Anthony H. McDaniel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Anthony H. McDaniel has a total of 130 co-authors. Here are the top co-authors by number of shared publications:
- Matthew Witman
Sandia National Laboratories
6 shared publications - Stephan Lany
National Laboratory of the Rockies
5 shared publications - Sean Robert Bishop
Sandia National Laboratories
4 shared publications - Eric Nicholas Coker
Sandia National Laboratories
3 shared publications - Nicholas A. Strange
Stanford Synchrotron Radiation Lightsource
3 shared publications - Robert B. Wexler
Washington University in St. Louis
3 shared publications
Latest Publications
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (42) , 2141
Oxygen Non-Stoichiometry and Thermochemical Hydrogen Production of Novel Machine Learned Oxides
Thermochemical hydrogen production (TCH) is a promising approach to convert water into hydrogen by utilizing thermal energy from sources such as concentrated solar energy, as opposed to using electricity in electrochemical methods. This process consists of two main steps: first, a material undergoes thermal reduction at elevated temperatures (~ 1300 - 1500 °C) under low oxygen partial pressures (pO2) of ~10-3 -10 -5 atm, which results in the formation of oxygen vacancies. Next, the temperature of the system is reduced to ~800 - 1000 °C in the presence of steam, enabling water splitting through material oxidation. The commercial feasibility of TCH is dependent on identifying a material with an optimal reduction enthalpy that supports both the thermal reduction of redox-active cations and their re-oxidation, while also possessing high cycle stability. Perovskite metal oxides have received significant interest as potential TCH materials due to their ability to accommodate high concentrations of oxygen vacancies and their highly tunable thermodynamic properties. However, these materials often exhibit low hydrogen production due to re-oxidation and poor cycle stability challenges.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (42) , 2141
Oxygen Non-Stoichiometry and Thermochemical Hydrogen Production of Novel Machine Learned Oxides
Thermochemical hydrogen production (TCH) is a promising approach to convert water into hydrogen by utilizing thermal energy from sources such as concentrated solar energy, as opposed to using electricity in electrochemical methods. This process consists of two main steps: first, a material undergoes thermal reduction at elevated temperatures (~ 1300 - 1500 °C) under low oxygen partial pressures (pO2) of ~10-3 -10 -5 atm, which results in the formation of oxygen vacancies. Next, the temperature of the system is reduced to ~800 - 1000 °C in the presence of steam, enabling water splitting through material oxidation. The commercial feasibility of TCH is dependent on identifying a material with an optimal reduction enthalpy that supports both the thermal reduction of redox-active cations and their re-oxidation, while also possessing high cycle stability. Perovskite metal oxides have received significant interest as potential TCH materials due to their ability to accommodate high concentrations of oxygen vacancies and their highly tunable thermodynamic properties. However, these materials often exhibit low hydrogen production due to re-oxidation and poor cycle stability challenges.
- Open Access
- 10 April 2026
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 19 (8) , 2507-2535
Advanced pathways for hydrogen production: a collective view from a technical experts meeting
Hydrogen is an essential fuel and feedstock that can be produced in multiple ways to meet requirements for technological sectors that include energy storage, transportation, petroleum refining, and ammonia synthesis. To consider the future state of hydrogen manufacturing, a team of experts has assembled and examined three emerging hydrogen production technologies – photoelectrochemical, biological, and thermochemical. Each of these emerging technologies holds significant long-term potential for cost reduction while lowering industrial emissions associated with conventional methods of hydrogen manufacture (e.g., steam methane reforming) by using sunlight and renewable resources as primary sources of energy and feedstock, respectively. All three are currently at low technology readiness levels, however their applications, cost reduction opportunities and performance improvement pathways are under active development. In this work, opportunities and outlook for research that can directly advance the technologies are discussed.
- 10 April 2026
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 19 (8) , 2507-2535
Open AccessAdvanced pathways for hydrogen production: a collective view from a technical experts meeting
Hydrogen is an essential fuel and feedstock that can be produced in multiple ways to meet requirements for technological sectors that include energy storage, transportation, petroleum refining, and ammonia synthesis. To consider the future state of hydrogen manufacturing, a team of experts has assembled and examined three emerging hydrogen production technologies – photoelectrochemical, biological, and thermochemical. Each of these emerging technologies holds significant long-term potential for cost reduction while lowering industrial emissions associated with conventional methods of hydrogen manufacture (e.g., steam methane reforming) by using sunlight and renewable resources as primary sources of energy and feedstock, respectively. All three are currently at low technology readiness levels, however their applications, cost reduction opportunities and performance improvement pathways are under active development. In this work, opportunities and outlook for research that can directly advance the technologies are discussed.
- 26 January 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (2) , 829-839
Large-scale experimental validation of thermochemical water-splitting oxides discovered by defect graph neural networks
To identify promising metal oxides for thermochemical water-splitting, we propose a workflow involving defect machine learning model training, high-throughput computational screening, material down-selection, and experimental validation.
- 26 January 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (2) , 829-839
Large-scale experimental validation of thermochemical water-splitting oxides discovered by defect graph neural networks
To identify promising metal oxides for thermochemical water-splitting, we propose a workflow involving defect machine learning model training, high-throughput computational screening, material down-selection, and experimental validation.
- Open Access
- 5 May 2025
- Published by American Chemical Society (ACS) in ChemRxiv
LASSO for CALPHAD model selection enables data-efficient thermodynamic modeling: an application in thermochemical hydrogen production materials
Phenomenological CALPHAD (CALculation of PHAse Diagrams) models, widely used for multicomponent materials, often contain a considerable number of parameters and require fitting using data from a relatively small number of experimental measurements or theoretical calculations. Sometimes these parameters are introduced for the purpose of improving model fits but without clear physical justification, which leads to over-parameterized models with poor generalization performance. Automated approaches for optimal model selection based on the available data therefore become critical. In this work, a least absolute shrinkage and selection operator (LASSO)-based approach is developed for model selection by leveraging the linearity of the CALPHAD model with respect to its parameters to convert the model selection and fitting to a LASSO minimization problem. We demonstrate its utility for thermodynamic modeling of thermochemical hydrogen (TCH) production materials, using lanthanum strontium manganite (LSM) as an example. Various TCH relevant properties, including oxygen stoichiometry as function of oxygen partial pressure, enthalpy of reduction, and entropy of reduction, are successfully predicted with reasonable accuracy using a minimal set of model parameters. Importantly, the model selection and fitting involve minimal human decision; it can therefore be applied to high-throughput DFT defect calculations and yield efficient workflows for TCH materials modeling and optimization.
- 5 May 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessLASSO for CALPHAD model selection enables data-efficient thermodynamic modeling: an application in thermochemical hydrogen production materials
Phenomenological CALPHAD (CALculation of PHAse Diagrams) models, widely used for multicomponent materials, often contain a considerable number of parameters and require fitting using data from a relatively small number of experimental measurements or theoretical calculations. Sometimes these parameters are introduced for the purpose of improving model fits but without clear physical justification, which leads to over-parameterized models with poor generalization performance. Automated approaches for optimal model selection based on the available data therefore become critical. In this work, a least absolute shrinkage and selection operator (LASSO)-based approach is developed for model selection by leveraging the linearity of the CALPHAD model with respect to its parameters to convert the model selection and fitting to a LASSO minimization problem. We demonstrate its utility for thermodynamic modeling of thermochemical hydrogen (TCH) production materials, using lanthanum strontium manganite (LSM) as an example. Various TCH relevant properties, including oxygen stoichiometry as function of oxygen partial pressure, enthalpy of reduction, and entropy of reduction, are successfully predicted with reasonable accuracy using a minimal set of model parameters. Importantly, the model selection and fitting involve minimal human decision; it can therefore be applied to high-throughput DFT defect calculations and yield efficient workflows for TCH materials modeling and optimization.
- Open Access
- 28 August 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Defect diffusion graph neural networks for materials discovery in high-temperature, clean energy applications
The migration of crystallographic defects dictates material properties and performance for a plethora of technological applications. Density functional theory (DFT)-based nudged elastic band (NEB) calculations are a powerful computational technique for predicting defect migration activation energy barriers, yet they become prohibitively expensive for high-throughput screening of defect diffusivities. Without introducing hand-crafted (i.e., chemistry- or structure-specific) descriptors, we propose a generalized deep learning approach to train surrogate models for NEB energies of vacancy migration by hybridizing graph neural networks with transformer encoders and simply using pristine host structures as input. With sufficient training data, computationally efficient and simultaneous inference of vacancy defect thermodynamics and migration activation energies can be obtained to compute temperature-dependent vacancy diffusivities and to down-select candidates for more thorough DFT analysis or experiments. Thus, as we specifically demonstrate for potential water-splitting materials, candidates with desired defect thermodynamics, kinetics, and host stability properties can be more rapidly targeted from open-source databases of experimentally validated or hypothetical materials.
- 28 August 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessDefect diffusion graph neural networks for materials discovery in high-temperature, clean energy applications
The migration of crystallographic defects dictates material properties and performance for a plethora of technological applications. Density functional theory (DFT)-based nudged elastic band (NEB) calculations are a powerful computational technique for predicting defect migration activation energy barriers, yet they become prohibitively expensive for high-throughput screening of defect diffusivities. Without introducing hand-crafted (i.e., chemistry- or structure-specific) descriptors, we propose a generalized deep learning approach to train surrogate models for NEB energies of vacancy migration by hybridizing graph neural networks with transformer encoders and simply using pristine host structures as input. With sufficient training data, computationally efficient and simultaneous inference of vacancy defect thermodynamics and migration activation energies can be obtained to compute temperature-dependent vacancy diffusivities and to down-select candidates for more thorough DFT analysis or experiments. Thus, as we specifically demonstrate for potential water-splitting materials, candidates with desired defect thermodynamics, kinetics, and host stability properties can be more rapidly targeted from open-source databases of experimentally validated or hypothetical materials.
- 30 April 2024
- Published by Office of Scientific and Technical Information (OSTI)
Technical Evaluation of Electrochemical Redox Cycle for Hydrogen Production, Heat Augmentation, and Energy Arbitrage
Under the U.S. Department of Energy’s (DOE’s) Light Water Reactor Sustainability (LWRS) Program’s Flexible Plant Operation and Generation (FPOG) Pathway, research is performed to show how existing light-water reactors (LWRs) can flexibly provide heat and power to industrial processes to improve process cost and efficiency while diversifying their revenue sources. Researchers from Sandia National Laboratories (SNL) have proposed a process for splitting water into gaseous hydrogen and oxygen through a two-step liquid-metal-mediated process. First, steam oxidizes a reactive metal, producing hydrogen. The resulting metal oxide is then electrochemically reduced to regenerate the metal by off-gassing oxygen. This process is completed at high temperature and low pressure. Each step has been experimentally demonstrated at the bench-top scale at SNL. An LWR could provide heat and power to this process to enable scaling and more-efficient operation. The purpose of this present work is to model a scaled-up design of this process focused on the exploration of this electrochemical metal-redox cycle using energy inputs from an LWR nuclear power plant (NPP). The scale chosen was 500 MWe alternating current (AC) input to the process. Three use cases have been envisioned for this novel process, including: 1. Hydrogen production 2. Heat augmentation 3. Energy Arbitrage. The cycle’s ability to perform in these three key areas is analyzed in this study.
- 30 April 2024
- Published by Office of Scientific and Technical Information (OSTI)
Technical Evaluation of Electrochemical Redox Cycle for Hydrogen Production, Heat Augmentation, and Energy Arbitrage
Under the U.S. Department of Energy’s (DOE’s) Light Water Reactor Sustainability (LWRS) Program’s Flexible Plant Operation and Generation (FPOG) Pathway, research is performed to show how existing light-water reactors (LWRs) can flexibly provide heat and power to industrial processes to improve process cost and efficiency while diversifying their revenue sources. Researchers from Sandia National Laboratories (SNL) have proposed a process for splitting water into gaseous hydrogen and oxygen through a two-step liquid-metal-mediated process. First, steam oxidizes a reactive metal, producing hydrogen. The resulting metal oxide is then electrochemically reduced to regenerate the metal by off-gassing oxygen. This process is completed at high temperature and low pressure. Each step has been experimentally demonstrated at the bench-top scale at SNL. An LWR could provide heat and power to this process to enable scaling and more-efficient operation. The purpose of this present work is to model a scaled-up design of this process focused on the exploration of this electrochemical metal-redox cycle using energy inputs from an LWR nuclear power plant (NPP). The scale chosen was 500 MWe alternating current (AC) input to the process. Three use cases have been envisioned for this novel process, including: 1. Hydrogen production 2. Heat augmentation 3. Energy Arbitrage. The cycle’s ability to perform in these three key areas is analyzed in this study.
- Open Access
- 3 January 2024
- Published by TIB Open Publishing in SolarPACES Conference Proceedings
- Vol. 1
Experimental Investigation of a System of Two Vacuum Solar Receivers for the Continuous Reduction of Ceria Particles
A solar receiver for the continuous reduction of redox particles under vacuum conditions has been developed previously as part of a system to produce hydrogen from solar energy. Here, we report about a joint effort of Sandia and DLR to improve the receivers design and to demonstrate a system of two receivers with different vacuum pressures at DLR’s solar simulator Synlight. We focus on the design and experimental investigation of three components: the novel beam down mirror, the novel secondary concentrator and the improved version of the particle conveying plate in the receiver. Irradiation test results and heat transfer analyses of the beam-down mirror and the secondary concentrator are being presented. The motion of the conveyor plate was improved by a MATLAB model, which predicts the transport speed of the particles on the conveyor.
- 3 January 2024
- Published by TIB Open Publishing in SolarPACES Conference Proceedings
- Vol. 1
Open AccessExperimental Investigation of a System of Two Vacuum Solar Receivers for the Continuous Reduction of Ceria Particles
A solar receiver for the continuous reduction of redox particles under vacuum conditions has been developed previously as part of a system to produce hydrogen from solar energy. Here, we report about a joint effort of Sandia and DLR to improve the receivers design and to demonstrate a system of two receivers with different vacuum pressures at DLR’s solar simulator Synlight. We focus on the design and experimental investigation of three components: the novel beam down mirror, the novel secondary concentrator and the improved version of the particle conveying plate in the receiver. Irradiation test results and heat transfer analyses of the beam-down mirror and the secondary concentrator are being presented. The motion of the conveyor plate was improved by a MATLAB model, which predicts the transport speed of the particles on the conveyor.
- 27 September 2023
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 146 (2) , 1-13
Assessment of Bulk Oxygen Capacity and Transient Redox Behavior of Foamed Lanthanum Strontium Manganese Perovskites
Synthesis of solar thermochemical H2 (STCH) production redox materials with engineered structures, for example replica foams, can enable efficient heat and mass transport and are critical for scaled-up systems. Prior work has motivated the use of LSM-type perovskites as foamed STCH materials, but the effect of their morphology on bulk and kinetic behavior has not been reported. In this work, replica and direct foamed samples of La0.65Sr0.35MnO3-δ (LSM35) were fabricated and compared to synthesized powders and dense monoliths, and similarly synthesized CeO2-δ (ceria) foams, regarding their specific reaction rates and bulk oxygen capacity/H2 yields. Changes in oxygen capacity (Δδ) and reaction rates were measured between 1200 °C −1400 °C by using fixed ratios of steam and hydrogen during both reduction and oxidation steps, allowing for analysis under practical high conversion conditions. Results suggest bulk behavior and reaction rates of the foamed LSM materials are comparable to their powder analogues. Differences in reaction rates were observed only when replica foamed samples were subjected to rapid laser heating (emulating conditions expected in solar furnaces), which is expected but has not been demonstrated at such a small scale. Foamed samples were further subjected to 50 redox cycles at 1400 °C to evaluate their stability. Results show no statistically significant decrease in hydrogen production for any of the foamed samples, but the direct foamed samples became brittle with time. Together, these results demonstrate the viability of replica foamed LSM perovskites for integration in scaled up STCH systems.
- 27 September 2023
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 146 (2) , 1-13
Assessment of Bulk Oxygen Capacity and Transient Redox Behavior of Foamed Lanthanum Strontium Manganese Perovskites
Synthesis of solar thermochemical H2 (STCH) production redox materials with engineered structures, for example replica foams, can enable efficient heat and mass transport and are critical for scaled-up systems. Prior work has motivated the use of LSM-type perovskites as foamed STCH materials, but the effect of their morphology on bulk and kinetic behavior has not been reported. In this work, replica and direct foamed samples of La0.65Sr0.35MnO3-δ (LSM35) were fabricated and compared to synthesized powders and dense monoliths, and similarly synthesized CeO2-δ (ceria) foams, regarding their specific reaction rates and bulk oxygen capacity/H2 yields. Changes in oxygen capacity (Δδ) and reaction rates were measured between 1200 °C −1400 °C by using fixed ratios of steam and hydrogen during both reduction and oxidation steps, allowing for analysis under practical high conversion conditions. Results suggest bulk behavior and reaction rates of the foamed LSM materials are comparable to their powder analogues. Differences in reaction rates were observed only when replica foamed samples were subjected to rapid laser heating (emulating conditions expected in solar furnaces), which is expected but has not been demonstrated at such a small scale. Foamed samples were further subjected to 50 redox cycles at 1400 °C to evaluate their stability. Results show no statistically significant decrease in hydrogen production for any of the foamed samples, but the direct foamed samples became brittle with time. Together, these results demonstrate the viability of replica foamed LSM perovskites for integration in scaled up STCH systems.
- 10 August 2023
- Published by Springer Nature in Nature Computational Science
- Vol. 3 (8) , 675-686
Defect graph neural networks for materials discovery in high-temperature clean-energy applications
We present a graph neural network approach that fully automates the prediction of defect formation enthalpies for any crystallographic site from the ideal crystal structure, without the need to create defected atomic structure models as input. Here we used density functional theory reference data for vacancy defects in oxides, to train a defect graph neural network (dGNN) model that replaces the density functional theory supercell relaxations otherwise required for each symmetrically unique crystal site. Interfaced with thermodynamic calculations of reduction entropies and associated free energies, the dGNN model is applied to the screening of oxides in the Materials Project database, connecting the zero-kelvin defect enthalpies to high-temperature process conditions relevant for solar thermochemical hydrogen production and other energy applications. The dGNN approach is applicable to arbitrary structures with an accuracy limited principally by the amount and diversity of the training data, and it is generalizable to other defect types and advanced graph convolution architectures. It will help to tackle future materials discovery problems in clean energy and beyond.
- 10 August 2023
- Published by Springer Nature in Nature Computational Science
- Vol. 3 (8) , 675-686
Defect graph neural networks for materials discovery in high-temperature clean-energy applications
We present a graph neural network approach that fully automates the prediction of defect formation enthalpies for any crystallographic site from the ideal crystal structure, without the need to create defected atomic structure models as input. Here we used density functional theory reference data for vacancy defects in oxides, to train a defect graph neural network (dGNN) model that replaces the density functional theory supercell relaxations otherwise required for each symmetrically unique crystal site. Interfaced with thermodynamic calculations of reduction entropies and associated free energies, the dGNN model is applied to the screening of oxides in the Materials Project database, connecting the zero-kelvin defect enthalpies to high-temperature process conditions relevant for solar thermochemical hydrogen production and other energy applications. The dGNN approach is applicable to arbitrary structures with an accuracy limited principally by the amount and diversity of the training data, and it is generalizable to other defect types and advanced graph convolution architectures. It will help to tackle future materials discovery problems in clean energy and beyond.
- Open Access
- 5 January 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Materials discovery for high-temperature, clean-energy applications using graph neural network models of vacancy defects and free-energy calculations
We present a graph neural network modeling approach that fully automates the prediction of the DFT-relaxed vacancy formation enthalpy of any crystallographic site from its DFT-relaxed host structure. Applicable to arbitrary structures with an accuracy limited principally by the amount/diversity of the data on which it is trained, this model accelerates the screening of vacancy defects by many orders of magnitude by replacing the DFT supercell relaxations required for each symmetrically unique crystal site. It can thus be used off-the-shelf to rapidly screen 10,000s of crystal structures (which can contain millions of unique defects) from existing databases of DFT-relaxed crystal structures. This modeling approach therefore provides a significant screening and discovery capability for a plethora of applications in which vacancy defects are the primary driver of a material's utility. For example, by high-throughput screening the Materials Project's metal oxides, we rapidly "re-discover" and identify new high potential candidate materials for hydrogen generation via solar thermochemical water splitting and energy storage, for CO2 conversion via reverse water gas shift chemical looping, and for cathodes in solid oxide fuel cells. Thermodynamic modeling on the basis of the high-throughput screening results allows us to connect the predicted defect energies to high temperature process conditions relevant to the different application areas, and we extract the reduction entropies as an additional selection criterion for high-performance materials. Further model development and accumulation of additional training data will only serve to expand the significant utility of this generalizable defect model to solving materials discovery problems in clean energy applications and beyond.
- 5 January 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessMaterials discovery for high-temperature, clean-energy applications using graph neural network models of vacancy defects and free-energy calculations
We present a graph neural network modeling approach that fully automates the prediction of the DFT-relaxed vacancy formation enthalpy of any crystallographic site from its DFT-relaxed host structure. Applicable to arbitrary structures with an accuracy limited principally by the amount/diversity of the data on which it is trained, this model accelerates the screening of vacancy defects by many orders of magnitude by replacing the DFT supercell relaxations required for each symmetrically unique crystal site. It can thus be used off-the-shelf to rapidly screen 10,000s of crystal structures (which can contain millions of unique defects) from existing databases of DFT-relaxed crystal structures. This modeling approach therefore provides a significant screening and discovery capability for a plethora of applications in which vacancy defects are the primary driver of a material's utility. For example, by high-throughput screening the Materials Project's metal oxides, we rapidly "re-discover" and identify new high potential candidate materials for hydrogen generation via solar thermochemical water splitting and energy storage, for CO2 conversion via reverse water gas shift chemical looping, and for cathodes in solid oxide fuel cells. Thermodynamic modeling on the basis of the high-throughput screening results allows us to connect the predicted defect energies to high temperature process conditions relevant to the different application areas, and we extract the reduction entropies as an additional selection criterion for high-performance materials. Further model development and accumulation of additional training data will only serve to expand the significant utility of this generalizable defect model to solving materials discovery problems in clean energy applications and beyond.