Takashi Yamamoto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Takashi Yamamoto has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Yukio Noma
National Institute for Environmental Studies
7 shared publications- Shin-Ichi Sakai
Environment Preservation Research Center, Kyoto University
6 shared publications Akio Yasuhara
National Institute for Environmental Studies
4 shared publicationsAtsushi Terazono
National Institute for Environmental Studies, Ibaraki, Japan
4 shared publicationsAkiko Kida
Department of Agriculture, Ehime University
3 shared publicationsToshiyuki Toyoguchi
Environmental Control Center Co., Ltd, Tokyo, Japan
3 shared publications
Latest Publications
- Open Access
- 25 June 2025
- Published by Frontiers Media SA in Frontiers in Analytical Science
- Vol. 5, 1571840
Development of a rapid fiber-detection system using artificial intelligence in phase-contrast microscope images of actual atmospheric samples
In this study, we attempted to detect fibers in phase contrast microscope images of actual atmospheric samples using an automatic fiber detection system based on artificial intelligence (AI) models and image processing. In order to detect and correct the release of asbestos fibers due to improper demolition and removal operations of asbestos-containing building materials as early as possible, it is essential to develop a method that can rapidly and accurately measure airborne asbestos fibers. Current rapid measurement method is the combination short-term atmospheric sampling with counting using a phase contrast microscope. However, visual fiber counting takes a reasonable amount of time and is not sufficiently rapid. Additionally, since the counting process relies on visual fiber counting, analytical accuracy can be decreased due to factors such as analyst fatigue. Ambient air samples or air samples collected near demolition sites were observed and acquired using a phase contrast microscope. From the acquired microscopic images and the fiber counting results by the expert analysts, we created a set of 98 training datasets. The Segformer, one of the semantic segmentation models that had achieved good accuracy in previous studies, was adopted as an AI model for automatic fiber detection system. Of the 98 training datasets, 77 datasets were used for training the model, and 21 datasets were used to evaluate the accuracy of the automatic fiber detection system. The achieved detection accuracy by the AI model was 0.90 for recall, 0.68 for precision, and 0.77 for F1 score. Fiber counting accuracy using an automatic fiber detection system based on AI models and image processing was 0.78 for recall, 0.67 for precision, and 0.72 for F1 score. The time required to detect fibers was about one second per image using a graphics processing unit. The counting accuracy by this automatic fiber detection system based on AI model is comparable to that of manual counting by a skilled analyst, yet the time required for fiber counting is 12–50 times faster, significantly reducing the time required for analysis.
- 25 June 2025
- Published by Frontiers Media SA in Frontiers in Analytical Science
- Vol. 5, 1571840
Open AccessDevelopment of a rapid fiber-detection system using artificial intelligence in phase-contrast microscope images of actual atmospheric samples
In this study, we attempted to detect fibers in phase contrast microscope images of actual atmospheric samples using an automatic fiber detection system based on artificial intelligence (AI) models and image processing. In order to detect and correct the release of asbestos fibers due to improper demolition and removal operations of asbestos-containing building materials as early as possible, it is essential to develop a method that can rapidly and accurately measure airborne asbestos fibers. Current rapid measurement method is the combination short-term atmospheric sampling with counting using a phase contrast microscope. However, visual fiber counting takes a reasonable amount of time and is not sufficiently rapid. Additionally, since the counting process relies on visual fiber counting, analytical accuracy can be decreased due to factors such as analyst fatigue. Ambient air samples or air samples collected near demolition sites were observed and acquired using a phase contrast microscope. From the acquired microscopic images and the fiber counting results by the expert analysts, we created a set of 98 training datasets. The Segformer, one of the semantic segmentation models that had achieved good accuracy in previous studies, was adopted as an AI model for automatic fiber detection system. Of the 98 training datasets, 77 datasets were used for training the model, and 21 datasets were used to evaluate the accuracy of the automatic fiber detection system. The achieved detection accuracy by the AI model was 0.90 for recall, 0.68 for precision, and 0.77 for F1 score. Fiber counting accuracy using an automatic fiber detection system based on AI models and image processing was 0.78 for recall, 0.67 for precision, and 0.72 for F1 score. The time required to detect fibers was about one second per image using a graphics processing unit. The counting accuracy by this automatic fiber detection system based on AI model is comparable to that of manual counting by a skilled analyst, yet the time required for fiber counting is 12–50 times faster, significantly reducing the time required for analysis.
- Open Access
- 4 March 2024
- Published by Oxford University Press (OUP) in Annals of Work Exposures and Health
- Vol. 68 (4) , 420-426
Rapid fiber-detection technique by artificial intelligence in phase-contrast microscope images of simulated atmospheric samples
Since the manufacture, import, and use of asbestos products have been completely abolished in Japan, the main cause of asbestos emissions into the atmosphere is the demolition and removal of buildings built with asbestos-containing materials. To detect and correct asbestos emissions from inappropriate demolition and removal operations at an early stage, a rapid method to measure atmospheric asbestos fibers is required. The current rapid measurement method is a combination of short-term atmospheric sampling and phase-contrast microscopy counting. However, visual counting takes a considerable amount of time and is not sufficiently fast. Using artificial intelligence (AI) to analyze microscope images to detect fibers may greatly reduce the time required for counting. Therefore, in this study, we investigated the use of AI image analysis for detecting fibers in phase-contrast microscope images. A series of simulated atmospheric samples prepared from standard samples of amosite and chrysotile were observed using a phase-contrast microscope. Images were captured, and training datasets were created from the counting results of expert analysts. We adopted 2 types of AI models—an instance segmentation model, namely the mask region-based convolutional neural network (Mask R-CNN), and a semantic segmentation model, namely the multi-level aggregation network (MA-Net)—that were trained to detect asbestos fibers. The accuracy of fiber detection achieved with the Mask R-CNN model was 57% for recall and 46% for precision, whereas the accuracy achieved with the MA-Net model was 95% for recall and 91% for precision. Therefore, satisfactory results were obtained with the MA-Net model. The time required for fiber detection was less than 1 s per image in both AI models, which was faster than the time required for counting by an expert analyst.
- 4 March 2024
- Published by Oxford University Press (OUP) in Annals of Work Exposures and Health
- Vol. 68 (4) , 420-426
Open AccessRapid fiber-detection technique by artificial intelligence in phase-contrast microscope images of simulated atmospheric samples
Since the manufacture, import, and use of asbestos products have been completely abolished in Japan, the main cause of asbestos emissions into the atmosphere is the demolition and removal of buildings built with asbestos-containing materials. To detect and correct asbestos emissions from inappropriate demolition and removal operations at an early stage, a rapid method to measure atmospheric asbestos fibers is required. The current rapid measurement method is a combination of short-term atmospheric sampling and phase-contrast microscopy counting. However, visual counting takes a considerable amount of time and is not sufficiently fast. Using artificial intelligence (AI) to analyze microscope images to detect fibers may greatly reduce the time required for counting. Therefore, in this study, we investigated the use of AI image analysis for detecting fibers in phase-contrast microscope images. A series of simulated atmospheric samples prepared from standard samples of amosite and chrysotile were observed using a phase-contrast microscope. Images were captured, and training datasets were created from the counting results of expert analysts. We adopted 2 types of AI models—an instance segmentation model, namely the mask region-based convolutional neural network (Mask R-CNN), and a semantic segmentation model, namely the multi-level aggregation network (MA-Net)—that were trained to detect asbestos fibers. The accuracy of fiber detection achieved with the Mask R-CNN model was 57% for recall and 46% for precision, whereas the accuracy achieved with the MA-Net model was 95% for recall and 91% for precision. Therefore, satisfactory results were obtained with the MA-Net model. The time required for fiber detection was less than 1 s per image in both AI models, which was faster than the time required for counting by an expert analyst.
- Open Access
- 5 April 2018
- Published by Japan Society for Analytical Chemistry in BUNSEKI KAGAKU
- Vol. 67 (4) , 207-212
Study on Rapid Screening Methods for Asbestos in Disaster Debris
Rapid screening methods for asbestos in disaster debris by polarized light microscopy (PLM) and near-infrared spectrometry (NIR) were investigated. In PLM method, disaster debris samples were initially observed with a stereomicroscope to find any fibrous materials. If fibrous materials were found, they were observed by PLM to identify whether they were asbestos or not. The validity of these PLM and NIR methods was confirmed by a field test performed at a disaster waste depot site. Thirty-two debris samples were collected and analyzed by PLM and NIR methods. The screening results were evaluated by comparing the results obtained by a conventional old JIS method. It was confirmed that these rapid screening methods were sufficiently reliable for the on-site screening of asbestos because they presented high correct answer rates (94 % for PLM and 88 % for NIR). Though these methods sometimes reported false negatives for samples of which asbestos concentrations were below 3 %, they can be used for on-site screening because almost all building materials contain asbestos of more than 5 %. The screening periods per sample were about 15 minute for PLM method and about 1 minute for NIR method. Both PLM and NIR methods can be used for on-site rapid screening for asbestos in disaster debris or damaged buildings.
- 5 April 2018
- Published by Japan Society for Analytical Chemistry in BUNSEKI KAGAKU
- Vol. 67 (4) , 207-212
Open AccessStudy on Rapid Screening Methods for Asbestos in Disaster Debris
Rapid screening methods for asbestos in disaster debris by polarized light microscopy (PLM) and near-infrared spectrometry (NIR) were investigated. In PLM method, disaster debris samples were initially observed with a stereomicroscope to find any fibrous materials. If fibrous materials were found, they were observed by PLM to identify whether they were asbestos or not. The validity of these PLM and NIR methods was confirmed by a field test performed at a disaster waste depot site. Thirty-two debris samples were collected and analyzed by PLM and NIR methods. The screening results were evaluated by comparing the results obtained by a conventional old JIS method. It was confirmed that these rapid screening methods were sufficiently reliable for the on-site screening of asbestos because they presented high correct answer rates (94 % for PLM and 88 % for NIR). Though these methods sometimes reported false negatives for samples of which asbestos concentrations were below 3 %, they can be used for on-site screening because almost all building materials contain asbestos of more than 5 %. The screening periods per sample were about 15 minute for PLM method and about 1 minute for NIR method. Both PLM and NIR methods can be used for on-site rapid screening for asbestos in disaster debris or damaged buildings.
- 30 November 2016
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 20 (1) , 214-222
Evaluation of thermally treated asbestos based on fiber number concentration determined by transmission electron microscopy
- 30 November 2016
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 20 (1) , 214-222
Evaluation of thermally treated asbestos based on fiber number concentration determined by transmission electron microscopy
- 2 July 2016
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 25 (32) , 31819-31827
Thermal destruction of wastes containing polychlorinated naphthalenes in an industrial waste incinerator
A series of verification tests were carried out in order to confirm that polychlorinated naphthalenes (PCNs) contained in synthetic rubber products (Neoprene FB products) and aerosol adhesives, which were accidentally imported into Japan, could be thermally destroyed using an industrial waste incinerator. In the verification tests, Neoprene FB products containing PCNs at a concentration of 2800 mg/kg were added to industrial wastes at a ratio of 600 mg Neoprene FB product/kg-waste, and then incinerated at an average temperature of 985 °C. Total PCN concentrations were 14 ng/m3N in stack gas, 5.7 ng/g in bottom ash, 0.98 ng/g in boiler dust, and 1.2 ng/g in fly ash. Destruction efficiency (DE) and destruction removal efficiency (DRE) of congener No. 38/40, which is considered an input marker congener, were 99.9974 and 99.9995 %, respectively. The following dioxin concentrations were found: 0.11 ng-TEQ/m3N for the stack gas, 0.096 ng-TEQ/g for the bottom ash, 0.010 ng-TEQ/g for the boiler dust, and 0.072 ng-TEQ/g for the fly ash. Since the PCN levels in the PCN destruction test were even at slightly lower concentrations than in the baseline test without PCN addition, the detected PCNs are to a large degree unintentionally produced PCNs and does not mainly stem from input material. Also, the dioxin levels did not change. From these results, we confirmed that PCNs contained in Neoprene FB products and aerosol adhesives could be destroyed to a high degree by high-temperature incineration. Therefore, all recalled Neoprene FB products and aerosol adhesives containing PCNs were successfully treated under the same conditions as the verification tests.
- 2 July 2016
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 25 (32) , 31819-31827
Thermal destruction of wastes containing polychlorinated naphthalenes in an industrial waste incinerator
A series of verification tests were carried out in order to confirm that polychlorinated naphthalenes (PCNs) contained in synthetic rubber products (Neoprene FB products) and aerosol adhesives, which were accidentally imported into Japan, could be thermally destroyed using an industrial waste incinerator. In the verification tests, Neoprene FB products containing PCNs at a concentration of 2800 mg/kg were added to industrial wastes at a ratio of 600 mg Neoprene FB product/kg-waste, and then incinerated at an average temperature of 985 °C. Total PCN concentrations were 14 ng/m3N in stack gas, 5.7 ng/g in bottom ash, 0.98 ng/g in boiler dust, and 1.2 ng/g in fly ash. Destruction efficiency (DE) and destruction removal efficiency (DRE) of congener No. 38/40, which is considered an input marker congener, were 99.9974 and 99.9995 %, respectively. The following dioxin concentrations were found: 0.11 ng-TEQ/m3N for the stack gas, 0.096 ng-TEQ/g for the bottom ash, 0.010 ng-TEQ/g for the boiler dust, and 0.072 ng-TEQ/g for the fly ash. Since the PCN levels in the PCN destruction test were even at slightly lower concentrations than in the baseline test without PCN addition, the detected PCNs are to a large degree unintentionally produced PCNs and does not mainly stem from input material. Also, the dioxin levels did not change. From these results, we confirmed that PCNs contained in Neoprene FB products and aerosol adhesives could be destroyed to a high degree by high-temperature incineration. Therefore, all recalled Neoprene FB products and aerosol adhesives containing PCNs were successfully treated under the same conditions as the verification tests.
- 6 March 2014
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 21 (12) , 7557-7566
Destruction of polychlorinated naphthalenes by a high-temperature melting treatment (GeoMelt process)
A series of treatment experiments were carried out to evaluate the applicability of a high-temperature melting treatment (GeoMelt process) to the destruction of polychlorinated naphthalene (PCN) formulation. We started with 10-kg-scale experiments in which a small melting furnace was used and then scaled up to a 1-t-scale experiment in which a melting furnace that resembled an actual treatment system was used. These runs were evaluated whether destruction efficiency (DE) of total PCNs was more than 99.999 % and whether concentrations of PCNs and polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDDs/DFs) in vitrified materials, emission gas, and scrubber water were below the target levels. Because DE values and the target levels of PCNs and PCDDs/DFs in these runs were satisfactory, then we carried out a demonstrative experiment using the actual treatment system and confirmed destruction of PCNs. Based on good results of the demonstrative experiment, stock of PCN formulation was successfully treated continuously.
- 6 March 2014
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 21 (12) , 7557-7566
Destruction of polychlorinated naphthalenes by a high-temperature melting treatment (GeoMelt process)
A series of treatment experiments were carried out to evaluate the applicability of a high-temperature melting treatment (GeoMelt process) to the destruction of polychlorinated naphthalene (PCN) formulation. We started with 10-kg-scale experiments in which a small melting furnace was used and then scaled up to a 1-t-scale experiment in which a melting furnace that resembled an actual treatment system was used. These runs were evaluated whether destruction efficiency (DE) of total PCNs was more than 99.999 % and whether concentrations of PCNs and polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDDs/DFs) in vitrified materials, emission gas, and scrubber water were below the target levels. Because DE values and the target levels of PCNs and PCDDs/DFs in these runs were satisfactory, then we carried out a demonstrative experiment using the actual treatment system and confirmed destruction of PCNs. Based on good results of the demonstrative experiment, stock of PCN formulation was successfully treated continuously.
- 1 February 2014
- Published by Elsevier in Waste Management
- Vol. 34 (2) , 536-541
Development of a testing method for asbestos fibers in treated materials of asbestos containing wastes by transmission electron microscopy
- 1 February 2014
- Published by Elsevier in Waste Management
- Vol. 34 (2) , 536-541
Development of a testing method for asbestos fibers in treated materials of asbestos containing wastes by transmission electron microscopy
- 26 September 2007
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 9 (2) , 188-193
Photodegradation of tetraphenyltin contained in polychlorinated biphenyl-based transformer oil simulants in alkaline 2-propanol solution
- 26 September 2007
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 9 (2) , 188-193
Photodegradation of tetraphenyltin contained in polychlorinated biphenyl-based transformer oil simulants in alkaline 2-propanol solution
- 7 July 2007
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 41 (16) , 5660-5665
Photodegradation of Perfluorooctane Sulfonate by UV Irradiation in Water and Alkaline 2-Propanol
Perfluorooctane sulfonate (PFOS) is the environmentally concerned compound because of its persistence and bioaccumulative properties. Since photodegradation of PFOS is not yet experimentally confirmed, photodegradation study of PFOS in water and alkaline 2-propanol solution was conducted. Aqueous and alkaline 2-propanol solution of PFOS (40 μM) was irradiated with a low-pressure mercury lamp (254 nm, 32 W) by internal irradiation for 10 d, and then PFOS, fluoride and sulfate ions, and the other degradation products were analyzed. Photodegradation of PFOS was confirmed in both media. PFOS was degraded by 8% after 1 day and by 68% after 10 days irradiation compared to the initial concentration in water. In alkaline 2-propanol, 76 and 92% of PFOS was degraded after 1 and 10 days irradiation, respectively. Photodegradation of PFOS in alkaline 2-propanol was much faster and effective than in water, as the photodegradation rate constants were 0.93 days-1 in alkaline 2-propanol and 0.13 days-1 in water, respectively. Formation of fluoride and sulfate was also confirmed by ion chromatography and X-ray diffraction analysis. From observation of the degradation products, two major degradation pathways of PFOS were considered: via C8HF17 and C8F17OH, respectively, resulting in short-chain fluorinated compounds such as C7HF15 and C7F15OH by stepwise removal of CF2. Formation of short-chain fluorocarbons such as CF4, C2F6, and C3F8 were also confirmed. This is the first study to confirm photodegradation of PFOS in water and alkaline 2-propanol.
- 7 July 2007
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 41 (16) , 5660-5665
Photodegradation of Perfluorooctane Sulfonate by UV Irradiation in Water and Alkaline 2-Propanol
Perfluorooctane sulfonate (PFOS) is the environmentally concerned compound because of its persistence and bioaccumulative properties. Since photodegradation of PFOS is not yet experimentally confirmed, photodegradation study of PFOS in water and alkaline 2-propanol solution was conducted. Aqueous and alkaline 2-propanol solution of PFOS (40 μM) was irradiated with a low-pressure mercury lamp (254 nm, 32 W) by internal irradiation for 10 d, and then PFOS, fluoride and sulfate ions, and the other degradation products were analyzed. Photodegradation of PFOS was confirmed in both media. PFOS was degraded by 8% after 1 day and by 68% after 10 days irradiation compared to the initial concentration in water. In alkaline 2-propanol, 76 and 92% of PFOS was degraded after 1 and 10 days irradiation, respectively. Photodegradation of PFOS in alkaline 2-propanol was much faster and effective than in water, as the photodegradation rate constants were 0.93 days-1 in alkaline 2-propanol and 0.13 days-1 in water, respectively. Formation of fluoride and sulfate was also confirmed by ion chromatography and X-ray diffraction analysis. From observation of the degradation products, two major degradation pathways of PFOS were considered: via C8HF17 and C8F17OH, respectively, resulting in short-chain fluorinated compounds such as C7HF15 and C7F15OH by stepwise removal of CF2. Formation of short-chain fluorocarbons such as CF4, C2F6, and C3F8 were also confirmed. This is the first study to confirm photodegradation of PFOS in water and alkaline 2-propanol.
- 17 September 2003
- Published by Elsevier in Journal of Chromatography A
- Vol. 1017 (1) , 195-206
Analytical methods for phenyltin compounds in polychlorinated biphenyl-based transformer oil samples.
- 17 September 2003
- Published by Elsevier in Journal of Chromatography A
- Vol. 1017 (1) , 195-206
Analytical methods for phenyltin compounds in polychlorinated biphenyl-based transformer oil samples.