M K Al-Mosawi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
M K Al-Mosawi has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
C Beduz
School of Engineering Sciences, University of Southampton, Southampton, SO171BJ, UK
4 shared publicationsY Yang
School of Engineering Sciences, University of Southampton, Southampton, SO171BJ, UK
4 shared publicationsB Xu
Mechanical Engineering, School of Engineering Sciences, University of Southampton, Southampton SO17 1BJ, UK
2 shared publicationsK Goddard
School of Engineering Sciences, University of Southampton, Southampton, SO171BJ, UK
2 shared publicationsA Ballarino
CERN, European Organization for Nuclear, Switzerland
1 shared publication- Jan. K. Sykulski
School of Electronics and Computer Science, University of Southampton, Southampton, United Kingdom
1 shared publication
Latest Publications
- 1 February 2008
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 97 (1) , 012304
Quench characteristics of Ag/AuBi2223 HTS-stainless steel stack used for the hybrid current leads of the large hadron collider
The quench characteristics of Ag/Au sheathed Bi2223 tapes have been investigated in an adiabatic condition and in a configuration similar to that used in hybrid high temperature superconducting current leads, namely the 13000A leads used for the Large Hadron Collider at CERN. A specialised rig was designed and constructed to provide a carefully controlled environment. The samples were prepared from HTS tape soldered onto a stainless steel substrate with a number of temperature sensors at various positions along the length of tape. One end of the lead (cold end) was maintained at 6K using G-M cryo-cooler whereas the temperature of the other end (warm end) can be varied and maintained at temperatures up to 100K. The thermal runaway currents (quench currents) at various warm end temperatures (in the range of 40-100K) were determined. The temperature evolutions at various locations along the tape were recorded at different top end temperatures and currents. The effect of the stainless steel mechanical reinforcement on the thermal properties of the stack was also investigated and presented.
- 1 February 2008
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 97 (1) , 012304
Quench characteristics of Ag/AuBi2223 HTS-stainless steel stack used for the hybrid current leads of the large hadron collider
The quench characteristics of Ag/Au sheathed Bi2223 tapes have been investigated in an adiabatic condition and in a configuration similar to that used in hybrid high temperature superconducting current leads, namely the 13000A leads used for the Large Hadron Collider at CERN. A specialised rig was designed and constructed to provide a carefully controlled environment. The samples were prepared from HTS tape soldered onto a stainless steel substrate with a number of temperature sensors at various positions along the length of tape. One end of the lead (cold end) was maintained at 6K using G-M cryo-cooler whereas the temperature of the other end (warm end) can be varied and maintained at temperatures up to 100K. The thermal runaway currents (quench currents) at various warm end temperatures (in the range of 40-100K) were determined. The temperature evolutions at various locations along the tape were recorded at different top end temperatures and currents. The effect of the stainless steel mechanical reinforcement on the thermal properties of the stack was also investigated and presented.
- 1 February 2008
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 97 (1) , 012205
Development of a coreless HTS synchronous generator operating at sub-cooled liquid nitrogen temperatures
This paper presents the current design concepts for a 100kW high temperature superconducting synchronous generator currently being designed at the University of Southampton, UK. The new generator will use the same conventional 2-pole 3-phase stator that was used in the HTS synchronous generator previously constructed at Southampton. The windings consist of 18 pancake coils made from BiPb2223 superconducting tape with a nominal current of 180A at 77K, provided by Sumitomo Electric Industries, Ltd. Tests were performed to determine the mechanical strain limits of the tape. The rotor has no central core, but magnetic pole pieces are used to improve the waveform of the generator. The coils are separated by magnetic diverter rings to reduce the normal field in the tape. The coils and diverter rings are supported by fibreglass formers that extend to the centre of the rotor so that they can be located by the through bolts that hold the stack together. A stainless steel tube encapsulates the rotor to provide a chamber for liquid nitrogen to flood the rotor.
- 1 February 2008
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 97 (1) , 012205
Development of a coreless HTS synchronous generator operating at sub-cooled liquid nitrogen temperatures
This paper presents the current design concepts for a 100kW high temperature superconducting synchronous generator currently being designed at the University of Southampton, UK. The new generator will use the same conventional 2-pole 3-phase stator that was used in the HTS synchronous generator previously constructed at Southampton. The windings consist of 18 pancake coils made from BiPb2223 superconducting tape with a nominal current of 180A at 77K, provided by Sumitomo Electric Industries, Ltd. Tests were performed to determine the mechanical strain limits of the tape. The rotor has no central core, but magnetic pole pieces are used to improve the waveform of the generator. The coils are separated by magnetic diverter rings to reduce the normal field in the tape. The coils and diverter rings are supported by fibreglass formers that extend to the centre of the rotor so that they can be located by the through bolts that hold the stack together. A stainless steel tube encapsulates the rotor to provide a chamber for liquid nitrogen to flood the rotor.
- Open Access
- 1 June 2006
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 43 (1) , 543-546
Improvement Mechanism and Bending Strain Tolerance for Reinforced Bi2223 Superconducting Tapes
Comprehensive mechanical characterisation of stainless steel reinforced Bi2223 superconducting tapes was conducted using purpose built rigs. This included the effect of axial (tensile and compressive) and bending strain on the critical current (Ic) of reinforced Bi2223 tape. In addition, the axial tensile and transverse compressive stress properties of the tape were measured and evaluated. It was found that the Ic-bending strain characteristic of the tape was improved as a result of sheath reinforcement, compared to an identical tape without reinforcement. A mechanism for this improvement based on the homogenising effect of the reinforcement on strain is proposed. To avoid Ic degradation, the maximum axial stress on the reinforced tape should not exceed 350 MPa, or the tensile strain should be less than 0.65%. Furthermore, no Ic degradation was observed for transverse compressive stresses up to 100 MPa, while an axial compressive strain of about 0.3% causes about 10% drop in the critical current.
- 1 June 2006
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 43 (1) , 543-546
Open AccessImprovement Mechanism and Bending Strain Tolerance for Reinforced Bi2223 Superconducting Tapes
Comprehensive mechanical characterisation of stainless steel reinforced Bi2223 superconducting tapes was conducted using purpose built rigs. This included the effect of axial (tensile and compressive) and bending strain on the critical current (Ic) of reinforced Bi2223 tape. In addition, the axial tensile and transverse compressive stress properties of the tape were measured and evaluated. It was found that the Ic-bending strain characteristic of the tape was improved as a result of sheath reinforcement, compared to an identical tape without reinforcement. A mechanism for this improvement based on the homogenising effect of the reinforcement on strain is proposed. To avoid Ic degradation, the maximum axial stress on the reinforced tape should not exceed 350 MPa, or the tensile strain should be less than 0.65%. Furthermore, no Ic degradation was observed for transverse compressive stresses up to 100 MPa, while an axial compressive strain of about 0.3% causes about 10% drop in the critical current.
- 31 August 2002
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 372-376, 1539-1542
Design of a 100 kVA high temperature superconducting demonstration synchronous generator
- 31 August 2002
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 372-376, 1539-1542
Design of a 100 kVA high temperature superconducting demonstration synchronous generator