SHShyh- Shin Hwang

Shyh- Shin Hwang

*This is an algorithmically generated author record based on publicly available information.

Shyh- Shin Hwang has a total of 9 co-authors. Here are the top co-authors by number of shared publications:

  • Jui‐Ming Yeh

    Department of Chemistry and Center for Nanotechnology at CYCU, Chung-Yuan Christian University, Chung-Li, Taiwan 32023, Republic of China

    1 shared publication
  • Kung‐Chin Chang

    Department of Chemistry and Center for Nanotechnology at CYCU, Chung-Yuan Christian University, Chung-Li, Taiwan 32023, Republic of China

    1 shared publication
  • Ming-Hsiu Chung

    R&D Centre for Membrane Technology, Chung Yuan University, Chung-Li 320, Taiwan, R.O.C.; fax: + 886-3-265-4388

    1 shared publication
  • Pe-Ming Hsu

    Department of Computer Application Engineering, Far East University, Tainan 774, Taiwan, R.O.C.; fax: +886-6-5977912

    1 shared publication
  • Peming P. Hsu

    Department of Mechanical Engineering, Far-East University, Tainan, Taiwan 74420, Republic of China

    1 shared publication
  • Ping-Shun Hsu

    R&D Centre for Membrane Technology, Chung Yuan University, Chung-Li 320, Taiwan, R.O.C.; fax: + 886-3-265-4388

    1 shared publication

Latest Publications

  • Open Access

    Rheological characterization of polystyrene melts dissolved with supercritical nitrogen fluid during microcellular injection moulding

    by Shia-Chung Chen, Ming-Hsiu Chung, Yu-Wan Lin, Ping-Shun Hsu, Shyh- Shin Hwang, Pe-Ming Hsu

    There are several benefits of using the supercritical fluid microcellular injection moulding process. The part weight, melt temperature, viscosity, moulding pressure, shrink/warpage, and cooling/cycle time are all significantly reduced. The purpose of this study is to investigate the rheological behaviour of PS melt dissolved SCF of nitrogen during Microcellular Injection Moulding process applied with Gas Counter Pressure (GCP) technology. The application of gas into the mould cavity prior to the melt filling provides a counter force against the melt front advancement, restricting the foaming process during the melt filling stage. A slit cavity is designed to measure the pressure drop of polystyrene mixed with 0.4wt% supercritical nitrogen fluid under different mould temperatures (185°C, 195°C, and 205°C), injection speeds (5, 10, and 15 mm/s) as well as counter pressures (0, 150, 300 bars). It was found that melt viscosity is reduced by up to 30% when GCP is increased from 50 to 150 bar as compared to conventional injection moulding. The non-nucleation mixture melt obtained by using a GCP of 300 bar has 32~49% lower viscosity. In addition, the glass transition temperature, T g , was found to be reduced from 96 °C to 50 °C when the applied GCP is 300 bar.


  • The mechanical/thermal properties of microcellular injection‐molded poly‐lactic‐acid nanocomposites

    by Shyh‐Shin Hwang, Peming P. Hsu, Jui‐Ming Yeh, Kung‐Chin Chang, Ying‐Zhong Lai

    This study investigated the influence of montmorillonite (MMT) content on the mechanical/thermal properties of microcellular injection‐molded polylactide (PLA)/clay nanocomposites. Carbon dioxide was the blowing agent. The PLA/MMT nanocomposites were prepared by twin screw extrusion. The results showed that as MMT content is increased, tensile strength, impact strength, and cell density decrease. This is caused by the speed degradation of PLA due to the addition of MMT. MMT decreases the crystallization temperature but increases the decomposition temperature of the nanocomposites. The XRD results showed that the layer spacing of the clay increases as MMT content increases. TEM pictures showed that the MMT is well dispersed within the PLA matrix. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers.