Andrija Stupar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Andrija Stupar has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Aleksandar Prodic
Laboratory for Integrated SMPS
4 shared publicationsJ. W. Kolar
Power Electronic Systems Laboratory, ETH Zurich, Zurich, Switzerland
3 shared publicationsJohann W. Kolar
Power Electronic Systems Laboratory, D-ITET, Swiss Federal Institute of Technology Zürich, Zürich, Switzerland
3 shared publicationsJosh A. Taylor
Institute for Sustainable Energy, University of Toronto, 10 King's College Road, Toronto, Canada
2 shared publications- Tim McRae
Laboratory for Power Management and Integrated SMPS, ECE Department, University of Toronto, CANADA
2 shared publications Uwe Drofenik
Power Electronic Systems Laboratory, D-ITET, Swiss Federal Institute of Technology Zürich, Zürich, Switzerland
2 shared publications
Latest Publications
- 2 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 34 (12) , 11912-11939
Multi-Objective Optimization of Multi-Level DC–DC Converters Using Geometric Programming
Multi-objective optimization of power converters is a time-consuming task, especially when multiple operating points and multiple converter topologies must be considered. As a result, various steps are often taken to simplify the design problem and restrict the size of the design space prior to going through an optimization procedure. While this saves time, it produces potentially sub-optimal designs, and existing approaches must trade-off between running time and design optimality. This paper presents an optimization-oriented method for modeling power converters and their components as posynomial functions, allowing multi-objective optimization of converters to be formulated as a geometric program, a type of convex optimization problem. This allows the use of fast, powerful solvers that guarantee global optimality of solutions. The method is demonstrated using the example of low-power multi-level flying capacitor step-down converters. Results show that, using geometric programming, sets of globally Pareto-optimal designs of 2-, 3-, and 4-level converters with respect to efficiency and power density, for one design space and one operating point, can be generated in as little as 25 seconds, on an mid- to upper-range laptop computer. Thus optimal designs for three different converter topologies for hundreds of different operating points and/or design spaces can be generated in several hours - less than the time required to globally optimize one converter topology at one operating point for one design space using currently prevalent methods. The paper also demonstrates how geometric programming can be used to quickly perform sensitivity and trade-off analysis of optimal converter designs.
- 2 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 34 (12) , 11912-11939
Multi-Objective Optimization of Multi-Level DC–DC Converters Using Geometric Programming
Multi-objective optimization of power converters is a time-consuming task, especially when multiple operating points and multiple converter topologies must be considered. As a result, various steps are often taken to simplify the design problem and restrict the size of the design space prior to going through an optimization procedure. While this saves time, it produces potentially sub-optimal designs, and existing approaches must trade-off between running time and design optimality. This paper presents an optimization-oriented method for modeling power converters and their components as posynomial functions, allowing multi-objective optimization of converters to be formulated as a geometric program, a type of convex optimization problem. This allows the use of fast, powerful solvers that guarantee global optimality of solutions. The method is demonstrated using the example of low-power multi-level flying capacitor step-down converters. Results show that, using geometric programming, sets of globally Pareto-optimal designs of 2-, 3-, and 4-level converters with respect to efficiency and power density, for one design space and one operating point, can be generated in as little as 25 seconds, on an mid- to upper-range laptop computer. Thus optimal designs for three different converter topologies for hundreds of different operating points and/or design spaces can be generated in several hours - less than the time required to globally optimize one converter topology at one operating point for one design space using currently prevalent methods. The paper also demonstrates how geometric programming can be used to quickly perform sensitivity and trade-off analysis of optimal converter designs.
- 27 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
Multi-objective optimization and comparison of multi-level DC-DC converters using convex optimization methods
Multi-level flying-capacitor converters are a promising topology for low-power applications. Conventional buck, 3- and 4-level converters have been modeled as a geometric program and optimized for loss and volume. Results show that 3- and 4-level converters are both smaller and more efficient over a wide range of design parameters.
- 27 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
Multi-objective optimization and comparison of multi-level DC-DC converters using convex optimization methods
Multi-level flying-capacitor converters are a promising topology for low-power applications. Conventional buck, 3- and 4-level converters have been modeled as a geometric program and optimized for loss and volume. Results show that 3- and 4-level converters are both smaller and more efficient over a wide range of design parameters.
- 1 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Posynomial models of inductors for optimization of power electronic systems by geometric programming
When optimizing power electronic converters for multiple objectives, such as power density and efficiency, the optimization of the magnetic components is often the most challenging and time-consuming task. In order to perform optimization quickly and efficiently, it would be advantageous to formulate converter optimization as a geometric program, a proven convex optimization method. In order to optimize for losses and volume via a geometric program however, all loss and volume models of the various components must be in the form of posynomials. While some loss models, such as those of semiconductors, are naturally in posynomial form or easily transformed, this is not the case for inductors. This paper presents a derivation of posynomial loss, volume, temperature, and saturation models for families of inductive components, based both on simulation and on adapting familiar analytical models into approximate posynomial form. The terms of the derived posynomial models are the inductor design variables, such as the number of turns, the air gap, and so forth. This allows inductors to be optimized for multiple design objectives as a geometric program.
- 1 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Posynomial models of inductors for optimization of power electronic systems by geometric programming
When optimizing power electronic converters for multiple objectives, such as power density and efficiency, the optimization of the magnetic components is often the most challenging and time-consuming task. In order to perform optimization quickly and efficiently, it would be advantageous to formulate converter optimization as a geometric program, a proven convex optimization method. In order to optimize for losses and volume via a geometric program however, all loss and volume models of the various components must be in the form of posynomials. While some loss models, such as those of semiconductors, are naturally in posynomial form or easily transformed, this is not the case for inductors. This paper presents a derivation of posynomial loss, volume, temperature, and saturation models for families of inductive components, based both on simulation and on adapting familiar analytical models into approximate posynomial form. The terms of the derived posynomial models are the inductor design variables, such as the number of turns, the air gap, and so forth. This allows inductors to be optimized for multiple design objectives as a geometric program.
- 15 November 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 2 (1) , 102-115
Optimization of Phase Change Material Heat Sinks for Low Duty Cycle High Peak Load Power Supplies
A power electronic device's lifetime depends on its maximum operating temperature and the temperature swings it is subjected to. Heat sinks employing phase change materials (PCMs) can be employed to achieve a temperature reduction, but only for a limited duration. This makes such heat sinks appropriate for use in applications with high peak loads but with low duty cycles. The heat sink is modeled using the thermal resistors and capacitors (RCs) network approach, and an optimization procedure for designing a hybrid air-cooled heat sink containing PCM is developed, yielding a maximum possible temperature reduction for a given application. It is shown that air-cooled heat sinks employing pure PCMs are best suited for applications with pulses width lengths of several minutes with a period of several tens of minutes. In order to achieve a faster response of the PCM, the concept of PCM-metal foam is explored and modeled. Experimental data is presented which confirms the validity of the thermal RC network approach.
- 15 November 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 2 (1) , 102-115
Optimization of Phase Change Material Heat Sinks for Low Duty Cycle High Peak Load Power Supplies
A power electronic device's lifetime depends on its maximum operating temperature and the temperature swings it is subjected to. Heat sinks employing phase change materials (PCMs) can be employed to achieve a temperature reduction, but only for a limited duration. This makes such heat sinks appropriate for use in applications with high peak loads but with low duty cycles. The heat sink is modeled using the thermal resistors and capacitors (RCs) network approach, and an optimization procedure for designing a hybrid air-cooled heat sink containing PCM is developed, yielding a maximum possible temperature reduction for a given application. It is shown that air-cooled heat sinks employing pure PCMs are best suited for applications with pulses width lengths of several minutes with a period of several tens of minutes. In order to achieve a faster response of the PCM, the concept of PCM-metal foam is explored and modeled. Experimental data is presented which confirms the validity of the thermal RC network approach.
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 27 (4) , 1732-1744
Towards a 99% Efficient Three-Phase Buck-Type PFC Rectifier for 400-V DC Distribution Systems
In telecom applications, the vision for a total power conversion efficiency from the mains to the output of point-of-load (PoL) converters of 95% demands optimization of every conversion step, i.e., the power factor correction (PFC) rectifier front-end should show an outstanding efficiency in the range of 99%. For recently discussed 400-V dc distribution bus voltages, a buck-type PFC rectifier is a logical solution. In this paper, an efficiency-optimized, 98.8% efficient, 5-kW three-phase buck-type PFC rectifier with 400-V output is presented. Methods for calculating losses of all components are described and are used to optimize the converter design for efficiency at full load. Special attention is paid to semiconductor losses, which are shown to be dominant, with the parasitic device capacitance losses being a significant component. The calculation of these parasitic capacitance losses is treated in detail, and the charge-balance approach used is verified. A prototype of the proposed rectifier is constructed which verifies the accuracy of the models used for loss calculation and optimization.
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 27 (4) , 1732-1744
Towards a 99% Efficient Three-Phase Buck-Type PFC Rectifier for 400-V DC Distribution Systems
In telecom applications, the vision for a total power conversion efficiency from the mains to the output of point-of-load (PoL) converters of 95% demands optimization of every conversion step, i.e., the power factor correction (PFC) rectifier front-end should show an outstanding efficiency in the range of 99%. For recently discussed 400-V dc distribution bus voltages, a buck-type PFC rectifier is a logical solution. In this paper, an efficiency-optimized, 98.8% efficient, 5-kW three-phase buck-type PFC rectifier with 400-V output is presented. Methods for calculating losses of all components are described and are used to optimize the converter design for efficiency at full load. Special attention is paid to semiconductor losses, which are shown to be dominant, with the parasitic device capacitance losses being a significant component. The calculation of these parasitic capacitance losses is treated in detail, and the charge-balance approach used is verified. A prototype of the proposed rectifier is constructed which verifies the accuracy of the models used for loss calculation and optimization.
- 7 March 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 1 (4) , 528-535
Analysis of Theoretical Limits of Forced-Air Cooling Using Advanced Composite Materials With High Thermal Conductivities
Cooling systems take a significant portion of the total mass and/or volume of power electronic systems. In order to design a converter with high power density, it is necessary to minimize the converter's cooling system volume for a given maximum tolerable thermal resistance. This paper theoretically investigates whether the cooling system volume can be significantly reduced by employing new advanced composite materials like isotropic aluminum/diamond composites or anisotropic highly orientated pyrolytic graphite. Another strategy to improve the power density of the cooling system is to increase the rotating speed and/or the diameter of the fan, which is limited by increasing power consumption of the fan. Fan scaling laws are employed in order to describe volume and thermal resistance of an optimized cooling system (fan plus heat sink), resulting in a single compact equation dependent on just two design parameters. Based on this equation, a deep insight into different design strategies and their general potentials is possible. The theory of the design process is verified experimentally for cooling a 10 kW converter. Further experimental results showing the result of the operation of the optimized heat sink are also presented.
- 7 March 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 1 (4) , 528-535
Analysis of Theoretical Limits of Forced-Air Cooling Using Advanced Composite Materials With High Thermal Conductivities
Cooling systems take a significant portion of the total mass and/or volume of power electronic systems. In order to design a converter with high power density, it is necessary to minimize the converter's cooling system volume for a given maximum tolerable thermal resistance. This paper theoretically investigates whether the cooling system volume can be significantly reduced by employing new advanced composite materials like isotropic aluminum/diamond composites or anisotropic highly orientated pyrolytic graphite. Another strategy to improve the power density of the cooling system is to increase the rotating speed and/or the diameter of the fan, which is limited by increasing power consumption of the fan. Fan scaling laws are employed in order to describe volume and thermal resistance of an optimized cooling system (fan plus heat sink), resulting in a single compact equation dependent on just two design parameters. Based on this equation, a deep insight into different design strategies and their general potentials is possible. The theory of the design process is verified experimentally for cooling a 10 kW converter. Further experimental results showing the result of the operation of the optimized heat sink are also presented.
- 1 March 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 585-592
Sensitivity of telecom dc-dc converter optimization to the level of detail of the system model
Efficient power conversion is one of the fundamental research drivers for modern power supplies. In order to achieve and design on the edge of the system performance space, automatic optimization procedures based on comprehensive analytical converter operation and loss models have to be employed. In this paper, a 5kW, 400V to 46-56V phase-shift dc-dc converter with LC output filter is optimized for the highest possible full-load efficiency. The system performance is discussed and compared for full-load, half-load and part-load optimization. Furthermore, the complexity of the first applied comprehensive analytical models is reduced step by step and the resulting values of the design parameters and the system performance are compared in detail with the reference system optimized with the comprehensive models. The sensitivity of the optimization to the level of detail of the modeling as well as the possibilities of the model-complexity reduction is explained. It is shown that certain complex components of the system model can be omitted without noticeably affecting the resulting efficiency.
- 1 March 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 585-592
Sensitivity of telecom dc-dc converter optimization to the level of detail of the system model
Efficient power conversion is one of the fundamental research drivers for modern power supplies. In order to achieve and design on the edge of the system performance space, automatic optimization procedures based on comprehensive analytical converter operation and loss models have to be employed. In this paper, a 5kW, 400V to 46-56V phase-shift dc-dc converter with LC output filter is optimized for the highest possible full-load efficiency. The system performance is discussed and compared for full-load, half-load and part-load optimization. Furthermore, the complexity of the first applied comprehensive analytical models is reduced step by step and the resulting values of the design parameters and the system performance are compared in detail with the reference system optimized with the comprehensive models. The sensitivity of the optimization to the level of detail of the modeling as well as the possibilities of the model-complexity reduction is explained. It is shown that certain complex components of the system model can be omitted without noticeably affecting the resulting efficiency.
- 1 March 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 4 (10482334) , 505-512
Towards a 99% efficient three-phase buck-type PFC rectifier for 400 V DC distribution systems
In telecom applications, the vision for a total power conversion efficiency from the mains to the output of PoL converters of 95% demands for an optimization of every conversion step, i.e. the PFC rectifier front-end should show an outstanding efficiency in the range of 99%. For recently discussed 400 V DC distribution bus voltages a buck-type PFC rectifier is a logical solution. In this paper, an efficiency-optimized, nearly 99% efficient, 5 kW three-phase buck-type PFC rectifier with 400 V output is presented. Methods for calculating losses of all components are described, and are used to optimize the converter design for efficiency at full load. Special attention is paid to semiconductor losses, which are shown to be dominant, with the parasitic device capacitance losses being a significant component. A prototype of the proposed rectifier is constructed which verifies the accuracy of the models used for loss calculation and optimization.
- 1 March 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 4 (10482334) , 505-512
Towards a 99% efficient three-phase buck-type PFC rectifier for 400 V DC distribution systems
In telecom applications, the vision for a total power conversion efficiency from the mains to the output of PoL converters of 95% demands for an optimization of every conversion step, i.e. the PFC rectifier front-end should show an outstanding efficiency in the range of 99%. For recently discussed 400 V DC distribution bus voltages a buck-type PFC rectifier is a logical solution. In this paper, an efficiency-optimized, nearly 99% efficient, 5 kW three-phase buck-type PFC rectifier with 400 V output is presented. Methods for calculating losses of all components are described, and are used to optimize the converter design for efficiency at full load. Special attention is paid to semiconductor losses, which are shown to be dominant, with the parasitic device capacitance losses being a significant component. A prototype of the proposed rectifier is constructed which verifies the accuracy of the models used for loss calculation and optimization.
- 1 June 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 962-969
Advanced setup for thermal cycling of power modules following definable junction temperature profiles
In this paper a setup for performing power cycling tests of IGBT modules for the purpose of reliability analysis is presented. The main purpose of the setup is to provide experimental data for the parameterization and verification of a newly developed physical model of solder deformation leading to the failure of power electronic devices. The design procedure, including considerations of reliability, measurement, and cooling, for a 5 kW flexible power cycling system is presented. Experimental results of a sub-1 kW prototype setup are shown, demonstrating the ability of the system to force the junction temperature of the device under test to follow an arbitrary temperature profile.
- 1 June 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 962-969
Advanced setup for thermal cycling of power modules following definable junction temperature profiles
In this paper a setup for performing power cycling tests of IGBT modules for the purpose of reliability analysis is presented. The main purpose of the setup is to provide experimental data for the parameterization and verification of a newly developed physical model of solder deformation leading to the failure of power electronic devices. The design procedure, including considerations of reliability, measurement, and cooling, for a 5 kW flexible power cycling system is presented. Experimental results of a sub-1 kW prototype setup are shown, demonstrating the ability of the system to force the junction temperature of the device under test to follow an arbitrary temperature profile.
- 1 June 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02759306,p. 3950-3954
Digitally-controlled steered-inductor buck converter for improving heavy-to-light load transient response
In this paper a novel digital controller and modified buck converter for improving heavy-to-light load transient response of low-power low-voltage dc-dc converters is introduced. The system is primarily designed for point-of-load (PoL) converters providing low regulated voltages for digital loads. In conventional buck topologies, the low output voltage, often below 1 V, severely limits the inductor current slew rate during the transients. To overcome this physical limitation, a modification is introduced whereby during heavy-to-light transients, the inductor current is, by the means of two extra switches, steered into the source and at the same time, the slew-rate of the current is significantly increased. The steering action is governed by a digital controller. The effectiveness of the system is verified on an FPGA-controlled, 12 V to 0.9 V, 10 W, experimental prototype. The results show that the steered-inductor digitally controlled buck converter has much shorter settling time and provides 2.8 times smaller overshoot than the conventional buck.
- 1 June 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02759306,p. 3950-3954
Digitally-controlled steered-inductor buck converter for improving heavy-to-light load transient response
In this paper a novel digital controller and modified buck converter for improving heavy-to-light load transient response of low-power low-voltage dc-dc converters is introduced. The system is primarily designed for point-of-load (PoL) converters providing low regulated voltages for digital loads. In conventional buck topologies, the low output voltage, often below 1 V, severely limits the inductor current slew rate during the transients. To overcome this physical limitation, a modification is introduced whereby during heavy-to-light transients, the inductor current is, by the means of two extra switches, steered into the source and at the same time, the slew-rate of the current is significantly increased. The steering action is governed by a digital controller. The effectiveness of the system is verified on an FPGA-controlled, 12 V to 0.9 V, 10 W, experimental prototype. The results show that the steered-inductor digitally controlled buck converter has much shorter settling time and provides 2.8 times smaller overshoot than the conventional buck.