Y. C. Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Y. C. Zhou has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
X. J. Zheng
Xiangtan University
2 shared publicationsA. D. Li
Nanjing University
1 shared publicationA.D. Li
Laboratory of Solid State Microstructures, Nanjing University, Nanjing, China
1 shared publicationC. Q. Yang
Institute of Fundamental Mechanics and Material Engineering, Physics Department, Xiangtan University, Xiangtan, Hunan, 411105, China
1 shared publication- Greg Bignall
GNS Science
1 shared publication J. M. Liu
Nanjing University
1 shared publication
Latest Publications
- 31 October 2003
- Published by Elsevier in Mechanics of Materials
- Vol. 35 (10) , 1003-1020
Thermal failure mechanism and failure threshold of SiC particle reinforced metal matrix composites induced by laser beam
- 31 October 2003
- Published by Elsevier in Mechanics of Materials
- Vol. 35 (10) , 1003-1020
Thermal failure mechanism and failure threshold of SiC particle reinforced metal matrix composites induced by laser beam
- 1 May 2003
- Published by Springer Nature in Journal of Materials Science Letters
- Vol. 22 (10) , 743-745
Determination of interfacial fracture energy of PZT ferroelectric thin films by nano-scratch technique
- 1 May 2003
- Published by Springer Nature in Journal of Materials Science Letters
- Vol. 22 (10) , 743-745
Determination of interfacial fracture energy of PZT ferroelectric thin films by nano-scratch technique
- 11 November 2002
- Published by Elsevier in Physics Letters A
- Vol. 304 (3-4) , 110-113
Interfacial adhesion analysis of Pb(Zr0.52Ti0.48)O3 (PZT) thin films by nano-indentation test
- 11 November 2002
- Published by Elsevier in Physics Letters A
- Vol. 304 (3-4) , 110-113
Interfacial adhesion analysis of Pb(Zr0.52Ti0.48)O3 (PZT) thin films by nano-indentation test
- 1 October 2002
- Published by Springer Nature in Journal of Materials Science Letters
- Vol. 21 (19) , 1541-1544
Determination of residual stress in PZT thin film prepared by pulsed laser deposition
- 1 October 2002
- Published by Springer Nature in Journal of Materials Science Letters
- Vol. 21 (19) , 1541-1544
Determination of residual stress in PZT thin film prepared by pulsed laser deposition
- 1 January 2002
- Published by Taylor & Francis in Transactions of the IMF
- Vol. 80 (5) , 161-163
A sulphate bath for the preparation of Zn-Fe alloy coatings
A new acidic sulphate bath was developed for the preparation of Zn-Fe alloy coatings. The percentage of iron in the deposits produced was measured by atomic absorption spectrophotometry and was found to be below 1.0 wt%. The bath composition was easy to control and when citric acid and sodium citrate were employed as buffer and complexing agents, respectively, stable pH values were observed. In addition, the operation cost was low and the cathode efficiency was high with respect to the alkaline baths. The Zn-Fe alloy coatings produced were fine and iridescent and no pinholes or pores could be observed over the surface. The percentage of iron in the alloy coatings increased with the increase of metal ratio Fe2/Zn2, and the applied current density. Bend tests indicated that the alloy coalings had good adhesion strength to the substrate.
- 1 January 2002
- Published by Taylor & Francis in Transactions of the IMF
- Vol. 80 (5) , 161-163
A sulphate bath for the preparation of Zn-Fe alloy coatings
A new acidic sulphate bath was developed for the preparation of Zn-Fe alloy coatings. The percentage of iron in the deposits produced was measured by atomic absorption spectrophotometry and was found to be below 1.0 wt%. The bath composition was easy to control and when citric acid and sodium citrate were employed as buffer and complexing agents, respectively, stable pH values were observed. In addition, the operation cost was low and the cathode efficiency was high with respect to the alkaline baths. The Zn-Fe alloy coatings produced were fine and iridescent and no pinholes or pores could be observed over the surface. The percentage of iron in the alloy coatings increased with the increase of metal ratio Fe2/Zn2, and the applied current density. Bend tests indicated that the alloy coalings had good adhesion strength to the substrate.