Zohreh Rahimi-Ahar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Zohreh Rahimi-Ahar has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Younes Ghalavand
5 shared publicationsMohammad Sadegh Hatamipour
4 shared publications- Mohammad Sadegh Hatamipour
Chemical Engineering Department, University of Isfahan, Isfahan, Iran
4 shared publications - Aziz Babapoor
Department of Chemical Engineering, Faculty of Engineering, Azarbaijan Shahid Madani University, Tabriz, Iran
2 shared publications Emad Ayati
2 shared publications- Helga Zabardast
University of Mohaghegh Ardabili
2 shared publications
Latest Publications
- 11 November 2026
- Published by Springer Nature
- p. 1-15
Role of Nanotechnology in Plastic Waste Degradation
- 11 November 2026
- Published by Springer Nature
- p. 1-15
Role of Nanotechnology in Plastic Waste Degradation
- 14 October 2026
- Published by Springer Nature
- p. 1-14
Introduction to Nanotechnology in Environmental Science
- 14 October 2026
- Published by Springer Nature
- p. 1-14
Introduction to Nanotechnology in Environmental Science
- 9 October 2026
- Published by Springer Nature
- p. 1-18
Nanomaterials for the Removal of Heavy Metals from Water
- 9 October 2026
- Published by Springer Nature
- p. 1-18
Nanomaterials for the Removal of Heavy Metals from Water
- 6 January 2026
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 11 (1) , 52
Enhancing asphalt and bitumen durability through advanced phase change materials
- 6 January 2026
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 11 (1) , 52
Enhancing asphalt and bitumen durability through advanced phase change materials
- Open Access
- 23 December 2024
- Published by SCI AND TECH UNIVERSAL INC in Scientia Iranica
Solar-Driven Desalination System Using Two Types of Evacuated Tube Collectors
Desalination is an appropriate response to climate change, increasing population, industrial activities, and drought. This study introduced a freshwater generation system using solar distillation via evacuated tube collectors (ETCs). Two geometries of evacuated tubes (Designs I and II) were used and the performance of the proposed system was evaluated regarding freshwater productivity, gained output ratio (GOR), and cost per liter (CPL). The difference between these tubes was the volume of the water circulating within them due to different internal geometry. No brine was produced and the system benefitted from zero liquid discharge technology. Maximum freshwater productivity values of 1145 and 1325 mL.h-1.m-2 were obtained for Designs (I) and (II), respectively. It occurred in June 2023 under a maximum solar radiation intensity of 1010 W.m-2. A maximum GOR of 0.71 and 0.82 was calculated at this peak solar radiation intensity for Designs (I) and (II), respectively. The quality of produced water met the standards of drinking water. The cost analysis led to the CPL of 0.0137 and 0.0132 US $ for Designs (I) and (II), respectively. The performance comparison of the proposed designs with other direct desalination units confirmed the superiority of these designs based on freshwater productivity, GOR, and CPL.
- 23 December 2024
- Published by SCI AND TECH UNIVERSAL INC in Scientia Iranica
Open AccessSolar-Driven Desalination System Using Two Types of Evacuated Tube Collectors
Desalination is an appropriate response to climate change, increasing population, industrial activities, and drought. This study introduced a freshwater generation system using solar distillation via evacuated tube collectors (ETCs). Two geometries of evacuated tubes (Designs I and II) were used and the performance of the proposed system was evaluated regarding freshwater productivity, gained output ratio (GOR), and cost per liter (CPL). The difference between these tubes was the volume of the water circulating within them due to different internal geometry. No brine was produced and the system benefitted from zero liquid discharge technology. Maximum freshwater productivity values of 1145 and 1325 mL.h-1.m-2 were obtained for Designs (I) and (II), respectively. It occurred in June 2023 under a maximum solar radiation intensity of 1010 W.m-2. A maximum GOR of 0.71 and 0.82 was calculated at this peak solar radiation intensity for Designs (I) and (II), respectively. The quality of produced water met the standards of drinking water. The cost analysis led to the CPL of 0.0137 and 0.0132 US $ for Designs (I) and (II), respectively. The performance comparison of the proposed designs with other direct desalination units confirmed the superiority of these designs based on freshwater productivity, GOR, and CPL.
- 2 September 2024
- Published by CSIRO Publishing in Environmental Chemistry
- Vol. 21 (6)
Methods and current developments of the Solvay process for brine management and CO2 capture: a critical review
Environmental context: This manuscript focuses on the introduction of the conventional and modified Solvay processes. The Solvay process is used to produce sodium carbonate and sodium bicarbonate, while also providing brine management and CO2 capture. Optimal values must be used for reactant contents, temperature, salinity of the brine and stirring rate to enhance efficiency. The Solvay process is used to produce sodium carbonate and sodium bicarbonate. Simultaneous brine management and CO2 capture occur by the Solvay process. In this review, the Solvay process based on different solutions (i.e. NH3, KOH, CaO, Ca(OH)2 and alcohol amines) is reviewed. The most efficient processes considering CO2 uptake and Na+/Cl− removal are introduced. The Solvay process benefits from increasing NH3 content, salinity, stirring rate, decreasing temperature and using inert mixing particles in the reactor. Adding NH4HCO3, extra KOH in subsequent stages and brine pretreatment are recommended. The results show that a Ca(OH)2-based Solvay process, an NH3-based process running in contactor and reactor, and a 2-amino-2-methylpropanol-based Solvay process obtain the highest CO2 capture efficiencies of 99, 98 and 80% respectively.
- 2 September 2024
- Published by CSIRO Publishing in Environmental Chemistry
- Vol. 21 (6)
Methods and current developments of the Solvay process for brine management and CO2 capture: a critical review
Environmental context: This manuscript focuses on the introduction of the conventional and modified Solvay processes. The Solvay process is used to produce sodium carbonate and sodium bicarbonate, while also providing brine management and CO2 capture. Optimal values must be used for reactant contents, temperature, salinity of the brine and stirring rate to enhance efficiency. The Solvay process is used to produce sodium carbonate and sodium bicarbonate. Simultaneous brine management and CO2 capture occur by the Solvay process. In this review, the Solvay process based on different solutions (i.e. NH3, KOH, CaO, Ca(OH)2 and alcohol amines) is reviewed. The most efficient processes considering CO2 uptake and Na+/Cl− removal are introduced. The Solvay process benefits from increasing NH3 content, salinity, stirring rate, decreasing temperature and using inert mixing particles in the reactor. Adding NH4HCO3, extra KOH in subsequent stages and brine pretreatment are recommended. The results show that a Ca(OH)2-based Solvay process, an NH3-based process running in contactor and reactor, and a 2-amino-2-methylpropanol-based Solvay process obtain the highest CO2 capture efficiencies of 99, 98 and 80% respectively.
- 25 July 2024
- Published by Elsevier in European Polymer Journal
- Vol. 218
Thermal, optical, mechanical, dielectric, and electrical properties of nanocomposites
- 25 July 2024
- Published by Elsevier in European Polymer Journal
- Vol. 218
Thermal, optical, mechanical, dielectric, and electrical properties of nanocomposites
- 7 August 2023
- Published by Elsevier in Materials Science and Engineering: B
- Vol. 297, 116799
Urea-Functionalized mesoporous silica SBA-15 for heavy metal Adsorption: Synthesis, Characterization, and optimization
- 7 August 2023
- Published by Elsevier in Materials Science and Engineering: B
- Vol. 297, 116799
Urea-Functionalized mesoporous silica SBA-15 for heavy metal Adsorption: Synthesis, Characterization, and optimization
- Open Access
- 12 June 2023
- Published by Springer Nature in Clean Technologies and Environmental Policy
- Vol. 25 (7) , 2157-2184
Performance evaluation of single stand and hybrid solar water heaters: a comprehensive review
In this review, flat plate and concentrate-type solar collectors, integrated collector–storage systems, and solar water heaters combined with photovoltaic–thermal modules, solar-assisted heat pump solar water heaters, and solar water heaters using phase change materials are studied based on their thermal performance, cost, energy, and exergy efficiencies. The maximum water temperature and thermal efficiencies are enlisted to evaluate the thermal performance of the different solar water heaters. It is found that the solar water heaters’ performance is considerably improved by boosting water flow rate and tilt angle, modification of the shape and number of collectors, using wavy diffuse and electrodepositioned reflector coating, application of the corrugated absorber surface and coated absorber, use of turbulent enhancers, using thermal conductive working fluid and nanofluid, the inclusion of the water storage tank, and tank insulation. These items increase the heat transfer area and coefficient, thermal conductivity, the Reynolds and Nusselt numbers, heat transfer rate, and energy and exergy efficiencies. The evacuated tube heaters have a higher temperature compared to the collectors with a plane surface. Their thermal performance increases by using all-glass active circulation and heat pipe integration. The concentrative type of solar water heaters is superior to other solar heaters, particularly in achieving higher water temperatures. Their performance improves by using a rotating mirror concentrator. The integration of the system with energy storage components, phase change materials, or a heat pump provides a satisfactory performance over conventional solar water heaters. Graphical abstract Modification of solar water heaters
- 12 June 2023
- Published by Springer Nature in Clean Technologies and Environmental Policy
- Vol. 25 (7) , 2157-2184
Open AccessPerformance evaluation of single stand and hybrid solar water heaters: a comprehensive review
In this review, flat plate and concentrate-type solar collectors, integrated collector–storage systems, and solar water heaters combined with photovoltaic–thermal modules, solar-assisted heat pump solar water heaters, and solar water heaters using phase change materials are studied based on their thermal performance, cost, energy, and exergy efficiencies. The maximum water temperature and thermal efficiencies are enlisted to evaluate the thermal performance of the different solar water heaters. It is found that the solar water heaters’ performance is considerably improved by boosting water flow rate and tilt angle, modification of the shape and number of collectors, using wavy diffuse and electrodepositioned reflector coating, application of the corrugated absorber surface and coated absorber, use of turbulent enhancers, using thermal conductive working fluid and nanofluid, the inclusion of the water storage tank, and tank insulation. These items increase the heat transfer area and coefficient, thermal conductivity, the Reynolds and Nusselt numbers, heat transfer rate, and energy and exergy efficiencies. The evacuated tube heaters have a higher temperature compared to the collectors with a plane surface. Their thermal performance increases by using all-glass active circulation and heat pipe integration. The concentrative type of solar water heaters is superior to other solar heaters, particularly in achieving higher water temperatures. Their performance improves by using a rotating mirror concentrator. The integration of the system with energy storage components, phase change materials, or a heat pump provides a satisfactory performance over conventional solar water heaters. Graphical abstract Modification of solar water heaters
- 3 March 2023
- Published by Springer Nature in Clean Technologies and Environmental Policy
- Vol. 26 (5) , 1335-1362
Exergy analysis of thermal desalination processes: a review
- 3 March 2023
- Published by Springer Nature in Clean Technologies and Environmental Policy
- Vol. 26 (5) , 1335-1362
Exergy analysis of thermal desalination processes: a review