Dexue Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dexue Liu has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Qinglin Li
School of Material Science and Engineering, Lanzhou University of Technology, Lanzhou, China
2 shared publicationsShiwen Hu
State Key Laboratory of Advanced Processing and Recycling of Non-ferrous Metals, Lanzhou 730050, China; School of Material Science and Engineering, Lanzhou University of Technology, Lanzhou 730050, China
2 shared publicationsXiao Zhang
State Key Laboratory of Advanced Processing and Recycling of Non-ferrous Metals, Lanzhou University of Technology, Lanzhou, Gansu Province, China
2 shared publicationsXin Pang
Lanzhou University of Technology
2 shared publicationsXunyan Yin
State Key Laboratory of Advanced Processing and Recycling of Non-ferrous Metals, Lanzhou 730050, China; School of Material Science and Engineering, Lanzhou University of Technology, Lanzhou 730050, China
2 shared publicationsYutian Ding
Lanzhou University of Technology
2 shared publications
Latest Publications
- 1 December 2019
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 34 (6) , 1297-1308
Phase Transformation Strengthening of Hot Extruded Inconel 625 under High-temperature Load Environment
- 1 December 2019
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 34 (6) , 1297-1308
Phase Transformation Strengthening of Hot Extruded Inconel 625 under High-temperature Load Environment
- 26 October 2018
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 49 (11) , 1353-1363
Hot compression deformation behavior and processing map of Mg–Y–Sr–La(Ce)–Zr biodegradable magnesium alloy
The flow behavior of Mg–4.2Y–1.5Sr‐0.6La(Ce)–0.5Zr biodegradable magnesium alloy was investigated using Gleeble‐1500D thermal simulation test machine at deforming temperature of 350 °C–500 °C, strain rates of 0.001 s‐1–1 s‐1 and the final strain of 60 %. The flow stress constitutive relationship and processing map was established. Meanwhile, the experimental results indicated that flow stress of the Mg–Y–Sr–La(Ce)–Zr alloy increase and then decrease with increase of strain, which is due to work hardening caused by dislocation blocking and softening effects caused by dynamic recrystallization respectively. According to the processing maps and dynamic recrystallization of the alloy, the optimum processing parameters of the alloy are determined with a temperature range of 450 °C–500 °C and strain rate range of 0.006 s‐1–0.009 s‐1.
- 26 October 2018
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 49 (11) , 1353-1363
Hot compression deformation behavior and processing map of Mg–Y–Sr–La(Ce)–Zr biodegradable magnesium alloy
The flow behavior of Mg–4.2Y–1.5Sr‐0.6La(Ce)–0.5Zr biodegradable magnesium alloy was investigated using Gleeble‐1500D thermal simulation test machine at deforming temperature of 350 °C–500 °C, strain rates of 0.001 s‐1–1 s‐1 and the final strain of 60 %. The flow stress constitutive relationship and processing map was established. Meanwhile, the experimental results indicated that flow stress of the Mg–Y–Sr–La(Ce)–Zr alloy increase and then decrease with increase of strain, which is due to work hardening caused by dislocation blocking and softening effects caused by dynamic recrystallization respectively. According to the processing maps and dynamic recrystallization of the alloy, the optimum processing parameters of the alloy are determined with a temperature range of 450 °C–500 °C and strain rate range of 0.006 s‐1–0.009 s‐1.
- 1 March 2018
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 84, 263-270
Degradation mechanism of magnesium alloy stent under simulated human micro-stress environment
- 1 March 2018
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 84, 263-270
Degradation mechanism of magnesium alloy stent under simulated human micro-stress environment
- 1 September 2017
- Published by SAGE Publications in Materials Science and Technology
- Vol. 33 (14) , 1610-1617
High-temperature mechanical properties of Inconel-625: Role of carbides and delta phase
Based on the temperature sensitivity characteristics, high-temperature tensile tests were performed at different temperatures and after different solid solution treatments to investigate the effect of Cr-rich M23C6, Nb-rich MC and the delta phase on the mechanical properties of Inconel 625. The experimental results indicated that the Cr-rich M23C6 carbides and the Nb-rich MC carbides decomposed at 700°C, which could be the reason for resulting tensile strength anomaly that was observed in a narrow temperature range from 650 to 700°C during the tensile tests at different temperatures. For the samples subjected to a prior solid solution treatment, the size of the δ phase was found to increase with the solution treatment temperature, whereas the elongation at fracture decreased.
- 1 September 2017
- Published by SAGE Publications in Materials Science and Technology
- Vol. 33 (14) , 1610-1617
High-temperature mechanical properties of Inconel-625: Role of carbides and delta phase
Based on the temperature sensitivity characteristics, high-temperature tensile tests were performed at different temperatures and after different solid solution treatments to investigate the effect of Cr-rich M23C6, Nb-rich MC and the delta phase on the mechanical properties of Inconel 625. The experimental results indicated that the Cr-rich M23C6 carbides and the Nb-rich MC carbides decomposed at 700°C, which could be the reason for resulting tensile strength anomaly that was observed in a narrow temperature range from 650 to 700°C during the tensile tests at different temperatures. For the samples subjected to a prior solid solution treatment, the size of the δ phase was found to increase with the solution treatment temperature, whereas the elongation at fracture decreased.
- 2 August 2017
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 26 (8) , 3983-3992
Effects of Dy, Sr and Die Casting on Microstructure, Mechanical and Corrosion Properties of Mg-Dy-Sr-Nd-Zr Alloys
- 2 August 2017
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 26 (8) , 3983-3992
Effects of Dy, Sr and Die Casting on Microstructure, Mechanical and Corrosion Properties of Mg-Dy-Sr-Nd-Zr Alloys
- 21 December 2016
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 31 (6) , 1368-1376
Effects of heating and hot extrusion process on microstructure and properties of inconel 625 alloy
- 21 December 2016
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 31 (6) , 1368-1376
Effects of heating and hot extrusion process on microstructure and properties of inconel 625 alloy
- 6 December 2016
- Published by Wiley in Advanced Engineering Materials
- Vol. 19 (3)
Microstructural Evolution and Properties of a Hot Extruded and HPT‐Processed Resorbable Magnesium WE43 Alloy
Disks of an extruded magnesium WE43 alloy are processed by high‐pressure torsion (HPT) and the evolutions of microstructure and mechanical properties are investigated in detail. Excellent grain refinement is achieved by HPT processing with a reduction in grain size from an initial value of ≈12 μm to a final value of ≈200–300 nm after 10 turns. The microhardness increases significantly with HPT processing but low hardness values are recorded at the centers of the disks. The tensile strength initially increases and then decreases while the elongation decreases. Observations of the fracture surfaces reveal a corresponding transition of the fracture mode from ductile to brittle.
- 6 December 2016
- Published by Wiley in Advanced Engineering Materials
- Vol. 19 (3)
Microstructural Evolution and Properties of a Hot Extruded and HPT‐Processed Resorbable Magnesium WE43 Alloy
Disks of an extruded magnesium WE43 alloy are processed by high‐pressure torsion (HPT) and the evolutions of microstructure and mechanical properties are investigated in detail. Excellent grain refinement is achieved by HPT processing with a reduction in grain size from an initial value of ≈12 μm to a final value of ≈200–300 nm after 10 turns. The microhardness increases significantly with HPT processing but low hardness values are recorded at the centers of the disks. The tensile strength initially increases and then decreases while the elongation decreases. Observations of the fracture surfaces reveal a corresponding transition of the fracture mode from ductile to brittle.