Long Yu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Long Yu has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Qidong Fan
State Key Laboratory of Ocean Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
5 shared publications Jingjing Liu
4 shared publicationsLecheng Li
4 shared publicationsXiaoyan Li
3 shared publications- Zhiyuan Cai3 shared publications
Congbo Li
2 shared publications
Latest Publications
- 16 September 2026
- Published by Elsevier in Ocean Engineering
- Vol. 367
Research on dual coupling model for dynamic analysis of USV-assisted floating pipe docking for TSHDs
- 16 September 2026
- Published by Elsevier in Ocean Engineering
- Vol. 367
Research on dual coupling model for dynamic analysis of USV-assisted floating pipe docking for TSHDs
- Open Access
- 8 July 2026
- Published by Elsevier in SSRN Electronic Journal
Sister RoPax Hull Form Design Using a Data-Physics Dual-Driven Fuel Consumption Model Based on Parent Vessel Data: Part II Design and Operation Optimization
With the demands for green ship design for low CO2 emission, the Dual-Driven Fuel Consumption Model under Operational Scenarios for Ship Design (FCMOS) was developed in Part I of this study, which connected hull form design with fuel consumption prediction under operational routes and machinery constraints of the parent ship. Nevertheless, because the operational fuel consumption prediction relies on the historical data, dealing with the complex and flexible navigation routes while considering the speed optimization under weather variants at the design stage as a Design and Operation Optimization (D&O) remains a significant challenge. Accordingly, in this paper, a segmentation algorithm and a two-stage optimization are developed for optimal operational speed calculation based on FCMOS. First, we adopted the adaptive segmentation algorithm to divide the route into different legs. Then, the combined speed and hull form optimization was formulated as a finite-dimensional optimization problem. Finally, we investigated the solution and the results show that it could further reduce fuel consumption by a maximum of 3.15% relative to the baseline hull at different routes. The proposed method offers broad applicability for the hull form designs of sister vessels at the preliminary design stage.
- 8 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSister RoPax Hull Form Design Using a Data-Physics Dual-Driven Fuel Consumption Model Based on Parent Vessel Data: Part II Design and Operation Optimization
With the demands for green ship design for low CO2 emission, the Dual-Driven Fuel Consumption Model under Operational Scenarios for Ship Design (FCMOS) was developed in Part I of this study, which connected hull form design with fuel consumption prediction under operational routes and machinery constraints of the parent ship. Nevertheless, because the operational fuel consumption prediction relies on the historical data, dealing with the complex and flexible navigation routes while considering the speed optimization under weather variants at the design stage as a Design and Operation Optimization (D&O) remains a significant challenge. Accordingly, in this paper, a segmentation algorithm and a two-stage optimization are developed for optimal operational speed calculation based on FCMOS. First, we adopted the adaptive segmentation algorithm to divide the route into different legs. Then, the combined speed and hull form optimization was formulated as a finite-dimensional optimization problem. Finally, we investigated the solution and the results show that it could further reduce fuel consumption by a maximum of 3.15% relative to the baseline hull at different routes. The proposed method offers broad applicability for the hull form designs of sister vessels at the preliminary design stage.
- Open Access
- 20 April 2026
- Published by Elsevier in SSRN Electronic Journal
Identification of Cross-Flow Drag Distribution for Trailing Suction Hopper Dredger Using PINN
Trailing suction hopper dredgers (TSHDs) are characterized by their bulky hull forms. Traditional mathematical models based on Taylor series expansions lack sufficient predictive accuracy when estimating the hydrodynamic forces and maneuvering responses of such large vessels under highly nonlinear operating conditions, primarily due to the ambiguous physical interpretation of higher-order terms. To address this issue, this paper proposes a physics-informed neural network (PINN) hydrodynamic identification method that incorporates the cross-flow drag mechanism. A hybrid hydrodynamic model architecture combining linear potential flow with nonlinear cross-flow effects is developed. For longitudinal resistance, a polynomial model consistent with physical symmetry is retained; for lateral force and yaw moment, a cross-flow integral model based on strip theory is introduced. Utilizing a PINN network structure, the draft distribution function H(x) of the model ship’s hull geometry is explicitly embedded within the physical computation layer. Experimental data from large-amplitude oscillation tests conducted using a planar motion mechanism (PMM) were successfully employed to invert the cross-flow drag coefficient distribution along the ship’s length. The proposed model significantly enhances generalization ability and physical interpretability for large-amplitude roll and yaw motions, thereby providing a more reliable and physically consistent framework for predicting TSHD maneuvering behavior in complex sea conditions.
- 20 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessIdentification of Cross-Flow Drag Distribution for Trailing Suction Hopper Dredger Using PINN
Trailing suction hopper dredgers (TSHDs) are characterized by their bulky hull forms. Traditional mathematical models based on Taylor series expansions lack sufficient predictive accuracy when estimating the hydrodynamic forces and maneuvering responses of such large vessels under highly nonlinear operating conditions, primarily due to the ambiguous physical interpretation of higher-order terms. To address this issue, this paper proposes a physics-informed neural network (PINN) hydrodynamic identification method that incorporates the cross-flow drag mechanism. A hybrid hydrodynamic model architecture combining linear potential flow with nonlinear cross-flow effects is developed. For longitudinal resistance, a polynomial model consistent with physical symmetry is retained; for lateral force and yaw moment, a cross-flow integral model based on strip theory is introduced. Utilizing a PINN network structure, the draft distribution function H(x) of the model ship’s hull geometry is explicitly embedded within the physical computation layer. Experimental data from large-amplitude oscillation tests conducted using a planar motion mechanism (PMM) were successfully employed to invert the cross-flow drag coefficient distribution along the ship’s length. The proposed model significantly enhances generalization ability and physical interpretability for large-amplitude roll and yaw motions, thereby providing a more reliable and physically consistent framework for predicting TSHD maneuvering behavior in complex sea conditions.
- 13 May 2025
- Published by Elsevier in Applied Acoustics
- Vol. 238
Error analysis and control of the acoustic overlapping mesh technique
- 13 May 2025
- Published by Elsevier in Applied Acoustics
- Vol. 238
Error analysis and control of the acoustic overlapping mesh technique
- 11 August 2024
- Published by Elsevier in Ocean Engineering
- Vol. 311
An efficient Meta-VSW method for ship behaviors recognition and application
- 11 August 2024
- Published by Elsevier in Ocean Engineering
- Vol. 311
An efficient Meta-VSW method for ship behaviors recognition and application
- Open Access
- 12 June 2024
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 12 (6) , 986
Numerical and Experimental Analysis of Lifting Forces of Fin Stabilizers with Fin–Hull Interaction
A fin stabilizer is one of the most effective and frequently used anti-roll devices for maintaining a ship’s operational safety and passengers’ comfort. However, the discrepancy between theoretical hydrofoil-based predictions and the actual dynamic lift force of fin stabilizers due to fin–hull interactions requires more research attention. This study investigates the effect of fin stabilizers on mitigating roll motion through the performance of extensive computational fluid dynamic (CFD) simulations over a range of fin angles and ship speeds. Model tests were carried out to validate the drag and motion results obtained from numerical analyses. The results show that fin stabilizers significantly reduce the roll motion, with the lift coefficient values influenced by the Reynolds number, leading to differences between the theoretical and Reynolds-averaged Navier–Stokes (RANS) calculations. At a high Froude number (Fr), the actual fin lift is about half of the theoretical value. These findings highlight the requirement of selecting an adequate fin area at the predominant ship speeds and ensuring an effective anti-roll effect with fin–hull interaction. This study provides a significant reference for ship design, as well as stabilization system control and optimization.
- 12 June 2024
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 12 (6) , 986
Open AccessNumerical and Experimental Analysis of Lifting Forces of Fin Stabilizers with Fin–Hull Interaction
A fin stabilizer is one of the most effective and frequently used anti-roll devices for maintaining a ship’s operational safety and passengers’ comfort. However, the discrepancy between theoretical hydrofoil-based predictions and the actual dynamic lift force of fin stabilizers due to fin–hull interactions requires more research attention. This study investigates the effect of fin stabilizers on mitigating roll motion through the performance of extensive computational fluid dynamic (CFD) simulations over a range of fin angles and ship speeds. Model tests were carried out to validate the drag and motion results obtained from numerical analyses. The results show that fin stabilizers significantly reduce the roll motion, with the lift coefficient values influenced by the Reynolds number, leading to differences between the theoretical and Reynolds-averaged Navier–Stokes (RANS) calculations. At a high Froude number (Fr), the actual fin lift is about half of the theoretical value. These findings highlight the requirement of selecting an adequate fin area at the predominant ship speeds and ensuring an effective anti-roll effect with fin–hull interaction. This study provides a significant reference for ship design, as well as stabilization system control and optimization.
- Open Access
- 27 February 2024
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 12 (3) , 421
An Equivalent Linear Method to Predict Nonlinear Bending Mechanics of Dredging Floating Hose String
Dredging hoses are flexible and are particularly suitable for slurry transportations for mud or sand in dredging projects. To achieve sufficient bending stiffness and to prevent the pipe body from collapsing, this type of hose segment is a composite structure that is embedded with several cord reinforcement layers and steel wires in its rubber layer. To quickly evaluate the nonlinear bending mechanical properties of rubber hoses, this study proposes the equivalent stiffness method of linear superposition, which is verified by test data and numerical results. The results show that the equivalent bending stiffness method proposed in this study is in good agreement with numerical and experimental results. Then, by comparing the calculation results of the hose string, it was demonstrated that the linear stiffness superposition method proposed in this study can also accurately predict the bending mechanical behavior characteristics of string hose, and provide reliable guidance for hose design in practice.
- 27 February 2024
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 12 (3) , 421
Open AccessAn Equivalent Linear Method to Predict Nonlinear Bending Mechanics of Dredging Floating Hose String
Dredging hoses are flexible and are particularly suitable for slurry transportations for mud or sand in dredging projects. To achieve sufficient bending stiffness and to prevent the pipe body from collapsing, this type of hose segment is a composite structure that is embedded with several cord reinforcement layers and steel wires in its rubber layer. To quickly evaluate the nonlinear bending mechanical properties of rubber hoses, this study proposes the equivalent stiffness method of linear superposition, which is verified by test data and numerical results. The results show that the equivalent bending stiffness method proposed in this study is in good agreement with numerical and experimental results. Then, by comparing the calculation results of the hose string, it was demonstrated that the linear stiffness superposition method proposed in this study can also accurately predict the bending mechanical behavior characteristics of string hose, and provide reliable guidance for hose design in practice.