Volker Häublein
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Volker Häublein has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Michael I. Current
Current Scientific
3 shared publications- Leonard Rubin
Axcelis Technologies, Inc
2 shared publications - Mathias Rommel
Fraunhofer Institute for Integrated Systems and Device Technology IISB Erlangen Germany
2 shared publications - Birgit Kallinger
Fraunhofer IISB
1 shared publication - Chiao Yu Liu
Semilab Semiconductor Physics Laboratory Co. Ltd
1 shared publication - David A. Kirkwood
Axcelis Technologies, Inc
1 shared publication
Latest Publications
- 4 September 2026
- Published by Springer Nature
- p. 345-391
Ion Beam Purity and Wafer Contamination
- 4 September 2026
- Published by Springer Nature
- p. 243-344
Metrology for Ion Implantation Process Control
- 4 September 2026
- Published by Springer Nature
- p. 243-344
Metrology for Ion Implantation Process Control
- 4 September 2026
- Published by Springer Nature
- p. 139-186
Commercial Ion Implantation Systems
- 4 September 2026
- Published by Springer Nature
- p. 585-640
Ion Channeling Effects in Silicon and Silicon Carbide
- 4 September 2026
- Published by Springer Nature
- p. 585-640
Ion Channeling Effects in Silicon and Silicon Carbide
- Open Access
- 19 May 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1191, 29-35
Evaluation of Oxide Processing Steps in SiC Technology Using Contactless Corona-Based CV Measurements
An area of increasing interest for SiC device processing is the processing and qualification of silicon oxides. In this article a contactless corona CV (CnCV) measurement procedure is evaluated as a way to gain more knowledge about the different processes related to oxides. A 21-point measurement pattern is used to gain information about uniformity of oxide properties. Two different types of oxides have been considered, low pressure chemical vapor deposited (CVD) oxides using tetraethylorthosilicate (TEOS) and thermally grown oxides. The two different groups have received different combinations of pre- and post-processing steps prior to measurements. As expected, low pressure CVD (LPCVD) and thermally grown SiO 2 without any post oxidation annealing (POA) showed significantly different electrical characteristics compared to the wafers that did get a POA. This difference could clearly be distinguished by CnCV, meaning that individual process steps can be analyzed without the fabrication of any test structures on the wafers. As the individual process steps can be analyzed, the uniformity of the individual steps can be accessed. Using a 21-point pattern it was possible to show that there is a non-uniformity in the LPCVD process used prior to the POA. This makes the CnCV technique suitable for in-line characterization and process monitoring.
- 19 May 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1191, 29-35
Open AccessEvaluation of Oxide Processing Steps in SiC Technology Using Contactless Corona-Based CV Measurements
An area of increasing interest for SiC device processing is the processing and qualification of silicon oxides. In this article a contactless corona CV (CnCV) measurement procedure is evaluated as a way to gain more knowledge about the different processes related to oxides. A 21-point measurement pattern is used to gain information about uniformity of oxide properties. Two different types of oxides have been considered, low pressure chemical vapor deposited (CVD) oxides using tetraethylorthosilicate (TEOS) and thermally grown oxides. The two different groups have received different combinations of pre- and post-processing steps prior to measurements. As expected, low pressure CVD (LPCVD) and thermally grown SiO 2 without any post oxidation annealing (POA) showed significantly different electrical characteristics compared to the wafers that did get a POA. This difference could clearly be distinguished by CnCV, meaning that individual process steps can be analyzed without the fabrication of any test structures on the wafers. As the individual process steps can be analyzed, the uniformity of the individual steps can be accessed. Using a 21-point pattern it was possible to show that there is a non-uniformity in the LPCVD process used prior to the POA. This makes the CnCV technique suitable for in-line characterization and process monitoring.