Xuda Qin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xuda Qin has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Hao Li
Key Laboratory of Mechanism Theory and Equipment Design of Ministry of Education Tianjin University Tianjin China
17 shared publications - Dan Sun
School of Mechanical & Aerospace Engineering, Queen’s University Belfast, Belfast, UK
5 shared publications - Shipeng Li
Key Laboratory of Mechanism Theory and Equipment Design of Ministry of Education Tianjin University Tianjin China
4 shared publications Yan Jin
Queens University
4 shared publicationsGaiyun He
Key Laboratory of Mechanism Theory and Equipment Design of Ministry of Education, Tianjin University, Tianjin, China
3 shared publicationsQing Zhao
Key Laboratory of Mechanism Theory and Equipment Design of Ministry of Education, Tianjin University, Tianjin, China
3 shared publications
Latest Publications
- 4 July 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 139 (5-6) , 2123-2138
Study on drilling and interfacial damage formation mechanisms of CF/PPS-Al induction welded laminates via experimental and numerical method
- 4 July 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 139 (5-6) , 2123-2138
Study on drilling and interfacial damage formation mechanisms of CF/PPS-Al induction welded laminates via experimental and numerical method
- 18 August 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 122 (2) , 1083-1097
Surface quality evaluation for CFRP milling and its impact on the mechanical properties
- 18 August 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 122 (2) , 1083-1097
Surface quality evaluation for CFRP milling and its impact on the mechanical properties
- Open Access
Analysis of 3-DOF Cutting Stability of Titanium Alloy Helical Milling Based on PKM and Machining Quality Optimization
Aiming at the requirements of titanium alloy holes in aircraft industry, the 3-DOF cutting stability and surface quality optimization of parallel kinematic manipulator (PKM) are studied. The variation of natural frequencies with the end-effector position of the PKM is analyzed. The cutting force model of titanium alloy helical milling based PKM is developed, and the cutting force coefficients are identified. The prediction model for 3-DOF the stability of helical milling based on the PKM is established through a Semi-Discrete method, and the stability lobes are obtained. The correctness of the stability lobes is verified by subjecting the cutting force signal to time-frequency transformation and roughness detection. The step-cutter is used for machining process improvement to enhance the stability domain. The method proposed in this paper can provide a reference for further optimization of the prediction and optimization of the milling process of difficult-to-process materials based on PKM in the future.
Open AccessAnalysis of 3-DOF Cutting Stability of Titanium Alloy Helical Milling Based on PKM and Machining Quality Optimization
Aiming at the requirements of titanium alloy holes in aircraft industry, the 3-DOF cutting stability and surface quality optimization of parallel kinematic manipulator (PKM) are studied. The variation of natural frequencies with the end-effector position of the PKM is analyzed. The cutting force model of titanium alloy helical milling based PKM is developed, and the cutting force coefficients are identified. The prediction model for 3-DOF the stability of helical milling based on the PKM is established through a Semi-Discrete method, and the stability lobes are obtained. The correctness of the stability lobes is verified by subjecting the cutting force signal to time-frequency transformation and roughness detection. The step-cutter is used for machining process improvement to enhance the stability domain. The method proposed in this paper can provide a reference for further optimization of the prediction and optimization of the milling process of difficult-to-process materials based on PKM in the future.
- 16 January 2022
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 99 (4) , 584-605
Influence of high pulse fluence infrared laser surface pretreatment parameters on the mechanical properties of CFRP/aluminium alloy adhesive joints
Laser surface pretreatment is an effective approach for improving the mechanical properties of adhesive joints. In the case of laser surface treatment of carbon fibre reinforced polymer (CFRP), ultraviolet (UV) lasers and lower pulse fluence infrared (IR) lasers are usually used to ensure the surface pretreatment quality. With respect to improving the surface treatment efficiency as much as possible, the influence of higher pulse fluence (12.7 J/cm2) IR laser pretreatment parameters on the mechanical properties of CFRP/aluminium alloy hybrid joints were investigated in this study. Scanning electron microscopy (SEM), contact angle measurements, confocal laser scanning microscope (CLSM), and X-ray photoelectron spectroscopy (XPS) were used to analyse the surface modification and failure modes of the adhesive surface. Additionally, the influence of the IR laser pretreatment parameters on the failure mode of CFRP/aluminium alloy adhesive joints under tension loading was discussed. The results showed that in addition to surface free energy, subsurface damage and mechanical interlocking were important factors affecting the shear strength of CFRP/aluminium alloy adhesive joints when a higher pulse fluence IR laser was applied for surface pretreatment. Finally, the optimized laser surface pretreatment parameters considering both the treatment efficiency and quality were obtained for the CFRP/aluminium alloy adhesive joint.
- 16 January 2022
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 99 (4) , 584-605
Influence of high pulse fluence infrared laser surface pretreatment parameters on the mechanical properties of CFRP/aluminium alloy adhesive joints
Laser surface pretreatment is an effective approach for improving the mechanical properties of adhesive joints. In the case of laser surface treatment of carbon fibre reinforced polymer (CFRP), ultraviolet (UV) lasers and lower pulse fluence infrared (IR) lasers are usually used to ensure the surface pretreatment quality. With respect to improving the surface treatment efficiency as much as possible, the influence of higher pulse fluence (12.7 J/cm2) IR laser pretreatment parameters on the mechanical properties of CFRP/aluminium alloy hybrid joints were investigated in this study. Scanning electron microscopy (SEM), contact angle measurements, confocal laser scanning microscope (CLSM), and X-ray photoelectron spectroscopy (XPS) were used to analyse the surface modification and failure modes of the adhesive surface. Additionally, the influence of the IR laser pretreatment parameters on the failure mode of CFRP/aluminium alloy adhesive joints under tension loading was discussed. The results showed that in addition to surface free energy, subsurface damage and mechanical interlocking were important factors affecting the shear strength of CFRP/aluminium alloy adhesive joints when a higher pulse fluence IR laser was applied for surface pretreatment. Finally, the optimized laser surface pretreatment parameters considering both the treatment efficiency and quality were obtained for the CFRP/aluminium alloy adhesive joint.
- 12 November 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 119 (1-2) , 1003-1017
Numerical and experimental investigation of orthogonal cutting of carbon fiber-reinforced polyetheretherketone (CF/PEEK)
- 12 November 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 119 (1-2) , 1003-1017
Numerical and experimental investigation of orthogonal cutting of carbon fiber-reinforced polyetheretherketone (CF/PEEK)
- 1 January 2021
- Published by Japan Society of Mechanical Engineers in Journal of Advanced Mechanical Design, Systems, and Manufacturing
- Vol. 15 (1) , JAMDSM0004
Tribological and dry drilling performance of WS2/Cr-AlCrN coatings
Dry drilling gives a higher request to the anti-friction property of cutting tools. However, most tool coatings commonly have less lubricant effect. In present paper, WS2/Cr layer was deposited on AlCrN layer by a radio frequency magnetron sputtering system, forming the WS2/Cr-AlCrN lubricant-hard coatings. Its microstructure was studied using scanning electric microscope (SEM) and X-ray diffraction (XRD). Dry sliding tests were carried out against Ti6Al4V balls to evaluate the lubricant effect of the lubricant-hard coatings with different Cr contents in WS2/Cr layer. Dry drilling performance of WS2/Cr-AlCrN coating was also studied compared with uncoated and AlCrN coated tool in dry drilling of Ti6Al4V and 7075Al. It is found that as Cr contents increased, WS2/Cr became denser but the crystallinity decreased. The coating with Cr content of ~9.8 at.% had the best lubricant effect with the lowest friction coefficient and the narrowest wear track. Dry drilling tests show that WS2/Cr-AlCrN coated tool had the longest tool life and produced the lowest surface roughness. The high wear resistance of AlCrN layer was mainly played near cutting edge. While the anti-friction role of the lubricant layer was mainly played on drill flute, resulting in less material adhesion and improved chip removal.
- 1 January 2021
- Published by Japan Society of Mechanical Engineers in Journal of Advanced Mechanical Design, Systems, and Manufacturing
- Vol. 15 (1) , JAMDSM0004
Tribological and dry drilling performance of WS2/Cr-AlCrN coatings
Dry drilling gives a higher request to the anti-friction property of cutting tools. However, most tool coatings commonly have less lubricant effect. In present paper, WS2/Cr layer was deposited on AlCrN layer by a radio frequency magnetron sputtering system, forming the WS2/Cr-AlCrN lubricant-hard coatings. Its microstructure was studied using scanning electric microscope (SEM) and X-ray diffraction (XRD). Dry sliding tests were carried out against Ti6Al4V balls to evaluate the lubricant effect of the lubricant-hard coatings with different Cr contents in WS2/Cr layer. Dry drilling performance of WS2/Cr-AlCrN coating was also studied compared with uncoated and AlCrN coated tool in dry drilling of Ti6Al4V and 7075Al. It is found that as Cr contents increased, WS2/Cr became denser but the crystallinity decreased. The coating with Cr content of ~9.8 at.% had the best lubricant effect with the lowest friction coefficient and the narrowest wear track. Dry drilling tests show that WS2/Cr-AlCrN coated tool had the longest tool life and produced the lowest surface roughness. The high wear resistance of AlCrN layer was mainly played near cutting edge. While the anti-friction role of the lubricant layer was mainly played on drill flute, resulting in less material adhesion and improved chip removal.
- 8 November 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 111 (11-12) , 3207-3224
Cutting force and chatter stability analysis for PKM-based helical milling operation
- 8 November 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 111 (11-12) , 3207-3224
Cutting force and chatter stability analysis for PKM-based helical milling operation
- 7 March 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 102 (9-12) , 4199-4211
A bond-based peridynamic modeling of machining of unidirectional carbon fiber reinforced polymer material
- 7 March 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 102 (9-12) , 4199-4211
A bond-based peridynamic modeling of machining of unidirectional carbon fiber reinforced polymer material
- Open Access
- 1 January 2019
- Published by Japan Society of Mechanical Engineers in Journal of Advanced Mechanical Design, Systems, and Manufacturing
- Vol. 13 (2) , JAMDSM0041
Deformation analysis and hole diameter error compensation for hybrid robot based helical milling
As an innovative machining process for hole-making, helical milling (also known as orbital drilling) presents great potential in machining aircraft structures due to temperature and cutting force reduction, flexible kinematics, and improved borehole quality. Meanwhile, the application of hybrid robot with their high accuracy and better stiffness are increased in aircraft assembly machining operations. Combining these two advanced technologies, this paper focuses primarily on the investigation of the TriMule hybrid robot elastic deformation during helical milling hole-making process and its influence on the diameter error of machined hole. The elastic deformation of series and parallel parts under cutting force condition was investigated by finite element simulation software SAMCEF. The TriMule robot helical milling experiments were also carried out to determine the variation of hole diameter error, and an offline compensation method with modifying the eccentricity at different hole depth was proposed based on the established diameter error model. From experimental verification results, it can be found that the hole diameter error of TriMule robot helical milling can be reduced and the consistency of hole diameter accuracy can be significantly improved by proposed error compensation method.
- 1 January 2019
- Published by Japan Society of Mechanical Engineers in Journal of Advanced Mechanical Design, Systems, and Manufacturing
- Vol. 13 (2) , JAMDSM0041
Open AccessDeformation analysis and hole diameter error compensation for hybrid robot based helical milling
As an innovative machining process for hole-making, helical milling (also known as orbital drilling) presents great potential in machining aircraft structures due to temperature and cutting force reduction, flexible kinematics, and improved borehole quality. Meanwhile, the application of hybrid robot with their high accuracy and better stiffness are increased in aircraft assembly machining operations. Combining these two advanced technologies, this paper focuses primarily on the investigation of the TriMule hybrid robot elastic deformation during helical milling hole-making process and its influence on the diameter error of machined hole. The elastic deformation of series and parallel parts under cutting force condition was investigated by finite element simulation software SAMCEF. The TriMule robot helical milling experiments were also carried out to determine the variation of hole diameter error, and an offline compensation method with modifying the eccentricity at different hole depth was proposed based on the established diameter error model. From experimental verification results, it can be found that the hole diameter error of TriMule robot helical milling can be reduced and the consistency of hole diameter accuracy can be significantly improved by proposed error compensation method.