S. Mine
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
S. Mine has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
C. Immer
GE Global Research, OneResearch Circle, Niskayuna NY 12309, USA
1 shared publicationChristopher Immer
GE Global Research Center, Niskayuna, NY, USA
1 shared publicationE.T. Laskaris
GE Global Research, OneResearch Circle, Niskayuna NY 12309, USA
1 shared publicationEvangelos T. Laskaris
GE Global Research Center, Niskayuna, NY, USA
1 shared publicationK. Amm
GE Global Research, OneResearch Circle, Niskayuna NY 12309, USA
1 shared publicationKathleen Amm
GE Global Research Center, Niskayuna, NY, USA
1 shared publication
Latest Publications
- 22 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 25 (3) , 1-4
Development of a 3 T–250 mm Bore $\hbox{MgB}_{2}$ Magnet SystemThe authors had reported components' development of 3 T–250 mm bore $\hbox{MgB}_{2}$ magnet system. Pre-reacted $\hbox{MgB}_{2}$ tape wire with copper lamination had n-value related problem due to raw Boron particle size inequality, but it had been corrected. Long $\hbox{MgB}_{2}$ wires over 3 km had been supplied. All six component coils were made with a wet winding procedure. They were tested individually with the same cooling scheme of conduction cooling as the actual magnet assembly. Though all coils could be ramped to some extent, some coils showed fairly large remnant voltage. Since the voltage distribution over the coil was not even, the uniformity along the wire length may not be good enough. The stability of the coil was verified by its no training performance even with fast ramping. The magnet assembly and its test with conduction cooling were planned. $I_{c}$ of the superconducting joint with this pre-reacted wire was doubled during past one year's development.
- 22 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 25 (3) , 1-4
Development of a 3 T–250 mm Bore $\hbox{MgB}_{2}$ Magnet SystemThe authors had reported components' development of 3 T–250 mm bore $\hbox{MgB}_{2}$ magnet system. Pre-reacted $\hbox{MgB}_{2}$ tape wire with copper lamination had n-value related problem due to raw Boron particle size inequality, but it had been corrected. Long $\hbox{MgB}_{2}$ wires over 3 km had been supplied. All six component coils were made with a wet winding procedure. They were tested individually with the same cooling scheme of conduction cooling as the actual magnet assembly. Though all coils could be ramped to some extent, some coils showed fairly large remnant voltage. Since the voltage distribution over the coil was not even, the uniformity along the wire length may not be good enough. The stability of the coil was verified by its no training performance even with fast ramping. The magnet assembly and its test with conduction cooling were planned. $I_{c}$ of the superconducting joint with this pre-reacted wire was doubled during past one year's development.
- Open Access
- 10 October 2014
- Published by Elsevier in Physics Procedia
- Vol. 58, 224-227
Development of a 3 T-10” Bore MgB2 Magnet at GE
- 10 October 2014
- Published by Elsevier in Physics Procedia
- Vol. 58, 224-227
Open AccessDevelopment of a 3 T-10” Bore MgB2 Magnet at GE