Minghui Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Minghui Yang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Bo Deng
University of South China, China
7 shared publications Bo Deng
College of Civil Engineering, University of South China, Hengyang, People’s Republic of China
4 shared publicationsMing-Hua Zhao
Hunan University
3 shared publicationsDaxi Fu
School of Civil Engineering, Beijing Jiaotong University, Beijing, People’s Republic of China
2 shared publicationsHe Chen
2 shared publicationsKe Chen
2 shared publications
Latest Publications
- Open Access
- 4 August 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-25
A new approach for evaluating continuous and discontinuous pipeline deformation induced by soil tunnel excavation
The deformation of the overlying pipeline caused by the soil tunnel excavation cannot be ignored in the case of the small spacing between the pipeline and the tunnel. Based on the rigid bar method, the pipeline-soil interaction model was established, with the simply supported beam as the basic system, and the loads acting on the pipeline by the soil are considered to be linearly distributed. Calculation methods for continuous and discontinuous pipeline deformations were established. The results calculated by the proposed method agree well with the experimental data of centrifuge tests and field data. Parametric study on the effect of the volume loss (η = 1%, 2%,3 %), rotational stiffness (β0 = 4.47 × 106N⋅m/rad, 4.47 × 108N⋅m/rad, 4.47 × 1010N⋅m/rad), ratio of pipeline section length to inflection point of soil settlement curve (L/is = 0.5, 1.0, 1.5, 2.0) and soil elastic modulus (E = 10 MPa, 30 MPa, 50 MPa) on the deflection and joint rotation angle of the discontinuous pipeline were carried out. Results show that: (1) the maximum pipeline deflection and the maximum rotation angle of the joint increase as η increases and decrease as β0 increases; (2) in the "odd" case, the maximum pipeline deflection and the maximum rotation angle of the joint first increase and then decrease as L/is increases, reaching a peak at L/is = 1.5, while in the "even" case, the maximum pipeline deflection decreases as L/is increases and the maximum rotation angle of the joint first increases and then decreases as L/is increases; (3) in the "odd" case, the maximum pipeline deflection and the maximum angle of rotation of the joint decrease as E increases, while the opposite trend is observed in the "even" case. Additionally, the maximum pipeline deflection and the maximum rotation angle of the joint are always greater in the "odd" case than that in the "even" case.
- 4 August 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-25
Open AccessA new approach for evaluating continuous and discontinuous pipeline deformation induced by soil tunnel excavation
The deformation of the overlying pipeline caused by the soil tunnel excavation cannot be ignored in the case of the small spacing between the pipeline and the tunnel. Based on the rigid bar method, the pipeline-soil interaction model was established, with the simply supported beam as the basic system, and the loads acting on the pipeline by the soil are considered to be linearly distributed. Calculation methods for continuous and discontinuous pipeline deformations were established. The results calculated by the proposed method agree well with the experimental data of centrifuge tests and field data. Parametric study on the effect of the volume loss (η = 1%, 2%,3 %), rotational stiffness (β0 = 4.47 × 106N⋅m/rad, 4.47 × 108N⋅m/rad, 4.47 × 1010N⋅m/rad), ratio of pipeline section length to inflection point of soil settlement curve (L/is = 0.5, 1.0, 1.5, 2.0) and soil elastic modulus (E = 10 MPa, 30 MPa, 50 MPa) on the deflection and joint rotation angle of the discontinuous pipeline were carried out. Results show that: (1) the maximum pipeline deflection and the maximum rotation angle of the joint increase as η increases and decrease as β0 increases; (2) in the "odd" case, the maximum pipeline deflection and the maximum rotation angle of the joint first increase and then decrease as L/is increases, reaching a peak at L/is = 1.5, while in the "even" case, the maximum pipeline deflection decreases as L/is increases and the maximum rotation angle of the joint first increases and then decreases as L/is increases; (3) in the "odd" case, the maximum pipeline deflection and the maximum angle of rotation of the joint decrease as E increases, while the opposite trend is observed in the "even" case. Additionally, the maximum pipeline deflection and the maximum rotation angle of the joint are always greater in the "odd" case than that in the "even" case.
- Open Access
- 17 January 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-16
Analytical solution of overlying pipe deformation caused by tunnel excavation based on Pasternak foundation model
The existing tunnel construction causes stratum deformation, which in turn leads to additional deformation and internal force of the overlying pipeline, thus increasing the risk of pipeline accidents. Then, how to correctly calculate the deformation and internal force of pipeline is the key to pipeline safety evaluation. To this end, this study firstly used the Pasternak foundation beam model to simulate the interaction of pipeline and soil, and divided the pipeline into the void area (i.e., pipeline-soil detachment) and the coordination area (i.e., pipeline-soil is always deformed together) between pipeline and soil. The differential equation of pipeline deflection for the void area and the coordination area were established respectively, and the solutions of pipeline deflection, the internal force of pipeline and the width of pipeline-soil void area were presented. Subsequently, the accuracy of the proposed method was verified by comparing with the available model and field test data, and it is found that the calculation results are too conservative without considering the pipeline-soil voiding phenomenon. Finally, the detailed parametric analysis was conducted. The results show that the pipeline deflection decreases with the increase of the pipeline-tunnel spacing between pipeline and tunnel, the pipeline bending stiffness and the soil elastic modulus, but increases with the increase of the formation loss rate, and the width of pipeline-soil void area increases with the increase of the pipeline-tunnel spacing, the pipeline bending stiffness and the soil elastic modulus.
- 17 January 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-16
Open AccessAnalytical solution of overlying pipe deformation caused by tunnel excavation based on Pasternak foundation model
The existing tunnel construction causes stratum deformation, which in turn leads to additional deformation and internal force of the overlying pipeline, thus increasing the risk of pipeline accidents. Then, how to correctly calculate the deformation and internal force of pipeline is the key to pipeline safety evaluation. To this end, this study firstly used the Pasternak foundation beam model to simulate the interaction of pipeline and soil, and divided the pipeline into the void area (i.e., pipeline-soil detachment) and the coordination area (i.e., pipeline-soil is always deformed together) between pipeline and soil. The differential equation of pipeline deflection for the void area and the coordination area were established respectively, and the solutions of pipeline deflection, the internal force of pipeline and the width of pipeline-soil void area were presented. Subsequently, the accuracy of the proposed method was verified by comparing with the available model and field test data, and it is found that the calculation results are too conservative without considering the pipeline-soil voiding phenomenon. Finally, the detailed parametric analysis was conducted. The results show that the pipeline deflection decreases with the increase of the pipeline-tunnel spacing between pipeline and tunnel, the pipeline bending stiffness and the soil elastic modulus, but increases with the increase of the formation loss rate, and the width of pipeline-soil void area increases with the increase of the pipeline-tunnel spacing, the pipeline bending stiffness and the soil elastic modulus.
- Open Access
- 6 October 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (19) , 12699
Estimation of Active Earth Pressure for Narrow Unsaturated Backfills Considering Soil Arching Effect and Interlayer Shear Stress
Affected by climatic conditions such as rainfall, evaporation and air temperature, most of the backfill soil is in an unsaturated state, and the decrease in matric suction leads to the failure of the retaining structure. In view of this, this study takes the vertical rigid retaining wall with narrow unsaturated backfill as the research object, assuming that the backfill behind the wall forms a circular soil arch and considering the interlayer shear stress; thus, the analytical solution of the active earth pressure of narrow unsaturated soil is derived based on the thin layer element method. The reliability of this method is verified by comparing with the experimental and existing theoretical results. A parameter analysis demonstrates that with the increase in the interface friction angle of the moving wall–soil, the average shear stress coefficient of zone I and zone II increases gradually, but with the increase in the interface friction angle of the fixed wall–soil, the average shear stress coefficient of zone I decreases; with the increase in effective internal friction angle and effective cohesion, the active earth pressure decreases and the tension crack depth increases; with the increase in the interface friction angle, the active earth pressure in the upper part of the retaining wall increases slightly, while the active earth pressure in the lower part decreases obviously; with the increase in matric suction, the active earth pressure first decreases rapidly and then increases gradually, and the tension crack depth first increases and then decreases, but the distribution pattern of the horizontal active earth pressure remains unchanged; the active earth pressure decreases with the decrease in the aspect ratio, and when the aspect ratio is smaller, the attenuation is more obvious; until the aspect ratio reaches a certain value, the active earth pressure is basically unchanged.
- 6 October 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (19) , 12699
Open AccessEstimation of Active Earth Pressure for Narrow Unsaturated Backfills Considering Soil Arching Effect and Interlayer Shear Stress
Affected by climatic conditions such as rainfall, evaporation and air temperature, most of the backfill soil is in an unsaturated state, and the decrease in matric suction leads to the failure of the retaining structure. In view of this, this study takes the vertical rigid retaining wall with narrow unsaturated backfill as the research object, assuming that the backfill behind the wall forms a circular soil arch and considering the interlayer shear stress; thus, the analytical solution of the active earth pressure of narrow unsaturated soil is derived based on the thin layer element method. The reliability of this method is verified by comparing with the experimental and existing theoretical results. A parameter analysis demonstrates that with the increase in the interface friction angle of the moving wall–soil, the average shear stress coefficient of zone I and zone II increases gradually, but with the increase in the interface friction angle of the fixed wall–soil, the average shear stress coefficient of zone I decreases; with the increase in effective internal friction angle and effective cohesion, the active earth pressure decreases and the tension crack depth increases; with the increase in the interface friction angle, the active earth pressure in the upper part of the retaining wall increases slightly, while the active earth pressure in the lower part decreases obviously; with the increase in matric suction, the active earth pressure first decreases rapidly and then increases gradually, and the tension crack depth first increases and then decreases, but the distribution pattern of the horizontal active earth pressure remains unchanged; the active earth pressure decreases with the decrease in the aspect ratio, and when the aspect ratio is smaller, the attenuation is more obvious; until the aspect ratio reaches a certain value, the active earth pressure is basically unchanged.
- Open Access
DEM Analysis and Simplified Calculation of Passive Earth Pressure on Retaining Walls Backfilled with Sand Considering Strain-Softening Behavior
Common calculation methods of passive earth pressure, such as the Rankine or Coulomb earth pressure theory, assume that the width of the fill behind the wall is sufficient for the development of the slip surface and that after the passive earth pressure reaches the limit state, its value remains unchanged with the increase of displacement of the retaining wall. Nevertheless, cases with narrow backfill width should be considered when retaining walls must be built close to existing stabilization walls in urban areas or near rock faces in mountainous areas. Furthermore, for sand, especially dense sand, when the displacement of the retaining wall is large, a strain-softening behavior similar to the triaxial test will appear, resulting in a decrease in passive earth pressure. In this regard, a practical model for strain-softening of dense sand is proposed firstly and verified by the discrete element method (DEM) using the Particle Flow Code (PFC-2D) software. Then, based on the sliding surface shape obtained by DEM, a simplified method for determining the passive earth pressure distribution of retaining walls using limit equilibrium analysis was proposed. Finally, the passive earth pressures calculated by the proposed method agree well with those from PFC results, and the effects of the width of the backfill and displacement of retaining wall on the distribution of active earth pressure were discussed.
Open AccessDEM Analysis and Simplified Calculation of Passive Earth Pressure on Retaining Walls Backfilled with Sand Considering Strain-Softening Behavior
Common calculation methods of passive earth pressure, such as the Rankine or Coulomb earth pressure theory, assume that the width of the fill behind the wall is sufficient for the development of the slip surface and that after the passive earth pressure reaches the limit state, its value remains unchanged with the increase of displacement of the retaining wall. Nevertheless, cases with narrow backfill width should be considered when retaining walls must be built close to existing stabilization walls in urban areas or near rock faces in mountainous areas. Furthermore, for sand, especially dense sand, when the displacement of the retaining wall is large, a strain-softening behavior similar to the triaxial test will appear, resulting in a decrease in passive earth pressure. In this regard, a practical model for strain-softening of dense sand is proposed firstly and verified by the discrete element method (DEM) using the Particle Flow Code (PFC-2D) software. Then, based on the sliding surface shape obtained by DEM, a simplified method for determining the passive earth pressure distribution of retaining walls using limit equilibrium analysis was proposed. Finally, the passive earth pressures calculated by the proposed method agree well with those from PFC results, and the effects of the width of the backfill and displacement of retaining wall on the distribution of active earth pressure were discussed.
- Open Access
- 1 January 2022
- Published by Wiley in Advances in Civil Engineering
- Vol. 2022 (1)
Simplified Calculation Method for Overlying Pipeline Deformation Induced by Tunnel Construction in Soil Based on the Energy Principle
The deformation of the overlay pipeline caused by the excavation of the soil tunnel in the case of small spacing cannot be ignored. Based on the experience of previous engineering, this paper assumes that the settlement of the overlying pipeline caused by tunnel excavation satisfies the basic morphology of Gaussian distribution. On this basis, the soil displacement is converted into load acting on the pipeline, and the energy variation principle is introduced, and the energy variation equation of the pipe‐soil system is established, which is iteratively solved based on the principle of minimum potential energy, so as to obtain the calculation method of overlay pipeline vertical deformation caused by soil tunnel excavation, which is more simple and practical than the previous method. The calculation results were compared with the existing tests and engineering examples to verify the correctness of the proposed formula. Finally, the influence of pipeline material, formation loss rate, and intersection angle between the tunnel and pipeline on pipeline vertical deformation was analyzed. The comparative analysis shows that the pipeline deformation decreases with the increase of tunnel angle and pipeline elastic modulus, but increases with the increase of formation loss rate.
- 1 January 2022
- Published by Wiley in Advances in Civil Engineering
- Vol. 2022 (1)
Open AccessSimplified Calculation Method for Overlying Pipeline Deformation Induced by Tunnel Construction in Soil Based on the Energy Principle
The deformation of the overlay pipeline caused by the excavation of the soil tunnel in the case of small spacing cannot be ignored. Based on the experience of previous engineering, this paper assumes that the settlement of the overlying pipeline caused by tunnel excavation satisfies the basic morphology of Gaussian distribution. On this basis, the soil displacement is converted into load acting on the pipeline, and the energy variation principle is introduced, and the energy variation equation of the pipe‐soil system is established, which is iteratively solved based on the principle of minimum potential energy, so as to obtain the calculation method of overlay pipeline vertical deformation caused by soil tunnel excavation, which is more simple and practical than the previous method. The calculation results were compared with the existing tests and engineering examples to verify the correctness of the proposed formula. Finally, the influence of pipeline material, formation loss rate, and intersection angle between the tunnel and pipeline on pipeline vertical deformation was analyzed. The comparative analysis shows that the pipeline deformation decreases with the increase of tunnel angle and pipeline elastic modulus, but increases with the increase of formation loss rate.
- 11 May 2021
- Published by Springer Nature in Acta Geotechnica
- Vol. 17 (1) , 205-220
Stability analysis of geosynthetic-reinforced soil structures under steady infiltrations
- 11 May 2021
- Published by Springer Nature in Acta Geotechnica
- Vol. 17 (1) , 205-220
Stability analysis of geosynthetic-reinforced soil structures under steady infiltrations
- 18 September 2020
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 80 (2) , 835-850
Bearing capacity analysis of submerged slopes subjected to water drawdown based on a nonassociated flow rule and nonlinear failure criteria
- 18 September 2020
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 80 (2) , 835-850
Bearing capacity analysis of submerged slopes subjected to water drawdown based on a nonassociated flow rule and nonlinear failure criteria
- 1 August 2020
- Published by American Society of Civil Engineers (ASCE) in International Journal of Geomechanics
- Vol. 20 (8) , 04020115
Slip Surface and Active Earth Pressure of Cohesionless Narrow Backfill behind Rigid Retaining Walls under Translation Movement Mode
A slip-failure surface forms in the backfill soil upon sufficient yielding or movement of the wall that retains the backfill soil. The shape of the slip-failure surface plays an important role in estimating the lateral earth pressure, including its magnitude and location of its resultant force. As retaining walls at times must be built with narrow and constrained backfill space, this study presents an analytic derivation of the slip-surface shape in narrow cohesionless soil behind a rigid retaining wall under translation movement mode of the wall. Results of a series of experimental tests were presented to demonstrate the effects of narrow backfill spaces on forming the slip surface and that the slip surfaces are curvilinear planes developed from the heel of the retaining wall to the crest of the backfill. Based on the experimental findings, a rigorous analytic derivation using a variational limit equilibrium method is conducted to determine the governing equation for the shape of the slip surface in the narrow backfill soil. The analysis reveals that the active failure plane of the narrow soil behind a rigid retaining wall agrees well with a logarithmic spiral plane. The derived log-spiral slip-surface plane is further verified by experimentally observed slip surface and measured active lateral earth pressure. Substantial discrepancy was observed in the lateral earth pressure distribution between the logarithmic spiral slip surface and the assumed linear planar slip surface, indicating that the assumption of a linear planar slip surface in narrow backfill may result in significantly erroneous estimation and lead to an overly conservative and uneconomical design. Furthermore, a threshold value of 0.5 is identified for the backfill width/height ratio that distinguishes the narrow backfill from a sufficiently wide backfill.
- 1 August 2020
- Published by American Society of Civil Engineers (ASCE) in International Journal of Geomechanics
- Vol. 20 (8) , 04020115
Slip Surface and Active Earth Pressure of Cohesionless Narrow Backfill behind Rigid Retaining Walls under Translation Movement Mode
A slip-failure surface forms in the backfill soil upon sufficient yielding or movement of the wall that retains the backfill soil. The shape of the slip-failure surface plays an important role in estimating the lateral earth pressure, including its magnitude and location of its resultant force. As retaining walls at times must be built with narrow and constrained backfill space, this study presents an analytic derivation of the slip-surface shape in narrow cohesionless soil behind a rigid retaining wall under translation movement mode of the wall. Results of a series of experimental tests were presented to demonstrate the effects of narrow backfill spaces on forming the slip surface and that the slip surfaces are curvilinear planes developed from the heel of the retaining wall to the crest of the backfill. Based on the experimental findings, a rigorous analytic derivation using a variational limit equilibrium method is conducted to determine the governing equation for the shape of the slip surface in the narrow backfill soil. The analysis reveals that the active failure plane of the narrow soil behind a rigid retaining wall agrees well with a logarithmic spiral plane. The derived log-spiral slip-surface plane is further verified by experimentally observed slip surface and measured active lateral earth pressure. Substantial discrepancy was observed in the lateral earth pressure distribution between the logarithmic spiral slip surface and the assumed linear planar slip surface, indicating that the assumption of a linear planar slip surface in narrow backfill may result in significantly erroneous estimation and lead to an overly conservative and uneconomical design. Furthermore, a threshold value of 0.5 is identified for the backfill width/height ratio that distinguishes the narrow backfill from a sufficiently wide backfill.
- 1 May 2020
- Published by Elsevier in Computers and Geotechnics
- Vol. 121
A new hysteresis model of the water retention curve based on pore expansion and contraction
- 1 May 2020
- Published by Elsevier in Computers and Geotechnics
- Vol. 121
A new hysteresis model of the water retention curve based on pore expansion and contraction
- Open Access
Relative Permeability of Porous Media with Nonuniform Pores
Most classical predictive models of relative permeability conceptualize the pores in porous media as assemblies of uniform capillary tubes with different sizes. However, this simplification may overestimate the transport capacity of porous media due to overlooking the effects of the pore nonuniformity. This study presents a simple way to quantify the effect of the nonuniformity of pore cross section on the transport characteristic of unsaturated porous media. The way is based on the index relationship between the porosity of a newly defined reference cross section and that of porous media, which satisfies the intrinsic constraints for the nonuniform porosity of cross sections in porous media. Moreover, the index factor can be captured by a newly defined parameter, called the nonuniformity factor, which is used to establish an extended Darcy’s law. Based on these, a fractal-based continuous analytical model and a fractal-based Monte Carlo model of relative permeability as well as a permeability-porosity model are established. Experimental data of five wetting-nonwetting phase systems, including the water-air, water-steam, water-nitrogen, water-oil, and oil-gas systems, are selected to assess the performance of the proposed model. The results confirm the proposed model’s capacity in capturing the transport properties of various porous media. It is found that the nonuniformity of pores can significantly increase the resistance of fluid flow and thus reduce the transport capacity of porous media.
Open AccessRelative Permeability of Porous Media with Nonuniform Pores
Most classical predictive models of relative permeability conceptualize the pores in porous media as assemblies of uniform capillary tubes with different sizes. However, this simplification may overestimate the transport capacity of porous media due to overlooking the effects of the pore nonuniformity. This study presents a simple way to quantify the effect of the nonuniformity of pore cross section on the transport characteristic of unsaturated porous media. The way is based on the index relationship between the porosity of a newly defined reference cross section and that of porous media, which satisfies the intrinsic constraints for the nonuniform porosity of cross sections in porous media. Moreover, the index factor can be captured by a newly defined parameter, called the nonuniformity factor, which is used to establish an extended Darcy’s law. Based on these, a fractal-based continuous analytical model and a fractal-based Monte Carlo model of relative permeability as well as a permeability-porosity model are established. Experimental data of five wetting-nonwetting phase systems, including the water-air, water-steam, water-nitrogen, water-oil, and oil-gas systems, are selected to assess the performance of the proposed model. The results confirm the proposed model’s capacity in capturing the transport properties of various porous media. It is found that the nonuniformity of pores can significantly increase the resistance of fluid flow and thus reduce the transport capacity of porous media.