Pavel V. Fursikov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Pavel V. Fursikov has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
B. P. Tarasov
Federal Research Center of Problems of Chemical Physics and Medicinal Chemistry, Russian Academy of Sciences, Chernogolovka, Russia
6 shared publicationsA. A. Arbuzov
Federal Research Center of Problems of Chemical Physics and Medicinal Chemistry, Russian Academy of Sciences, Chernogolovka, Russia
4 shared publicationsE. E. Fokina
Federal Research Center of Problems of Chemical Physics and Medicinal Chemistry, Russian Academy of Sciences, Chernogolovka, Russia
4 shared publicationsV. N. Fokin
Federal Research Center of Problems of Chemical Physics and Medicinal Chemistry, Russian Academy of Sciences, Chernogolovka, Russia
4 shared publicationsI. I. Khodos
Institute of Microelectronics Technology and High Purity Materials, Russian Academy of Sciences, Chernogolovka, Russia
3 shared publicationsS. A. Mozhzhukhin
Federal Research Center of Problems of Chemical Physics and Medicinal Chemistry, Russian Academy of Sciences, Chernogolovka, Moscow oblast, Russia
2 shared publications
Latest Publications
- 1 December 2024
- Published by Pleiades Publishing Ltd in High Energy Chemistry
- Vol. 58 (S4) , S491-S495
Phase Transformations and Kinetics Peculiarities on Hydrogen Desorption by Composites Based in Magnesium–Nickel Eutectic Alloy
The evolution of the phase contents and kinetic characteristics of hydrogen desorption processes by composites based on the eutectic alloy Mg89Ni11, including those with additives of graphene-like material (GLM), obtained by reactive ball-milling in hydrogen, were studied using the in situ high-temperature X-ray diffraction technique, volumetric measurements on a Sieverts setup, and approximation of the registered kinetic curves by Avrami−Erofeev equation. It was shown that at the initial stage of desorption processes at 300–360°C and 0–1 atm. H2, the decomposition of the magnesium dihydride phase makes the main contribution to the amount of hydrogen released from the composites. The addition of GLM has a positive effect on the kinetics of hydrogen desorption processes, concurring with that of the heat-conducting phase Mg2NiH≤0.3, which is also present in the composite. It was found that the apparent activation energy for the hydrogen desorption by composites is within a range of 125–140 kJ/mol H2. The correlation of the obtained values with the results of both experimental studies and quantum-chemical calculations obtained in the study of other magnesium systems is discussed.
- 1 December 2024
- Published by Pleiades Publishing Ltd in High Energy Chemistry
- Vol. 58 (S4) , S491-S495
Phase Transformations and Kinetics Peculiarities on Hydrogen Desorption by Composites Based in Magnesium–Nickel Eutectic Alloy
The evolution of the phase contents and kinetic characteristics of hydrogen desorption processes by composites based on the eutectic alloy Mg89Ni11, including those with additives of graphene-like material (GLM), obtained by reactive ball-milling in hydrogen, were studied using the in situ high-temperature X-ray diffraction technique, volumetric measurements on a Sieverts setup, and approximation of the registered kinetic curves by Avrami−Erofeev equation. It was shown that at the initial stage of desorption processes at 300–360°C and 0–1 atm. H2, the decomposition of the magnesium dihydride phase makes the main contribution to the amount of hydrogen released from the composites. The addition of GLM has a positive effect on the kinetics of hydrogen desorption processes, concurring with that of the heat-conducting phase Mg2NiH≤0.3, which is also present in the composite. It was found that the apparent activation energy for the hydrogen desorption by composites is within a range of 125–140 kJ/mol H2. The correlation of the obtained values with the results of both experimental studies and quantum-chemical calculations obtained in the study of other magnesium systems is discussed.
- 23 December 2023
- Published by Pleiades Publishing Ltd in High Energy Chemistry
- Vol. 57 (S2) , S310-S315
Microstructure of Hydrogenated Magnesium–Nickel Eutectic Alloy Based Composites and its Changes during Hydrogen Absorption/Desorption Cycling
In this work, we studied phase composition, hydrogen desorption kinetics and microstructural topology of hydrogen-sorbing composite materials prepared by ball milling under hydrogen of the powders of Mg89Ni11 eutectic alloy without and with additive of graphene-like material (GLM). It was shown that in both cases the reproducible fast desorption kinetics were achieved after the fifth dehydrogenation—re-hydrogenation cycle. Using transmission electron microscopy, selected area electron diffraction, and the effect of MgH2 radiolysis it was found that after seven hydrogenation–dehydrogenation cycles the material retains a highly dispersed microstructure: in the regions with a cross-sectional area of 1 micron in the size there are grains of Mg and Mg2Ni hydride-forming phases that are in direct contact, that favors the hydrogen sorption performance of the material.
- 23 December 2023
- Published by Pleiades Publishing Ltd in High Energy Chemistry
- Vol. 57 (S2) , S310-S315
Microstructure of Hydrogenated Magnesium–Nickel Eutectic Alloy Based Composites and its Changes during Hydrogen Absorption/Desorption Cycling
In this work, we studied phase composition, hydrogen desorption kinetics and microstructural topology of hydrogen-sorbing composite materials prepared by ball milling under hydrogen of the powders of Mg89Ni11 eutectic alloy without and with additive of graphene-like material (GLM). It was shown that in both cases the reproducible fast desorption kinetics were achieved after the fifth dehydrogenation—re-hydrogenation cycle. Using transmission electron microscopy, selected area electron diffraction, and the effect of MgH2 radiolysis it was found that after seven hydrogenation–dehydrogenation cycles the material retains a highly dispersed microstructure: in the regions with a cross-sectional area of 1 micron in the size there are grains of Mg and Mg2Ni hydride-forming phases that are in direct contact, that favors the hydrogen sorption performance of the material.
- Open Access
- 6 July 2023
- Published by MDPI AG in Inorganics
- Vol. 11 (7) , 290
Metal Hydride Hydrogen Storage (Compression) Units Operating at Near-Atmospheric Pressure of the Feed H2
Metal hydride (MH) hydrogen storage and compression systems with near-atmospheric H2 suction pressure are necessary for the utilization of the low-pressure H2 produced by solid oxide electrolyzers or released as a byproduct of chemical industries. Such systems should provide reasonably high productivity in the modes of both charge (H2 absorption at PL ≤ 1 atm) and discharge (H2 desorption at PH = 2–5 atm), which implies the provision of H2 equilibrium pressures Peq < PL at the available cooling temperature (TL = 15–20 °C) and, at the same time, Peq > PH when heated to TH = 90–150 °C. This work presents results of the development of such systems based on AB5-type intermetallics characterized by Peq of 0.1–0.3 atm and 3–8 atm for H2 absorption at TL = 15 °C and H2 desorption at TH = 100 °C, respectively. The MH powders mixed with 1 wt.% of Ni-doped graphene-like material or expanded natural graphite for the improvement of H2 charge dynamics were loaded in a cylindrical container equipped with internal and external heat exchangers. The developed units with a capacity of about 1 Nm3 H2 were shown to exhibit H2 flow rates above 10 NL/min during H2 charge at ≤1 atm when cooled to ≤20 °C with cold water and H2 release at a pressure above 2 and 5 atm when heated to 90 and 120 °C with hot water and steam, respectively.
- 6 July 2023
- Published by MDPI AG in Inorganics
- Vol. 11 (7) , 290
Open AccessMetal Hydride Hydrogen Storage (Compression) Units Operating at Near-Atmospheric Pressure of the Feed H2
Metal hydride (MH) hydrogen storage and compression systems with near-atmospheric H2 suction pressure are necessary for the utilization of the low-pressure H2 produced by solid oxide electrolyzers or released as a byproduct of chemical industries. Such systems should provide reasonably high productivity in the modes of both charge (H2 absorption at PL ≤ 1 atm) and discharge (H2 desorption at PH = 2–5 atm), which implies the provision of H2 equilibrium pressures Peq < PL at the available cooling temperature (TL = 15–20 °C) and, at the same time, Peq > PH when heated to TH = 90–150 °C. This work presents results of the development of such systems based on AB5-type intermetallics characterized by Peq of 0.1–0.3 atm and 3–8 atm for H2 absorption at TL = 15 °C and H2 desorption at TH = 100 °C, respectively. The MH powders mixed with 1 wt.% of Ni-doped graphene-like material or expanded natural graphite for the improvement of H2 charge dynamics were loaded in a cylindrical container equipped with internal and external heat exchangers. The developed units with a capacity of about 1 Nm3 H2 were shown to exhibit H2 flow rates above 10 NL/min during H2 charge at ≤1 atm when cooled to ≤20 °C with cold water and H2 release at a pressure above 2 and 5 atm when heated to 90 and 120 °C with hot water and steam, respectively.
- 1 August 2022
- Published by Pleiades Publishing Ltd in Russian Journal of Applied Chemistry
- Vol. 95 (8) , 1141-1145
Microstructure of Hydrogen-Sorbing Composites Based on a Eutectic Magnesium Alloy with Nickel
Using transmission electron microscopy (TEM) and electron microdiffraction with the radiolysis effect and a series of calibration images of TEM obtained for single-phase MgH2 samples at different exposure times, we studied the topological features of the microstructure of powder hydrogen-sorbing composites based on the Mg89Ni11 eutectic alloy. It was found that after several hydrogenation–dehydrogenation cycles the composite retains a highly dispersed microstructure: in the regions of composite samples with a cross-sectional area of 1 μm2 there are grains of Mg and Mg2Ni hydride-forming phases that are in direct contact, which improves the hydrogen-sorbing characteristics of the composite.
- 1 August 2022
- Published by Pleiades Publishing Ltd in Russian Journal of Applied Chemistry
- Vol. 95 (8) , 1141-1145
Microstructure of Hydrogen-Sorbing Composites Based on a Eutectic Magnesium Alloy with Nickel
Using transmission electron microscopy (TEM) and electron microdiffraction with the radiolysis effect and a series of calibration images of TEM obtained for single-phase MgH2 samples at different exposure times, we studied the topological features of the microstructure of powder hydrogen-sorbing composites based on the Mg89Ni11 eutectic alloy. It was found that after several hydrogenation–dehydrogenation cycles the composite retains a highly dispersed microstructure: in the regions of composite samples with a cross-sectional area of 1 μm2 there are grains of Mg and Mg2Ni hydride-forming phases that are in direct contact, which improves the hydrogen-sorbing characteristics of the composite.
- 7 May 2020
- Published by Pleiades Publishing Ltd in Russian Journal of Physical Chemistry A
- Vol. 94 (5) , 1011-1016
Phase Composition and Microstructure of Mg–Ni Eutectic Alloy with Graphene-Like Material for Hydrogen Adsorption
Powder composites of hydrogenated eutectic Mg–Ni alloy with 10 wt % graphene-like material (GLM) were prepared mechanochemically at a hydrogen pressure of 30 atm. The effect that adding GLM, along with 10 cycles of desorption at 350°C and 1 atm and sorption at 300°C and 10 atm of hydrogen, has on the phase composition and microstructure of the composites is studied. It is shown that composites obtained mechanochemically (hbm composites) and subjected to cycles of hydrogen desorption–adsorption (dh composites) contain crystalline phases: α-MgH2 with rutile-type structure, Mg2NiH4 hydride with a disordered cubic structure (pseudo-ht-Mg2NiH4), and a solid solution of hydrogen Mg2NiH≤0.3. It is found that in hbm composites with GLM additives, the content of the pseudo-ht-Mg2Ni phase is higher than in composites without carbon additives. The Mg2Ni(H) and Mg(H) particles have a common boundary in composites, and cycling does not affect these features of the microstructure. The presence of GLM preserves the small particle sizes of both phases during cycling.
- 7 May 2020
- Published by Pleiades Publishing Ltd in Russian Journal of Physical Chemistry A
- Vol. 94 (5) , 1011-1016
Phase Composition and Microstructure of Mg–Ni Eutectic Alloy with Graphene-Like Material for Hydrogen Adsorption
Powder composites of hydrogenated eutectic Mg–Ni alloy with 10 wt % graphene-like material (GLM) were prepared mechanochemically at a hydrogen pressure of 30 atm. The effect that adding GLM, along with 10 cycles of desorption at 350°C and 1 atm and sorption at 300°C and 10 atm of hydrogen, has on the phase composition and microstructure of the composites is studied. It is shown that composites obtained mechanochemically (hbm composites) and subjected to cycles of hydrogen desorption–adsorption (dh composites) contain crystalline phases: α-MgH2 with rutile-type structure, Mg2NiH4 hydride with a disordered cubic structure (pseudo-ht-Mg2NiH4), and a solid solution of hydrogen Mg2NiH≤0.3. It is found that in hbm composites with GLM additives, the content of the pseudo-ht-Mg2Ni phase is higher than in composites without carbon additives. The Mg2Ni(H) and Mg(H) particles have a common boundary in composites, and cycling does not affect these features of the microstructure. The presence of GLM preserves the small particle sizes of both phases during cycling.
- 1 February 2018
- Published by Springer Nature in Russian Chemical Bulletin
- Vol. 67 (2) , 193-199
Hydrogen sorbing magnesium alloys and composites
- 1 February 2018
- Published by Springer Nature in Russian Chemical Bulletin
- Vol. 67 (2) , 193-199
Hydrogen sorbing magnesium alloys and composites
- 1 September 2011
- Published by Springer Nature in Russian Chemical Bulletin
- Vol. 60 (9) , 1848-1857
Hydrogenation of nanostructured alloys and composites based on magnesium
- 1 September 2011
- Published by Springer Nature in Russian Chemical Bulletin
- Vol. 60 (9) , 1848-1857
Hydrogenation of nanostructured alloys and composites based on magnesium
- 1 January 2011
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 36 (1) , 1326-1329
Influence of carbonaceous additives on hydrogen sorption properties of Mg–RE–Ni “pseudoalloys”
- 1 January 2011
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 36 (1) , 1326-1329
Influence of carbonaceous additives on hydrogen sorption properties of Mg–RE–Ni “pseudoalloys”