In Wook Nah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
In Wook Nah has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
Beom-Seo Kim
3 shared publications- Faizan Ghani
School of Mechanical and Aerospace Engineering, Konkuk University, 120 Neungdong-ro, Gwangjin-gu, Seoul 05029, Republic of Korea
3 shared publications In Gyeom Kim
Department of Chemical and Biological Engineering Korea University Seoul Republic of Korea
3 shared publicationsJae-Yong Byeon
3 shared publicationsSang-Hyeok Yoon
3 shared publications- Abu Ul Hassan Sarwar Rana
Department of Electrical and Electronic Engineering, The University of Melbourne, Parkville, VIC 3010, Australia
2 shared publications
Latest Publications
- 11 September 2026
- Published by Elsevier in Applied Catalysis A: General
- Vol. 727
Synthesis of porous sodium phosphate solid base catalysts via wet precipitation and their application to glycerol carbonate production
- 11 September 2026
- Published by Elsevier in Applied Catalysis A: General
- Vol. 727
Synthesis of porous sodium phosphate solid base catalysts via wet precipitation and their application to glycerol carbonate production
- Open Access
- 25 May 2026
- Published by Elsevier in SSRN Electronic Journal
Synthesis of porous sodium phosphate solid base catalysts via wet precipitation and their application to glycerol carbonate production
Surplus glycerol, an environmental and economic byproduct of the biodiesel industry, has strong potential for high-value valorization via transesterification to glycerol carbonate (GC). This reaction is typically facilitated under alkaline conditions; however, the development of efficient solid base catalysts that operate under mild conditions remains highly desirable. In this study, sodium phosphate-based solid base catalysts (SSP_X) were synthesized via a wet precipitation method, and the effects of synthesis temperature on their structural properties and basicity were systematically investigated. Among the prepared catalysts, SSP_50 exhibited the best catalytic performance, affording an 81.14% GC yield within 5 min at 50 °C. Structural characterization showed that the wet precipitation method generated finely assembled porous particles with improved surface accessibility compared with those of commercially available sodium phosphate-based catalysts. CO2 temperature-programmed desorption analysis revealed that SSP_50 possessed high total basicity together with a balanced fraction of strong basic sites, which promoted rapid transesterification while suppressing side reactions under the tested conditions. These results demonstrate that wet-precipitated sodium phosphate catalysts provide a simple, scalable, and cost-effective platform for efficient GC synthesis from glycerol under mild operating conditions. The present strategy also offers potential for the broader design of phosphate-based solid base catalysts for biomass valorization and other base-catalyzed transformations.
- 25 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSynthesis of porous sodium phosphate solid base catalysts via wet precipitation and their application to glycerol carbonate production
Surplus glycerol, an environmental and economic byproduct of the biodiesel industry, has strong potential for high-value valorization via transesterification to glycerol carbonate (GC). This reaction is typically facilitated under alkaline conditions; however, the development of efficient solid base catalysts that operate under mild conditions remains highly desirable. In this study, sodium phosphate-based solid base catalysts (SSP_X) were synthesized via a wet precipitation method, and the effects of synthesis temperature on their structural properties and basicity were systematically investigated. Among the prepared catalysts, SSP_50 exhibited the best catalytic performance, affording an 81.14% GC yield within 5 min at 50 °C. Structural characterization showed that the wet precipitation method generated finely assembled porous particles with improved surface accessibility compared with those of commercially available sodium phosphate-based catalysts. CO2 temperature-programmed desorption analysis revealed that SSP_50 possessed high total basicity together with a balanced fraction of strong basic sites, which promoted rapid transesterification while suppressing side reactions under the tested conditions. These results demonstrate that wet-precipitated sodium phosphate catalysts provide a simple, scalable, and cost-effective platform for efficient GC synthesis from glycerol under mild operating conditions. The present strategy also offers potential for the broader design of phosphate-based solid base catalysts for biomass valorization and other base-catalyzed transformations.
- 5 November 2025
- Published by Springer Nature in Korean Journal of Chemical Engineering
- Vol. 43 (2) , 321-335
Optimization of a Recyclable Sodium-Based Heterogeneous Catalyst for Efficient DMC Synthesis Under Mild Conditions
- 5 November 2025
- Published by Springer Nature in Korean Journal of Chemical Engineering
- Vol. 43 (2) , 321-335
Optimization of a Recyclable Sodium-Based Heterogeneous Catalyst for Efficient DMC Synthesis Under Mild Conditions
- Open Access
- 13 June 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1
Publisher Correction: Production of abiotic or biogenic hydrocarbons on rock particles in the presence of H2O and carbon compounds
- 13 June 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1
Open AccessPublisher Correction: Production of abiotic or biogenic hydrocarbons on rock particles in the presence of H2O and carbon compounds
- Open Access
- 15 January 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-11
Production of abiotic or biogenic hydrocarbons on rock particles in the presence of H2O and carbon compounds
Abiotic H2 and hydrocarbons are found in fluids discharged from ultramafic-hosted hydrothermal vents. Beneath the hydrothermal vents, abiotic H2 and hydrocarbons can be formed by serpentinization reactions and Fischer–Tropsch-type hydrocarbon-forming reactions, respectively, over ultramafic rocks. However, the source rocks that form abiotic H2 and hydrocarbons may extend to broader subsurface rocks. Here, we show that various rock constituents (solid acids) play a catalytic role in the formation of H and OH radicals via H2O dissociation, as well as in the formation of diverse hydrocarbons via the synthesis reactions of H radicals and inorganic carbons or by H radical-induced dissociation of organic carbons. The mechanisms and characteristics of these formation processes were explored through a series of reactor-based laboratory experiments. Four types of solid acid-containing rocks were mixed with H2O and a carbon source and reacted at different temperatures and pressures for different reaction periods. The product gases were analyzed via GC/MS. Twenty-nine hydrocarbons up to C11, predominantly including CH4 and aromatic hydrocarbons, were identified when CO2 (inorganic carbon source) and basalt particles were used; in contrast, 42 hydrocarbons up to C11, predominantly including CH4 and aliphatic hydrocarbons, were identified when soybean oil (organic carbon source) and basalt particles were used. The results of this study imply that abiotic H2 and diverse hydrocarbons are produced in the subsurface of Earth regardless of the presence of living organisms and suggest that solid acid-containing rocks near hot springs or volcanic areas can promote CO2 conversion into CH4 with the aid of H radicals supplied from H2O dissociation over the rocks.
- 15 January 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-11
Open AccessProduction of abiotic or biogenic hydrocarbons on rock particles in the presence of H2O and carbon compounds
Abiotic H2 and hydrocarbons are found in fluids discharged from ultramafic-hosted hydrothermal vents. Beneath the hydrothermal vents, abiotic H2 and hydrocarbons can be formed by serpentinization reactions and Fischer–Tropsch-type hydrocarbon-forming reactions, respectively, over ultramafic rocks. However, the source rocks that form abiotic H2 and hydrocarbons may extend to broader subsurface rocks. Here, we show that various rock constituents (solid acids) play a catalytic role in the formation of H and OH radicals via H2O dissociation, as well as in the formation of diverse hydrocarbons via the synthesis reactions of H radicals and inorganic carbons or by H radical-induced dissociation of organic carbons. The mechanisms and characteristics of these formation processes were explored through a series of reactor-based laboratory experiments. Four types of solid acid-containing rocks were mixed with H2O and a carbon source and reacted at different temperatures and pressures for different reaction periods. The product gases were analyzed via GC/MS. Twenty-nine hydrocarbons up to C11, predominantly including CH4 and aromatic hydrocarbons, were identified when CO2 (inorganic carbon source) and basalt particles were used; in contrast, 42 hydrocarbons up to C11, predominantly including CH4 and aliphatic hydrocarbons, were identified when soybean oil (organic carbon source) and basalt particles were used. The results of this study imply that abiotic H2 and diverse hydrocarbons are produced in the subsurface of Earth regardless of the presence of living organisms and suggest that solid acid-containing rocks near hot springs or volcanic areas can promote CO2 conversion into CH4 with the aid of H radicals supplied from H2O dissociation over the rocks.
- 28 July 2021
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 100 (8) , 1755-1763
Preparation of polyvinyl alcohol–chitosan–NH4Br catalyst and its application to cycloaddition of carbon dioxide to propylene oxide
An eco‐friendly polyvinyl alcohol (PVA)–chitosan(CS)–NH4Br catalyst was prepared using a modified solution method. Although the amounts of PVA and CS were fixed, the amount of NH4Br was varied in the range 15–45 wt.%. The catalytic performance of PVA–CS–NH4Br was compared based on the carbonation performance in the presence of single‐component catalysts (PVA, CS, and NH4Br) and dual component catalyst (PVA–CS). The catalytic activity of PVA–CS was inadequate and considerably less than that observed when either PVA or CS was exclusively loaded. The number of functional groups within the PVA–CS structure was presumed to have been reduced due to the interactions of the OH groups in PVA and CS. However, the PVA–CS–NH4Br catalyst distinctively exhibited its catalytic performance. It has been suggested that NH4Br aided in sustaining the innate functional groups that both PVA and CS have within the PVA–CS–NH4Br structure. These results indicate that the functional groups and nucleophiles within the PVA–CS–NH4Br structure more effectively participated in the carbonation of propylene oxide. Quantitatively, the addition of 30 wt.% NH4Br yielded the best performance. Characteristic analyses of the catalysts were performed using X‐ray diffraction, thermogravimetric analysis, Fourier transform infrared spectroscopy, and X‐ray photoelectron spectroscopy.
- 28 July 2021
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 100 (8) , 1755-1763
Preparation of polyvinyl alcohol–chitosan–NH4Br catalyst and its application to cycloaddition of carbon dioxide to propylene oxide
An eco‐friendly polyvinyl alcohol (PVA)–chitosan(CS)–NH4Br catalyst was prepared using a modified solution method. Although the amounts of PVA and CS were fixed, the amount of NH4Br was varied in the range 15–45 wt.%. The catalytic performance of PVA–CS–NH4Br was compared based on the carbonation performance in the presence of single‐component catalysts (PVA, CS, and NH4Br) and dual component catalyst (PVA–CS). The catalytic activity of PVA–CS was inadequate and considerably less than that observed when either PVA or CS was exclusively loaded. The number of functional groups within the PVA–CS structure was presumed to have been reduced due to the interactions of the OH groups in PVA and CS. However, the PVA–CS–NH4Br catalyst distinctively exhibited its catalytic performance. It has been suggested that NH4Br aided in sustaining the innate functional groups that both PVA and CS have within the PVA–CS–NH4Br structure. These results indicate that the functional groups and nucleophiles within the PVA–CS–NH4Br structure more effectively participated in the carbonation of propylene oxide. Quantitatively, the addition of 30 wt.% NH4Br yielded the best performance. Characteristic analyses of the catalysts were performed using X‐ray diffraction, thermogravimetric analysis, Fourier transform infrared spectroscopy, and X‐ray photoelectron spectroscopy.
- Open Access
- 30 November 2020
- Published by MDPI AG in Nanomaterials
- Vol. 10 (12) , 2389
Facile One-Step Hydrothermal Synthesis of the rGO@Ni3V2O8 Interconnected Hollow Microspheres Composite for Lithium-Ion Batteries
Low-cost, vanadium-based mixed metal oxides mostly have a layered crystal structure with excellent kinetics for lithium-ion batteries, providing high energy density. The existence of multiple oxidation states and the coordination chemistry of vanadium require cost-effective, robust techniques to synthesize the scaling up of their morphology and surface properties. Hydrothermal synthesis is one of the most suitable techniques to achieve pure phase and multiple morphologies under various conditions of temperature and pressure. We attained a simple one-step hydrothermal approach to synthesize the reduced graphene oxide coated Nickel Vanadate (rGO@Ni3V2O8) composite with interconnected hollow microspheres. The self-assembly route produced microspheres, which were interconnected under hydrothermal treatment. Cyclic performance determined the initial discharge/charge capacities of 1209.76/839.85 mAh g−1 at the current density of 200 mA g−1 with a columbic efficiency of 69.42%, which improved to 99.64% after 100 cycles. High electrochemical performance was observed due to high surface area, the porous nature of the interconnected hollow microspheres, and rGO induction. These properties increased the contact area between electrode and electrolyte, the active surface of the electrodes, and enhanced electrolyte penetration, which improved Li-ion diffusivity and electronic conductivity.
- 30 November 2020
- Published by MDPI AG in Nanomaterials
- Vol. 10 (12) , 2389
Open AccessFacile One-Step Hydrothermal Synthesis of the rGO@Ni3V2O8 Interconnected Hollow Microspheres Composite for Lithium-Ion Batteries
Low-cost, vanadium-based mixed metal oxides mostly have a layered crystal structure with excellent kinetics for lithium-ion batteries, providing high energy density. The existence of multiple oxidation states and the coordination chemistry of vanadium require cost-effective, robust techniques to synthesize the scaling up of their morphology and surface properties. Hydrothermal synthesis is one of the most suitable techniques to achieve pure phase and multiple morphologies under various conditions of temperature and pressure. We attained a simple one-step hydrothermal approach to synthesize the reduced graphene oxide coated Nickel Vanadate (rGO@Ni3V2O8) composite with interconnected hollow microspheres. The self-assembly route produced microspheres, which were interconnected under hydrothermal treatment. Cyclic performance determined the initial discharge/charge capacities of 1209.76/839.85 mAh g−1 at the current density of 200 mA g−1 with a columbic efficiency of 69.42%, which improved to 99.64% after 100 cycles. High electrochemical performance was observed due to high surface area, the porous nature of the interconnected hollow microspheres, and rGO induction. These properties increased the contact area between electrode and electrolyte, the active surface of the electrodes, and enhanced electrolyte penetration, which improved Li-ion diffusivity and electronic conductivity.
- 1 November 2020
- Published by Hindawi Limited in International Journal of Energy Research
- Vol. 44 (14) , 11171-11184
Electrochemical performance ofMn3O4nanorodsby N-doped reduced graphene oxide using ultrasonic spray pyrolysis for lithium storage
The crumpled N-doped reduced graphene oxide wrapped Mn(3)O(4)nanorods (Mn-NrGO) composite are synthesized via a combination of spray pyrolysis and a hydrothermal process for lithium ion batteries. The Mn(3)O(4)nanorods are uniformly dispersed in the conductive matrix of crumpled N-doped reduced graphene oxide, forming a uniform wrapped composite and stopping them from restacking, which synergistically enhanced the Li(+)ion conductivity. The well-defined Mn(3)O(4)nanorods, strong interaction between Mn(3)O(4)and NrGO, and highly graphitic properties of Mn-NrGO result in superior reversible capacity, long cycle life, and superior rate performance of approximately 1500 mAh/g at 0.1 C after 100 cycles and >660S mAh/g at 1.0 C after 500 cycles.
- 1 November 2020
- Published by Hindawi Limited in International Journal of Energy Research
- Vol. 44 (14) , 11171-11184
Electrochemical performance ofMn3O4nanorodsby N-doped reduced graphene oxide using ultrasonic spray pyrolysis for lithium storage
The crumpled N-doped reduced graphene oxide wrapped Mn(3)O(4)nanorods (Mn-NrGO) composite are synthesized via a combination of spray pyrolysis and a hydrothermal process for lithium ion batteries. The Mn(3)O(4)nanorods are uniformly dispersed in the conductive matrix of crumpled N-doped reduced graphene oxide, forming a uniform wrapped composite and stopping them from restacking, which synergistically enhanced the Li(+)ion conductivity. The well-defined Mn(3)O(4)nanorods, strong interaction between Mn(3)O(4)and NrGO, and highly graphitic properties of Mn-NrGO result in superior reversible capacity, long cycle life, and superior rate performance of approximately 1500 mAh/g at 0.1 C after 100 cycles and >660S mAh/g at 1.0 C after 500 cycles.
- Open Access
- 13 January 2020
- Published by MDPI AG in Nanomaterials
- Vol. 10 (1) , 142
Intrinsic Control in Defects Density for Improved ZnO Nanorod-Based UV Sensor Performance
Hitherto, most research has primarily focused on improving the UV sensor efficiency via surface treatments and by stimulating the ZnO nanorod (ZNR) surface Schottky barriers. However, to the best of our knowledge, no study has yet probed the intrinsic crystal defect generation and its effects on UV sensor efficiency. In this study, we undertake this task by fabricating an intrinsic defect-prone hydrothermally grown ZNRs (S1), Ga-doped ZNRs (S2), and defect-free microwave-assisted grown ZNRs (S3). The defect states were recognized by studying X-ray diffraction and photoluminescence characteristics. The large number of crystal defects in S1 and S2 had two pronged disadvantages. (1) Most of the UV light was absorbed by the defect traps and the e–h pair generation was compromised. (2) Mobility was directly affected by the carrier–carrier scattering and phonon scattering processes. Hence, the overall UV sensor efficiency was compromised based on the defect-induced mobility-response model. Considering the facts, defect-free S3 exhibited the best UV sensor performance with the highest on/off ratio, the least impulse response time, the highest recombination time, and highest gain-induced responsivity to 368 nm UV light, which was desired of an efficient passive metal oxide-based UV sensor. Our results were compared with the recently published results.
- 13 January 2020
- Published by MDPI AG in Nanomaterials
- Vol. 10 (1) , 142
Open AccessIntrinsic Control in Defects Density for Improved ZnO Nanorod-Based UV Sensor Performance
Hitherto, most research has primarily focused on improving the UV sensor efficiency via surface treatments and by stimulating the ZnO nanorod (ZNR) surface Schottky barriers. However, to the best of our knowledge, no study has yet probed the intrinsic crystal defect generation and its effects on UV sensor efficiency. In this study, we undertake this task by fabricating an intrinsic defect-prone hydrothermally grown ZNRs (S1), Ga-doped ZNRs (S2), and defect-free microwave-assisted grown ZNRs (S3). The defect states were recognized by studying X-ray diffraction and photoluminescence characteristics. The large number of crystal defects in S1 and S2 had two pronged disadvantages. (1) Most of the UV light was absorbed by the defect traps and the e–h pair generation was compromised. (2) Mobility was directly affected by the carrier–carrier scattering and phonon scattering processes. Hence, the overall UV sensor efficiency was compromised based on the defect-induced mobility-response model. Considering the facts, defect-free S3 exhibited the best UV sensor performance with the highest on/off ratio, the least impulse response time, the highest recombination time, and highest gain-induced responsivity to 368 nm UV light, which was desired of an efficient passive metal oxide-based UV sensor. Our results were compared with the recently published results.