In-Shup Ahn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
In-Shup Ahn has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
Dong-Kyu Park
6 shared publicationsSung-Hyun Choi
Gyeongsang National University
3 shared publicationsDeuk Kyun Kang
School of nano and advanced Materials Engineering, I-Cube Center, K-MEM R&D cluster, ReCAPT, Gyeongsang National University, Gyeongnam, Korea
2 shared publicationsDong Woong Kim
School of nano and advanced Materials Engineering, I-Cube Center, K-MEM R&D cluster, ReCAPT, Gyeongsang National University, Gyeongnam, Korea
2 shared publicationsDong-Wook Park
Gyeongsang National University
2 shared publicationsJin-Uk Ok
Gyeongsang Natl Univ, Sch Nano & Adv Mat Sci & Engn, 900 Gajwa Dong, Jinju 660701, Gyeongnam, South Korea
2 shared publications
Latest Publications
- 30 April 2019
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 26 (2) , 107-111
Prediction the Phase Transformation Time of Binary Alloy System by calculating the Input Energy of Mechanical Alloying
- 30 April 2019
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 26 (2) , 107-111
Prediction the Phase Transformation Time of Binary Alloy System by calculating the Input Energy of Mechanical Alloying
- 30 April 2019
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 26 (2) , 112-118
Thermal Properties and Microstructural Changes of Fe-Co System Valve Seat Alloy by High Densification Process
- 30 April 2019
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 26 (2) , 112-118
Thermal Properties and Microstructural Changes of Fe-Co System Valve Seat Alloy by High Densification Process
- 1 September 2018
- Published by American Scientific Publishers in Science of Advanced Materials
- Vol. 10 (9) , 1356-1361
Mechanical Properties of Fe–P–(Mo, Mn) Sintered Alloy Designed with Si Added Lean Alloy Powder Composition
A lean alloy is defined as a low alloy steel that minimizes the content of the alloying elements while maintaining the characteristics of the sintered alloy. The purpose of this study is to determine the change in mechanical properties with the addition of silicon in Fe–P–Mo, Fe–P–Mn, and Fe–P–Mo–Mn alloys. Silicon-added Fe–P–Mo, Fe–P–Mn, and Fe–P–Mo–Mn master alloys were compacted at 7.0 g/cm3 and then sintered under a H2–N2 atmosphere at 1120 °C. The sintered density of three alloy systems having the same green density (7.0 g/cm3) decreased owing to dimensional expansion with an increasing Si content. As the diffusion rate in the Fe–P–Mo system is faster than that in the Fe–P–Mn system, the decrease in the sintered density was largest in the Fe–P–Mn system. The transverse rupture strengths (TRS) of the Fe–P–Mo and Fe–P–Mo–Mn systems were constant as the Si content increased. However, the TRS slope of the Fe–P–Mn changed at 0.4 wt% Si; this is caused by phase change, where the α + γ phase was transformed into a full α phase for Si contents higher than 0.4 wt%.
- 1 September 2018
- Published by American Scientific Publishers in Science of Advanced Materials
- Vol. 10 (9) , 1356-1361
Mechanical Properties of Fe–P–(Mo, Mn) Sintered Alloy Designed with Si Added Lean Alloy Powder Composition
A lean alloy is defined as a low alloy steel that minimizes the content of the alloying elements while maintaining the characteristics of the sintered alloy. The purpose of this study is to determine the change in mechanical properties with the addition of silicon in Fe–P–Mo, Fe–P–Mn, and Fe–P–Mo–Mn alloys. Silicon-added Fe–P–Mo, Fe–P–Mn, and Fe–P–Mo–Mn master alloys were compacted at 7.0 g/cm3 and then sintered under a H2–N2 atmosphere at 1120 °C. The sintered density of three alloy systems having the same green density (7.0 g/cm3) decreased owing to dimensional expansion with an increasing Si content. As the diffusion rate in the Fe–P–Mo system is faster than that in the Fe–P–Mn system, the decrease in the sintered density was largest in the Fe–P–Mn system. The transverse rupture strengths (TRS) of the Fe–P–Mo and Fe–P–Mo–Mn systems were constant as the Si content increased. However, the TRS slope of the Fe–P–Mn changed at 0.4 wt% Si; this is caused by phase change, where the α + γ phase was transformed into a full α phase for Si contents higher than 0.4 wt%.
- 31 August 2017
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 24 (4) , 292-297
The Effect of SiO2 addition on Oxidation and Electrical Resistance Stability at High-temperature of P/M Fecralloy Compact
- 31 August 2017
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 24 (4) , 292-297
The Effect of SiO2 addition on Oxidation and Electrical Resistance Stability at High-temperature of P/M Fecralloy Compact
- 16 May 2014
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 40 (7) , 2415-2421
A study of the debinding and sintering behavior of T42 high-speed steel produced by powder injection molding (PIM)
- 16 May 2014
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 40 (7) , 2415-2421
A study of the debinding and sintering behavior of T42 high-speed steel produced by powder injection molding (PIM)
- 27 December 2011
- Published by Springer Nature in Metals and Materials International
- Vol. 17 (6) , 937-942
Study on the sintering behavior and microstructure development of the powder injection molded T42 high-speed steel
- 27 December 2011
- Published by Springer Nature in Metals and Materials International
- Vol. 17 (6) , 937-942
Study on the sintering behavior and microstructure development of the powder injection molded T42 high-speed steel
- 1 March 2011
- Published by Wiley in Rare Metals
- Vol. 30 (S1) , 5-10
A study of Ni 3 S 2 synthesized by mechanical alloying for Na/Ni 3 S 2 cell
To synthesize nanocrystalline Ni 3 S 2 cathode material for Na/Ni 3 S 2 cell with low cost nickel and sulfur elements, mechanical alloying (MA) was employed directly and with different ball powder ratios (BPRs) of 20: 1, 25: 1 and 30: 1, the mean particle size of 3.99, 2.84 and 2.75 μm can be obtained, respectively. In order to ulteriorly reduce the particle size to improve the contact areas between the active materials, the wet ball milling with the normal Hexane (C 6 H 14 ) as the milling solvent was also conducted for 30 h using the ball milling machine, and the submicro Ni 3 S 2 powder particles can be gained. The charge/discharge properties of Na/Ni 3 S 2 cells for wet milled system were investigated at room temperature using 1 M NaCF 3 SO 3 (sodium trifluoromethanesulfonate) dissolved in TEGDME (tetra ethylene glycol dimethyl ether) as the liquid electrolyte. And the initial charge/discharge capacity was 397 and 425 mAh/g, respectively, which indicates the small particle size of cathode materials are conductive to the discharge properties.
- 1 March 2011
- Published by Wiley in Rare Metals
- Vol. 30 (S1) , 5-10
A study of Ni 3 S 2 synthesized by mechanical alloying for Na/Ni 3 S 2 cell
To synthesize nanocrystalline Ni 3 S 2 cathode material for Na/Ni 3 S 2 cell with low cost nickel and sulfur elements, mechanical alloying (MA) was employed directly and with different ball powder ratios (BPRs) of 20: 1, 25: 1 and 30: 1, the mean particle size of 3.99, 2.84 and 2.75 μm can be obtained, respectively. In order to ulteriorly reduce the particle size to improve the contact areas between the active materials, the wet ball milling with the normal Hexane (C 6 H 14 ) as the milling solvent was also conducted for 30 h using the ball milling machine, and the submicro Ni 3 S 2 powder particles can be gained. The charge/discharge properties of Na/Ni 3 S 2 cells for wet milled system were investigated at room temperature using 1 M NaCF 3 SO 3 (sodium trifluoromethanesulfonate) dissolved in TEGDME (tetra ethylene glycol dimethyl ether) as the liquid electrolyte. And the initial charge/discharge capacity was 397 and 425 mAh/g, respectively, which indicates the small particle size of cathode materials are conductive to the discharge properties.
- 6 October 2010
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 36 (6-7) , 785-793
The Ni3Al–Al2O3/TiC cermet formation behavior with TiH2 base ball-milled powders with Ni, Al, and C during spark plasma sintering
- 6 October 2010
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 36 (6-7) , 785-793
The Ni3Al–Al2O3/TiC cermet formation behavior with TiH2 base ball-milled powders with Ni, Al, and C during spark plasma sintering
- 5 October 2010
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 36 (6-7) , 743-748
The effect of sintering conditions on the properties of WC–10wt%Co PIM compacts
- 5 October 2010
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 36 (6-7) , 743-748
The effect of sintering conditions on the properties of WC–10wt%Co PIM compacts
- 20 February 2009
- Published by Springer Nature in Metals and Materials International
- Vol. 15 (1) , 15-19
Phase formation of MgB2 superconducting materials fabricated by spark plasma sintering
- 20 February 2009
- Published by Springer Nature in Metals and Materials International
- Vol. 15 (1) , 15-19
Phase formation of MgB2 superconducting materials fabricated by spark plasma sintering