Davood Efhamisisi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Davood Efhamisisi has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Asghar Tarmian
Department of Wood and Paper Science and Technology, Faculty of Natural Resources, University of Tehran, Karaj, Iran
3 shared publicationsMarie-France Thevenon
BioWooEB
2 shared publications- Reza Oladi
Department of Wood and Paper Science and Technology, Faculty of Natural Resources, University College of Agriculture and Natural Resources, University of Tehran, Karaj, Iran
2 shared publications Yahya Hamzeh
Department of Wood and Paper Sciences and Technology, Faculty of Natural Resources University of Tehran Karaj Iran
2 shared publicationsAkbar Mastouri
1 shared publication- Akbar Mastouri
Department of Wood and Paper Science and Technology, Faculty of Natural Resources, University of Tehran, Karaj, Iran
1 shared publication
Latest Publications
- 1 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Preservation of plywood against biological attack with low environmental impact using tannin-boron preservative
Protection à faible impact environnemental des contreplaqués avec des associations tannins-bore: Une étude expérimentale a été menée afin de protéger des attaques biologiques des contreplaqués faits d'essences non durables (hêtre et peuplier), et ce, avec un faible impact environnemental. Des produits de protection à base de tannins et de bore, nouvellement développés afin de réduire le lessivage du bore, ont été sélectionnés pour ce but. Ce système a été utilisé pour protéger les contreplaqués selon deux approches : (1) au niveau de la colle pour remplacer les adhésives à base de formaldéhyde et coller les plis, (2) en traitement des plis avec des formulations plus diluées, les plis étant collés avec des adhésifs mélamine-urée-formaldéhyde. Les données expérimentales de cette thèse peuvent être classées en trois grands groupes : essais chimiques et thermomécaniques des colles tannin-bore, mesure des propriétés physiques et mécaniques, de la résistance biologique avant et après vieillissement des différents panneaux. Les essais chimiques sur les colles tannin/hexamine ont montré que l'addition de bore sous forme d'acide borique peut contribuer à plus de liaisons inter-flavonoids et à ouvrir les cycles pyranes ce qui accélère les réactions de polymérisation. Des analyses thermomécaniques sur les colles contenant des tannins de mimosa et de quebracho ont confirmé que l'addition d'acide borique (1) abaissait le temps et la température de prise, et (2) augmentait les valeurs du module d'élasticité de la colle. L'addition d'une quantité optimale d'acide borique dans la colle à base de tannin augmente les propriétés physiques et la résistance au cisaillement. Une charge excessive d'acide borique (10%) dans la colle est la cause de pertes de propriétés mécaniques et physiques. Bien qu'en faible quantité, l'introduction de l'acide borique dans la colle de tannin amène une protection efficace contre l'attaque fongique, même après un lessivage selon l'EN 1250-2. Les résultats des essais termites montrent que l'acide borique contenu dans la colle cause le plus faible taux de survie des insectes et de perte de masse, mais présentent un fort degré d'attaque selon une cotation visuelle. Aucune amélioration n'a été obtenue lors d'un essai de choix après lessivage. Les contreplaqués faits de plis traités par des solutions tannin-bore ont montré des résistances au cisaillement plus faibles, mais toujours dans les gammes requises pour des applications en atmosphère humide. Des résultats satisfaisants ont été obtenus par les réseaux polymères de tannins, même après une lessivage sévère, vis-à-vis de l'attaque fongique. Les contreplaqués faits de plis traités à l'acide borique seul ont présenté une sensibilité importante à l'attaque biologique après un lessivage. Les résultats des essais termites ont montré un faible taux de survie des insectes et de perte de masse, même après un lessivage sévère, pour les contreplaqués avec des plis traités par des systèmes tannin-bore. Les résultats d'un essai de choix a montré que les termites préféraient se nourrir des témoins quand l'alternative proposée était des échantillons traités avec des systèmes tannin-bore.
- 1 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Preservation of plywood against biological attack with low environmental impact using tannin-boron preservative
Protection à faible impact environnemental des contreplaqués avec des associations tannins-bore: Une étude expérimentale a été menée afin de protéger des attaques biologiques des contreplaqués faits d'essences non durables (hêtre et peuplier), et ce, avec un faible impact environnemental. Des produits de protection à base de tannins et de bore, nouvellement développés afin de réduire le lessivage du bore, ont été sélectionnés pour ce but. Ce système a été utilisé pour protéger les contreplaqués selon deux approches : (1) au niveau de la colle pour remplacer les adhésives à base de formaldéhyde et coller les plis, (2) en traitement des plis avec des formulations plus diluées, les plis étant collés avec des adhésifs mélamine-urée-formaldéhyde. Les données expérimentales de cette thèse peuvent être classées en trois grands groupes : essais chimiques et thermomécaniques des colles tannin-bore, mesure des propriétés physiques et mécaniques, de la résistance biologique avant et après vieillissement des différents panneaux. Les essais chimiques sur les colles tannin/hexamine ont montré que l'addition de bore sous forme d'acide borique peut contribuer à plus de liaisons inter-flavonoids et à ouvrir les cycles pyranes ce qui accélère les réactions de polymérisation. Des analyses thermomécaniques sur les colles contenant des tannins de mimosa et de quebracho ont confirmé que l'addition d'acide borique (1) abaissait le temps et la température de prise, et (2) augmentait les valeurs du module d'élasticité de la colle. L'addition d'une quantité optimale d'acide borique dans la colle à base de tannin augmente les propriétés physiques et la résistance au cisaillement. Une charge excessive d'acide borique (10%) dans la colle est la cause de pertes de propriétés mécaniques et physiques. Bien qu'en faible quantité, l'introduction de l'acide borique dans la colle de tannin amène une protection efficace contre l'attaque fongique, même après un lessivage selon l'EN 1250-2. Les résultats des essais termites montrent que l'acide borique contenu dans la colle cause le plus faible taux de survie des insectes et de perte de masse, mais présentent un fort degré d'attaque selon une cotation visuelle. Aucune amélioration n'a été obtenue lors d'un essai de choix après lessivage. Les contreplaqués faits de plis traités par des solutions tannin-bore ont montré des résistances au cisaillement plus faibles, mais toujours dans les gammes requises pour des applications en atmosphère humide. Des résultats satisfaisants ont été obtenus par les réseaux polymères de tannins, même après une lessivage sévère, vis-à-vis de l'attaque fongique. Les contreplaqués faits de plis traités à l'acide borique seul ont présenté une sensibilité importante à l'attaque biologique après un lessivage. Les résultats des essais termites ont montré un faible taux de survie des insectes et de perte de masse, même après un lessivage sévère, pour les contreplaqués avec des plis traités par des systèmes tannin-bore. Les résultats d'un essai de choix a montré que les termites préféraient se nourrir des témoins quand l'alternative proposée était des échantillons traités avec des systèmes tannin-bore.
- Open Access
- 6 August 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-15
Silanes for conservation of archaeological woods using modeled birch wood: antifungal, physical-chemical and TGA studies
Conservation of ancient wooden artifacts, in addition to consolidation advantage, prevent its deterioration over time. In this research, silane consolidants, including methyltrimethoxysilane (MTMS) and 3-mercaptopropyltrimethoxysilane (MPTMS) with 25 wt% in ethanol were applied under controlled conditions on modeled birch wood (Betula pendula) as a conservation strategy for archeological woods in terrestrial environments. While the wood samples were gradually saturated and dried, aesthetics and cell-walls integrity were also considered. The leaching characteristics, visual and physical changes of wood specimens were evaluated during 4 aging periods to assess their performance and stability. Morphological and chemical reactions were analyzed by FE-SEM microscopy and ATR-FTIR spectroscopy, respectively. For comparison, antifungal properties and thermogravimetric analysis (TGA, DTG) were also examined on the samples. As results, silanization reduced the wood-water interactions while maintaining the aesthetic properties, especially with MPTMS. Maximum water-repellency of silane-treated woods were achieved after a water post-treatment, which probably indicates the secondary hydrolysis of silanes in the presence of water and their re-polymerization. Biological-durability testing (according to EN 113-2) of birch wood (not-durable), against Basidiomycete fungi (i.e., Trametes versicolor and Gloeophyllum trabeum) showed ~ 90% (very-durable) and ~ 65% (moderately-durable) efficiency for MPTMS- and MTMS-treated wood respectively. Based on FTIR and TGA analysis, more interactions of MPTMS with lignin was found, which is more consistent with the chemical nature of most archaeological woods. Thermal-stability and low hygroscopicity of silane-reinforced woods were also confirmed by TGA/DTG, indicating high conservation potential of silanes for historical woods. Meanwhile, a complementary study on real ancient samples is recommended.
- 6 August 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-15
Open AccessSilanes for conservation of archaeological woods using modeled birch wood: antifungal, physical-chemical and TGA studies
Conservation of ancient wooden artifacts, in addition to consolidation advantage, prevent its deterioration over time. In this research, silane consolidants, including methyltrimethoxysilane (MTMS) and 3-mercaptopropyltrimethoxysilane (MPTMS) with 25 wt% in ethanol were applied under controlled conditions on modeled birch wood (Betula pendula) as a conservation strategy for archeological woods in terrestrial environments. While the wood samples were gradually saturated and dried, aesthetics and cell-walls integrity were also considered. The leaching characteristics, visual and physical changes of wood specimens were evaluated during 4 aging periods to assess their performance and stability. Morphological and chemical reactions were analyzed by FE-SEM microscopy and ATR-FTIR spectroscopy, respectively. For comparison, antifungal properties and thermogravimetric analysis (TGA, DTG) were also examined on the samples. As results, silanization reduced the wood-water interactions while maintaining the aesthetic properties, especially with MPTMS. Maximum water-repellency of silane-treated woods were achieved after a water post-treatment, which probably indicates the secondary hydrolysis of silanes in the presence of water and their re-polymerization. Biological-durability testing (according to EN 113-2) of birch wood (not-durable), against Basidiomycete fungi (i.e., Trametes versicolor and Gloeophyllum trabeum) showed ~ 90% (very-durable) and ~ 65% (moderately-durable) efficiency for MPTMS- and MTMS-treated wood respectively. Based on FTIR and TGA analysis, more interactions of MPTMS with lignin was found, which is more consistent with the chemical nature of most archaeological woods. Thermal-stability and low hygroscopicity of silane-reinforced woods were also confirmed by TGA/DTG, indicating high conservation potential of silanes for historical woods. Meanwhile, a complementary study on real ancient samples is recommended.
- Open Access
- 1 January 2024
- Published by Tech Science Press in Journal of Renewable Materials
- Vol. 12 (10) , 1715-1728
Chemically Modified Sugarcane Bagasse for Innovative Bio-Composites. Part One: Production and Physico-Mechanical Properties
Sugarcane bagasse is an agro-waste that could replace timber resources for the production of bio-composites. Composite boards such as particleboard offer an issue for the use and recycling of poor quality timber, and these engineered products can overcome some solid wood limitations such as heterogeneity and dimension. Bagasse offers an alternative to wood chips for particleboard production but present some disadvantages as well, such as poor physico-mechanical properties. To address these issues, bagasse fibers were treated with an innovative natural resin formulated with tannin and furfural. Impregnated particles with different concentrations of resin (5%, 10%, and 15% m/m) were exposed to temperatures of 40°C, 60°C, 80°C, and 100°C for resin curing. Various types of tannin-based adhesives, including tannin formaldehyde, tannin/formaldehyde-furfural, and tannin hexamine, were utilized for bonding the treated bagasse particles. The resultant panels were assessed for their physical and mechanical properties and compared to those produced using Melamine-Urea-Formaldehyde (MUF) adhesive. The density of the panels varied from 650 to 730 kg/m3 depending on the resin concentration. The values for both modulus of elasticity and modulus of rupture increased as the resin concentration increased. The internal bonding values exhibited an increase with resin concentration up to a critical point, after which a decreasing trend was observed. The water absorption and thickness swelling were significantly reduced with an increase in resin concentration. However, the panels produced using MUF adhesive yielded the most favorable physico-mechanical properties. Additionally, the panels made with tannin-based adhesives met the minimum requirements specified in the standard EN 312 (specifications for uncoated resin-bonded particleboards) for application in dry conditions. The analysis of formaldehyde emissions indicated that panels produced with tannin-based adhesives exhibited significantly lower emissions compared to those made with MUF. The tannin/furfural resin showed great potential for improving the quality of bagasse particleboard using tannin-based adhesives.
- 1 January 2024
- Published by Tech Science Press in Journal of Renewable Materials
- Vol. 12 (10) , 1715-1728
Open AccessChemically Modified Sugarcane Bagasse for Innovative Bio-Composites. Part One: Production and Physico-Mechanical Properties
Sugarcane bagasse is an agro-waste that could replace timber resources for the production of bio-composites. Composite boards such as particleboard offer an issue for the use and recycling of poor quality timber, and these engineered products can overcome some solid wood limitations such as heterogeneity and dimension. Bagasse offers an alternative to wood chips for particleboard production but present some disadvantages as well, such as poor physico-mechanical properties. To address these issues, bagasse fibers were treated with an innovative natural resin formulated with tannin and furfural. Impregnated particles with different concentrations of resin (5%, 10%, and 15% m/m) were exposed to temperatures of 40°C, 60°C, 80°C, and 100°C for resin curing. Various types of tannin-based adhesives, including tannin formaldehyde, tannin/formaldehyde-furfural, and tannin hexamine, were utilized for bonding the treated bagasse particles. The resultant panels were assessed for their physical and mechanical properties and compared to those produced using Melamine-Urea-Formaldehyde (MUF) adhesive. The density of the panels varied from 650 to 730 kg/m3 depending on the resin concentration. The values for both modulus of elasticity and modulus of rupture increased as the resin concentration increased. The internal bonding values exhibited an increase with resin concentration up to a critical point, after which a decreasing trend was observed. The water absorption and thickness swelling were significantly reduced with an increase in resin concentration. However, the panels produced using MUF adhesive yielded the most favorable physico-mechanical properties. Additionally, the panels made with tannin-based adhesives met the minimum requirements specified in the standard EN 312 (specifications for uncoated resin-bonded particleboards) for application in dry conditions. The analysis of formaldehyde emissions indicated that panels produced with tannin-based adhesives exhibited significantly lower emissions compared to those made with MUF. The tannin/furfural resin showed great potential for improving the quality of bagasse particleboard using tannin-based adhesives.
- 1 November 2021
- Published by Elsevier in Journal of Building Engineering
- Vol. 43
Physicochemical properties of thermally treated poplar wood in silicone and rapeseed oils: A comparative study
- 1 November 2021
- Published by Elsevier in Journal of Building Engineering
- Vol. 43
Physicochemical properties of thermally treated poplar wood in silicone and rapeseed oils: A comparative study
- 9 September 2021
- Published by BioResources in BioResources
- Vol. 16 (4) , 7138-7159
Furfural-based resin for modifying birch wood properties
Furfural (F) cannot be easily polymerized like furfuryl alcohol, but it is an aldehyde that can react with urea (U) to make a polymeric network. The possibility of preparing F/U polymer along with an acidic catalyzer (maleic anhydride; M) was evaluated as a means to improve some selected properties of birch (Betula pendula) wood. The F+U/M resin was introduced into the wood with a double treatment technology. The first step involved dilution of F in water and methanol, and the second step was immersion in a U/M aqueous solution. The color of treated wood was darkened after resin curing from brown to a spectrum of black depending on the amount of loaded resin. The 60 to 80% of materials were converted to a non-leachable polymer based on the different formulations. The water absorption and volumetric swelling of the treated samples decreased with an increase in weight percent gain (WPG). The analysis of mechanical strength showed that treatment with F + U/M reduced to some extent the hardness and the impact bending of wood, while modulus of rupture, modulus of elasticity, and compression parallel to the grain with WPG were increased. The exposure of the samples to the accelerated weathering showed noticeable changes in color and roughness.
- 9 September 2021
- Published by BioResources in BioResources
- Vol. 16 (4) , 7138-7159
Furfural-based resin for modifying birch wood properties
Furfural (F) cannot be easily polymerized like furfuryl alcohol, but it is an aldehyde that can react with urea (U) to make a polymeric network. The possibility of preparing F/U polymer along with an acidic catalyzer (maleic anhydride; M) was evaluated as a means to improve some selected properties of birch (Betula pendula) wood. The F+U/M resin was introduced into the wood with a double treatment technology. The first step involved dilution of F in water and methanol, and the second step was immersion in a U/M aqueous solution. The color of treated wood was darkened after resin curing from brown to a spectrum of black depending on the amount of loaded resin. The 60 to 80% of materials were converted to a non-leachable polymer based on the different formulations. The water absorption and volumetric swelling of the treated samples decreased with an increase in weight percent gain (WPG). The analysis of mechanical strength showed that treatment with F + U/M reduced to some extent the hardness and the impact bending of wood, while modulus of rupture, modulus of elasticity, and compression parallel to the grain with WPG were increased. The exposure of the samples to the accelerated weathering showed noticeable changes in color and roughness.
- 25 September 2020
- Published by Wiley in Biofuels, Bioproducts and Biorefining
- Vol. 15 (1) , 74-84
Pyrolysis acid as sustainable wood preservative against rot fungi
The use of pyrolysis acid (PA) as a liquid by‐product of the slow pyrolysis of wood or any other lignocellulosic biomass has been widely developed in agriculture for a variety of purposes such as crop enhancement or as a pesticide. Evidence from the literature suggests that PA could be used as a sustainable wood preservative to protect against rot fungi and termites. The experimental work presented here provides one of the first investigations into the anti‐decay efficiency of PA. Crude PA acid acquired from three different types of wood at two different temperature ranges (180–280 °C and 280–350 °C) was used to impregnate beech and pine wood samples in a full‐cell process. Then, the resistance of treated samples against white and brown rot fungi was evaluated (in accordance with European standard EN 113), before and after a leaching test (European standard EN 84). It was found that, generally, higher retention of chemicals inside the wood was observed with PA obtained at 350 °C (PA‐350). The leaching rate of chemicals from the treated samples with PA obtained at 280 °C (PA‐280) was significantly higher than from those treated with PA‐350. Before leaching, no statistical difference was observed among the impregnated woods in terms of decay resistance. Although the samples treated with PA‐280 initially showed fairly good decay resistance they partially lost it after leaching. This was particularly the case with brown rot. However, the impregnation of wood samples with PA‐350 met the requirements of EN 113 as an efficient treatment against basidiomycete fungi. © 2020 Society of Chemical Industry and John Wiley & Sons, Ltd
- 25 September 2020
- Published by Wiley in Biofuels, Bioproducts and Biorefining
- Vol. 15 (1) , 74-84
Pyrolysis acid as sustainable wood preservative against rot fungi
The use of pyrolysis acid (PA) as a liquid by‐product of the slow pyrolysis of wood or any other lignocellulosic biomass has been widely developed in agriculture for a variety of purposes such as crop enhancement or as a pesticide. Evidence from the literature suggests that PA could be used as a sustainable wood preservative to protect against rot fungi and termites. The experimental work presented here provides one of the first investigations into the anti‐decay efficiency of PA. Crude PA acid acquired from three different types of wood at two different temperature ranges (180–280 °C and 280–350 °C) was used to impregnate beech and pine wood samples in a full‐cell process. Then, the resistance of treated samples against white and brown rot fungi was evaluated (in accordance with European standard EN 113), before and after a leaching test (European standard EN 84). It was found that, generally, higher retention of chemicals inside the wood was observed with PA obtained at 350 °C (PA‐350). The leaching rate of chemicals from the treated samples with PA obtained at 280 °C (PA‐280) was significantly higher than from those treated with PA‐350. Before leaching, no statistical difference was observed among the impregnated woods in terms of decay resistance. Although the samples treated with PA‐280 initially showed fairly good decay resistance they partially lost it after leaching. This was particularly the case with brown rot. However, the impregnation of wood samples with PA‐350 met the requirements of EN 113 as an efficient treatment against basidiomycete fungi. © 2020 Society of Chemical Industry and John Wiley & Sons, Ltd
- 15 December 2016
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 71 (3) , 249-258
Tannin-boron complex as a preservative for 3-ply beech plywoods designed for humid conditions
Boric acid (BA) effectively controls wood-rotting fungi and termite attack but is readily leached out in outdoor exposure. A newly developed tannin-boron (TB) complex has been investigated to reduce BA leaching and to preserve beech plywood from biological attack. Wood veneers were impregnated with different TB solutions and then bonded with a melamine urea formaldehyde (MUF) adhesive for bond class 2 applications. The formation of a solid hydrophobic TB network on the veneer surfaces partially decreased the tensile shear strength of plywood but the prepared panels met the requirements for bond class 2. The plywood samples made from veneers treated with only BA solutions showed fair resistance against white rot fungus and termite attack, but the durability decreased even after mild leaching tests. The panels made of treated veneers with TB formulations showed instead a high resistance against biological attack after mild leaching and to some extent after severe leaching tests. This depended on the concentration of tannin and BA in the solutions. Favorable results were obtained with 20% tannin in the formulation. The results of the termites feeding choice test were more positive than those obtained by a forced feeding test. The control samples were attacked faster and showed higher weight loss when alternative samples included TB formulations.
- 15 December 2016
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 71 (3) , 249-258
Tannin-boron complex as a preservative for 3-ply beech plywoods designed for humid conditions
Boric acid (BA) effectively controls wood-rotting fungi and termite attack but is readily leached out in outdoor exposure. A newly developed tannin-boron (TB) complex has been investigated to reduce BA leaching and to preserve beech plywood from biological attack. Wood veneers were impregnated with different TB solutions and then bonded with a melamine urea formaldehyde (MUF) adhesive for bond class 2 applications. The formation of a solid hydrophobic TB network on the veneer surfaces partially decreased the tensile shear strength of plywood but the prepared panels met the requirements for bond class 2. The plywood samples made from veneers treated with only BA solutions showed fair resistance against white rot fungus and termite attack, but the durability decreased even after mild leaching tests. The panels made of treated veneers with TB formulations showed instead a high resistance against biological attack after mild leaching and to some extent after severe leaching tests. This depended on the concentration of tannin and BA in the solutions. Favorable results were obtained with 20% tannin in the formulation. The results of the termites feeding choice test were more positive than those obtained by a forced feeding test. The control samples were attacked faster and showed higher weight loss when alternative samples included TB formulations.