Balaji Gururajan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Balaji Gururajan has a total of 76 co-authors. Here are the top co-authors by number of shared publications:
- Wei-Sheng Liu
Department of Electrical Engineering, Yuan Ze University, Chung-Li Dist., Taoyuan 32003, Taiwan
9 shared publications R. Balasundaraprabhu
PSG Coll Technol, Ctr Surface Sci, Dept Phys, Coimbatore 641004, Tamil Nadu, India
5 shared publicationsN. Prabavathy
PSG Coll Technol, Ctr Surface Sci, Dept Phys, Coimbatore 641004, Tamil Nadu, India
4 shared publications- Venkatesh Narasihman
Department of Electrical Engineering, Yuan Ze University , Chung-Li Dist., Taoyuan 32003
4 shared publications Dhayalan Velauthapillai
Western Norway Univ Appl Sci, Fac Engn & Business Adm, N-5063 Bergen, Norway
3 shared publicationsK. Sivakumaran
PSG Coll Technol, Ctr Surface Sci, Dept Phys, Coimbatore 641004, Tamil Nadu, India
3 shared publications
Latest Publications
- 28 October 2026
- Published by Elsevier in Surfaces and Interfaces
- Vol. 101
Visible-blind deep-UV Photodetection without optical filters: a fully sputtered p-CuAlO2/n-MgZnO all-oxide heterojunction
- 28 October 2026
- Published by Elsevier in Surfaces and Interfaces
- Vol. 101
Visible-blind deep-UV Photodetection without optical filters: a fully sputtered p-CuAlO2/n-MgZnO all-oxide heterojunction
- 27 March 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (3)
Impact of arsenic species on InAs/GaSb type II superlattice grown by molecular beam epitaxy
In this study, InAs/GaSb type-II superlattice (T2SL) structures were grown on GaSb substrates by molecular beam epitaxy to investigate the impact of arsenic species (As2 dimers vs As4 tetramers) and growth temperatures (385–425 °C) on the interface quality and device performance. Structural characterization revealed that InAs layers grown with As4 at 385 °C exhibit superior crystallinity, evidenced by sharper higher-order satellite peaks and minimal lattice strain in high-resolution x-ray diffraction patterns. High-resolution transmission electron microscopy further confirms the abruptness of the interface with suppressed intermixing. Photoluminescence measurements demonstrate enhanced emission intensity and narrower linewidths for samples grown with As4 at 385 °C compared to those grown with As2. The reduced reactivity and sticking coefficient of As4, relative to As2, likely suppress uncontrolled anion exchange, particularly at lower growth temperatures. In contrast, As2 facilitates direct substitutional incorporation, driven by lower activation energy barriers, which promotes aggressive As-Sb exchange at heterointerfaces. This leads to compromised crystal integrity through the formation of parasitic ternary/quaternary phases and an increase in nonradiative defect centers, which adversely affect optical performance. Fabricated p-i-n diodes utilizing the optimized As4-grown T2SL exhibit a low room-temperature dark current density of 2.2 × 10−5 A/cm2, attributed to the suppression of generation-recombination and tunneling currents via enhanced interface quality. These results demonstrate that As4-mediated growth effectively mitigates anion exchange, paving the way for high-operating-temperature T2SL devices in midwave infrared optoelectronics.
- 27 March 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (3)
Impact of arsenic species on InAs/GaSb type II superlattice grown by molecular beam epitaxy
In this study, InAs/GaSb type-II superlattice (T2SL) structures were grown on GaSb substrates by molecular beam epitaxy to investigate the impact of arsenic species (As2 dimers vs As4 tetramers) and growth temperatures (385–425 °C) on the interface quality and device performance. Structural characterization revealed that InAs layers grown with As4 at 385 °C exhibit superior crystallinity, evidenced by sharper higher-order satellite peaks and minimal lattice strain in high-resolution x-ray diffraction patterns. High-resolution transmission electron microscopy further confirms the abruptness of the interface with suppressed intermixing. Photoluminescence measurements demonstrate enhanced emission intensity and narrower linewidths for samples grown with As4 at 385 °C compared to those grown with As2. The reduced reactivity and sticking coefficient of As4, relative to As2, likely suppress uncontrolled anion exchange, particularly at lower growth temperatures. In contrast, As2 facilitates direct substitutional incorporation, driven by lower activation energy barriers, which promotes aggressive As-Sb exchange at heterointerfaces. This leads to compromised crystal integrity through the formation of parasitic ternary/quaternary phases and an increase in nonradiative defect centers, which adversely affect optical performance. Fabricated p-i-n diodes utilizing the optimized As4-grown T2SL exhibit a low room-temperature dark current density of 2.2 × 10−5 A/cm2, attributed to the suppression of generation-recombination and tunneling currents via enhanced interface quality. These results demonstrate that As4-mediated growth effectively mitigates anion exchange, paving the way for high-operating-temperature T2SL devices in midwave infrared optoelectronics.
- Open Access
- 19 November 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (47) , 56883-56912
Copper-Doped Chromium Oxide Delafossite: Sputtering Process, Material Properties, and Device Applications: A Detailed Review
Transparent conducting oxides (TCOs) are essential for modern optoelectronic technologies, providing a perfect combination of great optical transparency and superior electrical conductivity. Although n-type transparent conductive oxides dominate in the field, the advancement of p-type TCOs is crucial for the realization of entirely transparent electrical devices. Delafossite-based Copper-doped chromium oxide (CuCrO2) is a notable p-type TCO, exhibiting significant optical transparency, electrical conductivity, and magnetic adaptability. Its abundant and nontoxic characteristics further augment its attractiveness for sustainable energy and optoelectronic applications. This review examines the fabrication and optimization of sputtered CuCrO2 thin films, highlighting deposition procedures, post-treatment methods, and their effects on structural, morphological, electrical, and optical properties. The material’s excellent sheet conductivity and improved valence band alignment resolve permanent issues in the development of p-type transparent conductive oxides. The applications of CuCrO2 include transparent optoelectronics, light-emitting diodes, thin-film transistors, and solar energy systems. Sputtered CuCrO2 films balance transparency and conductivity, facilitating the development of novel and sustainable devices. This review offers essential insights for guiding future research and practical implementation, positioning CuCrO2 as a fundamental component for next-generation transparent electronics.
- 19 November 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (47) , 56883-56912
Open AccessCopper-Doped Chromium Oxide Delafossite: Sputtering Process, Material Properties, and Device Applications: A Detailed Review
Transparent conducting oxides (TCOs) are essential for modern optoelectronic technologies, providing a perfect combination of great optical transparency and superior electrical conductivity. Although n-type transparent conductive oxides dominate in the field, the advancement of p-type TCOs is crucial for the realization of entirely transparent electrical devices. Delafossite-based Copper-doped chromium oxide (CuCrO2) is a notable p-type TCO, exhibiting significant optical transparency, electrical conductivity, and magnetic adaptability. Its abundant and nontoxic characteristics further augment its attractiveness for sustainable energy and optoelectronic applications. This review examines the fabrication and optimization of sputtered CuCrO2 thin films, highlighting deposition procedures, post-treatment methods, and their effects on structural, morphological, electrical, and optical properties. The material’s excellent sheet conductivity and improved valence band alignment resolve permanent issues in the development of p-type transparent conductive oxides. The applications of CuCrO2 include transparent optoelectronics, light-emitting diodes, thin-film transistors, and solar energy systems. Sputtered CuCrO2 films balance transparency and conductivity, facilitating the development of novel and sustainable devices. This review offers essential insights for guiding future research and practical implementation, positioning CuCrO2 as a fundamental component for next-generation transparent electronics.
- 5 July 2025
- Published by Wiley in Advanced Theory and Simulations
- Vol. 8 (11)
Numerical Investigation of Eco‐Friendly All‐Zinc Based Thin Film Solar Cells For Sustainable Photovoltaics
In this numerical study, the performance of thin‐film solar cells comprising entirely Zn‐based layers is evaluated using SCAPS‐1D. ZnSnN₂ is chosen as the absorber layer due to its abundance on earth, and it has good optoelectrical properties suitable for photovoltaic (PV) applications. Its narrow bandgap and high absorption coefficient further enhance its suitability for such devices. The buffer layers explored in this study include ZnN, ZnON, ZnS, and ZnOS, all containing zinc. Likewise, the window layers examined are AZO, GZO, and ZTO. Nickel and Aluminium are used as the front and back contacts. A comprehensive analysis of each layer's properties and potential defects is conducted to improve the solar cell efficiency. The optimized device structure is determined to be Ni/ZnSnN₂/ZnON/ZTO/Al, achieving an efficiency of ≈19% with a short‐circuit current density (Jsc) of 20.05 mA cm − 2 and an open‐circuit voltage (Voc) of 1.1 V. These findings present a novel, eco‐friendly, scalable, and efficient thin film solar cell design unlike its predecessor fabricated with toxic and rare earth materials.
- 5 July 2025
- Published by Wiley in Advanced Theory and Simulations
- Vol. 8 (11)
Numerical Investigation of Eco‐Friendly All‐Zinc Based Thin Film Solar Cells For Sustainable Photovoltaics
In this numerical study, the performance of thin‐film solar cells comprising entirely Zn‐based layers is evaluated using SCAPS‐1D. ZnSnN₂ is chosen as the absorber layer due to its abundance on earth, and it has good optoelectrical properties suitable for photovoltaic (PV) applications. Its narrow bandgap and high absorption coefficient further enhance its suitability for such devices. The buffer layers explored in this study include ZnN, ZnON, ZnS, and ZnOS, all containing zinc. Likewise, the window layers examined are AZO, GZO, and ZTO. Nickel and Aluminium are used as the front and back contacts. A comprehensive analysis of each layer's properties and potential defects is conducted to improve the solar cell efficiency. The optimized device structure is determined to be Ni/ZnSnN₂/ZnON/ZTO/Al, achieving an efficiency of ≈19% with a short‐circuit current density (Jsc) of 20.05 mA cm − 2 and an open‐circuit voltage (Voc) of 1.1 V. These findings present a novel, eco‐friendly, scalable, and efficient thin film solar cell design unlike its predecessor fabricated with toxic and rare earth materials.
- 29 May 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (4)
Hard x-ray detection by using β-Ga2O3 devices fabricated through radiofrequency sputtering
This study examined the deposition, characteristics, and device performance of β-Ga2O3 thin films optimized for high-energy x-ray detection. β-Ga2O3 thin films were deposited through radiofrequency magnetron sputtering under various working pressures, oxygen flow rates, and substrate temperatures. Structural analysis through x-ray diffraction and Raman spectroscopy were confirmed. The deposition under a working pressure of 3 mTorr, an oxygen flow rate of 2 cubic centimeters per minute at standard temperature and pressure, and a substrate temperature of 600 °C exhibited the highest crystallinity and had well-defined (400), (020), and (3¯12) orientations. Atomic force microscopy and scanning electron microscopy revealed that films deposited under the above-mentioned parameters had the smoothest surface and uniform thickness. Optical characterization showed that deposition conditions significantly influenced the film’s bandgap and transmittance. The integration of β-Ga2O3 with an indium gallium zinc oxide (IGZO) charge transport layer substantially improved device performance. Peak photocurrents of 5.6 μA and 17.34 nA under 265-nm ultraviolet illumination and 50 keV x-ray illumination, respectively, were achieved. The device with an IGZO charge transport layer exhibited high sensitivity (493 μC/mGy cm2) and an excellent signal-to-noise ratio (3459.3) under 50 keV x-ray illumination.
- 29 May 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (4)
Hard x-ray detection by using β-Ga2O3 devices fabricated through radiofrequency sputtering
This study examined the deposition, characteristics, and device performance of β-Ga2O3 thin films optimized for high-energy x-ray detection. β-Ga2O3 thin films were deposited through radiofrequency magnetron sputtering under various working pressures, oxygen flow rates, and substrate temperatures. Structural analysis through x-ray diffraction and Raman spectroscopy were confirmed. The deposition under a working pressure of 3 mTorr, an oxygen flow rate of 2 cubic centimeters per minute at standard temperature and pressure, and a substrate temperature of 600 °C exhibited the highest crystallinity and had well-defined (400), (020), and (3¯12) orientations. Atomic force microscopy and scanning electron microscopy revealed that films deposited under the above-mentioned parameters had the smoothest surface and uniform thickness. Optical characterization showed that deposition conditions significantly influenced the film’s bandgap and transmittance. The integration of β-Ga2O3 with an indium gallium zinc oxide (IGZO) charge transport layer substantially improved device performance. Peak photocurrents of 5.6 μA and 17.34 nA under 265-nm ultraviolet illumination and 50 keV x-ray illumination, respectively, were achieved. The device with an IGZO charge transport layer exhibited high sensitivity (493 μC/mGy cm2) and an excellent signal-to-noise ratio (3459.3) under 50 keV x-ray illumination.
- 26 May 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (6) , 065973
Experimental fabrication and computational modelling of CuO-based semi-transparent solar cells with DMD top contacts
Inorganic materials hold immense potential for fabricating various optoelectronic devices. This study explores the fabrication and performance of semi-transparent solar cells (STSCs) featuring a CuO p-layer, an AZO n-layer, and a Dielectric/Metal/Dielectric (DMD) MoOx/Ti/MoOx top contact. CuO layers were sputtered at oxygen concentrations of 10%, 15%, and 20%, with the 20% oxygen concentration yielding the best results. The CuO (002) monoclinic phase was the most prominent, exhibiting a carrier concentration of 1.77 × 1016 cm−3, mobility of 4.47 cm2 V−1·s−1, and a transparency exceeding 48%. Meanwhile, the AZO layer demonstrated over 80% transmittance, a carrier concentration of 6.61 × 1020 cm−3, and mobility of 6.12 cm2/V·s. The DMD top contact exhibited more than 80% transparency, ensuring effective light management and high conductivity. Current–voltage (I-V) characterization revealed that the device with 20% oxygen concentration achieved an open-circuit voltage (Voc) of 0.95 V and an efficiency of 0.108%, indicating enhanced device performance. Theoretical calculations using SCAPS-1D were employed to analyse the I–V characteristics and quantum efficiency (QE) of the fabricated device, providing insights for performance optimization. Additionally, SCAPS-1D was used to evaluate the Average Visible Transmittance (AVT) and Light Utilization Efficiency (LUE) to further understand the device’s optical properties.
- 26 May 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (6) , 065973
Experimental fabrication and computational modelling of CuO-based semi-transparent solar cells with DMD top contacts
Inorganic materials hold immense potential for fabricating various optoelectronic devices. This study explores the fabrication and performance of semi-transparent solar cells (STSCs) featuring a CuO p-layer, an AZO n-layer, and a Dielectric/Metal/Dielectric (DMD) MoOx/Ti/MoOx top contact. CuO layers were sputtered at oxygen concentrations of 10%, 15%, and 20%, with the 20% oxygen concentration yielding the best results. The CuO (002) monoclinic phase was the most prominent, exhibiting a carrier concentration of 1.77 × 1016 cm−3, mobility of 4.47 cm2 V−1·s−1, and a transparency exceeding 48%. Meanwhile, the AZO layer demonstrated over 80% transmittance, a carrier concentration of 6.61 × 1020 cm−3, and mobility of 6.12 cm2/V·s. The DMD top contact exhibited more than 80% transparency, ensuring effective light management and high conductivity. Current–voltage (I-V) characterization revealed that the device with 20% oxygen concentration achieved an open-circuit voltage (Voc) of 0.95 V and an efficiency of 0.108%, indicating enhanced device performance. Theoretical calculations using SCAPS-1D were employed to analyse the I–V characteristics and quantum efficiency (QE) of the fabricated device, providing insights for performance optimization. Additionally, SCAPS-1D was used to evaluate the Average Visible Transmittance (AVT) and Light Utilization Efficiency (LUE) to further understand the device’s optical properties.