters the beam sea during the turning operation, the wave elevations at that time play an essential role in the change of ship speed and turning trajectory.
- 16 November 2019
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 142 (2) , 1-31
Numerical Evaluation of Ship Turning Performance in Regular and Irregular Waves
In this study, ship's maneuvering performance in waves is evaluated using numerical computation. To this end, three degrees-of-freedom (3DOF) planar motions are considered, and modular-type maneuvering model (maneuvering modeling group model (MMG model)) is applied. As external force of the equation of motion, hull force, propulsion force, rudder force, and wave drift force are adopted. In order to calculate wave drift force, seakeeping program which is based on a higher-order Rankine panel method is used by considering wave frequency, wave heading, ship's forward speed, and ship's lateral speed. This wave drift force is pre-calculated, made into database, and used in time domain simulation. The developed simulation program is validated by comparing the computation results of a turning test in regular waves with experimental data. Using this program, turning performance in irregular waves is evaluated and sensitivities for time signal of wave elevation are investigated. Through this study, it is confirmed that the simplified method based on the MMG model including wave drift force can provide good agreement with experimental data in a practical point of view. It can be observed that the simulation results considering the lateral speed show better agreement with the experimental data than those without consideration. In the case of irregular wave condition, the turning performance can be affected by wave random phases. When the ship encounters the beam sea during the turning operation, the wave elevations at that time play an essential role in the change of ship speed and turning trajectory.
- 6 September 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment
- Vol. 233 (1) , 186-208
Numerical simulation of Sewol ferry capsize
In this study, numerical simulations are conducted in order to analyze the capsizing of roll-on/roll-off passenger ship, Sewol, which occurred on 16 April 2014. Since little is known about the reason of ship capsize, numerical simulation aims to the finding of possible scenarios which can cause this tragic accident. To this end, 4-degree-of-freedom (surge, sway, yaw, and roll motions) maneuvering equations are solved. The hydrodynamic coefficients obtained from a similar ship are applied and the WISH-Maneuver program of Seoul National University is used to perform the numerical simulation. The present analysis utilizes the probabilistic approach, which considers various physical variables and involves the simulation of a large number of cases using different combinations of the variables. The total number of simulation cases is over 70 millions, and the simulation results that are close to the conditions of the actual accident situation are selected. Through this process, the effects of the simulation variables are investigated and the potential causes of the accident are identified. The results show the hydrostatic instability of the ship in the operational condition owing to cargo overload and insufficient ballast water, which raised the vertical center of gravity. The reduced stability combined with large starboard steering angle and cargo movement during large heel may have been the decisive reason of capsizing.
- 6 September 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment
- Vol. 233 (1) , 186-208
Numerical simulation of Sewol ferry capsize
In this study, numerical simulations are conducted in order to analyze the capsizing of roll-on/roll-off passenger ship, Sewol, which occurred on 16 April 2014. Since little is known about the reason of ship capsize, numerical simulation aims to the finding of possible scenarios which can cause this tragic accident. To this end, 4-degree-of-freedom (surge, sway, yaw, and roll motions) maneuvering equations are solved. The hydrodynamic coefficients obtained from a similar ship are applied and the WISH-Maneuver program of Seoul National University is used to perform the numerical simulation. The present analysis utilizes the probabilistic approach, which considers various physical variables and involves the simulation of a large number of cases using different combinations of the variables. The total number of simulation cases is over 70 millions, and the simulation results that are close to the conditions of the actual accident situation are selected. Through this process, the effects of the simulation variables are investigated and the potential causes of the accident are identified. The results show the hydrostatic instability of the ship in the operational condition owing to cargo overload and insufficient ballast water, which raised the vertical center of gravity. The reduced stability combined with large starboard steering angle and cargo movement during large heel may have been the decisive reason of capsizing.