Weihui Jiang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Weihui Jiang has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
Jianmin Liu
National Engineering Research Centre for Domestic & Building Ceramics, Jingdezhen Ceramic Institute, Jingdezhen, People’s Republic of China
6 shared publicationsLifeng Miao
National Engineering Research Centre for Domestic & Building Ceramics, Jingdezhen Ceramic Institute, Jingdezhen, People’s Republic of China
6 shared publications- Guo Feng
Jingdezhen Ceramic University
5 shared publications Qian Wu
National Engineering Research Centre for Domestic & Building Ceramics, Jingdezhen Ceramic Institute, Jingdezhen, People’s Republic of China
5 shared publicationsFeng Jiang
National Engineering Research Center for Domestic and Building Ceramics, Jingdezhen, Jiangxi, China
4 shared publicationsTao Wang
School of Material Science and Engineering, Jingdezhen Ceramic University, Jingdezhen, Jiangxi, China
4 shared publications
Latest Publications
- 12 January 2023
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 34 (2) , 1-9
V-doping-induced oxygen vacancy in WO3 inverse opal film for improved electrochromic response in NIR region
- 12 January 2023
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 34 (2) , 1-9
V-doping-induced oxygen vacancy in WO3 inverse opal film for improved electrochromic response in NIR region
- Open Access
- 1 January 2023
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 17 (2) , 140-148
Low temperature synthesis of NaSICON NaZr2(PO4)3 powders with the assistance of in situ formed mineralizer
A new approach was developed to prepare NaZr2(PO4)3 (NZP) powders at low temperature of 330?C. The effect of different molar ratios of ZrO(NO3)2 ? xH2O to NaH2PO4 ? 2H2O on the synthesis of NZP powders was systematically investigated by XRD, FE-SEM, TEM, EDS and Raman spectroscopy. The mineralizer NaNO3 was formed in situ due to the mechanochemical reaction between raw materials ZrO(NO3)2 ? xH2O and NaH2PO4 ? 2H2O during the grinding process. When the optimal molar ratio of Zr:P = 2:6 was used, the NZP powders with high crystallinity, good dispersity and particle sizes in the range of 500-700 nm were obtained. The dense NZP ceramics was obtained by sintering at 1100 ?C for 3 h with 2 wt.% ZnO as the sintering aid. The relative density and Vickers hardness of the sintered ceramics reached 93.4% and 704MPa, respectively.
- 1 January 2023
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 17 (2) , 140-148
Open AccessLow temperature synthesis of NaSICON NaZr2(PO4)3 powders with the assistance of in situ formed mineralizer
A new approach was developed to prepare NaZr2(PO4)3 (NZP) powders at low temperature of 330?C. The effect of different molar ratios of ZrO(NO3)2 ? xH2O to NaH2PO4 ? 2H2O on the synthesis of NZP powders was systematically investigated by XRD, FE-SEM, TEM, EDS and Raman spectroscopy. The mineralizer NaNO3 was formed in situ due to the mechanochemical reaction between raw materials ZrO(NO3)2 ? xH2O and NaH2PO4 ? 2H2O during the grinding process. When the optimal molar ratio of Zr:P = 2:6 was used, the NZP powders with high crystallinity, good dispersity and particle sizes in the range of 500-700 nm were obtained. The dense NZP ceramics was obtained by sintering at 1100 ?C for 3 h with 2 wt.% ZnO as the sintering aid. The relative density and Vickers hardness of the sintered ceramics reached 93.4% and 704MPa, respectively.
- Open Access
Two-Dimensional V2O5 Inverse Opal: Fabrication and Electrochromic Application
The open-layered structure of Vanadium pentoxide (V2O5) has triggered significant interest in exploring its energy-related application as lithium (Li) intercalation cathode material. Various methods are extensively studied to improve the Li diffusion using thin films or nanoarchitecture. In this work, high-quality two-dimensional (2D) inverse opal α-V2O5 films were synthesized via a modified ‘dynamic hard template’ infiltration strategy using sacrificial polystyrene spheres (PS, a diameter of 530 nm) photonic crystal as a template. The new material exhibited an excellent porous array with featured structural colors in a large area. The electrochromic behavior was explored by combining bandgap and electrochemical characterization. On the one hand, the intercalation/deintercalation of Li+ played an important role in the bandgap (Eg), and thereafter on the visible range transmittance through changing the film’s stoichiometry and the valence of vanadium ions. On the other hand, the asymmetry of the lattice due to the disordered distribution of Li+ within the V2O5 interlayer and/or the formation of an irreversible phase explained the change in transmittance with voltage.
Open AccessTwo-Dimensional V2O5 Inverse Opal: Fabrication and Electrochromic Application
The open-layered structure of Vanadium pentoxide (V2O5) has triggered significant interest in exploring its energy-related application as lithium (Li) intercalation cathode material. Various methods are extensively studied to improve the Li diffusion using thin films or nanoarchitecture. In this work, high-quality two-dimensional (2D) inverse opal α-V2O5 films were synthesized via a modified ‘dynamic hard template’ infiltration strategy using sacrificial polystyrene spheres (PS, a diameter of 530 nm) photonic crystal as a template. The new material exhibited an excellent porous array with featured structural colors in a large area. The electrochromic behavior was explored by combining bandgap and electrochemical characterization. On the one hand, the intercalation/deintercalation of Li+ played an important role in the bandgap (Eg), and thereafter on the visible range transmittance through changing the film’s stoichiometry and the valence of vanadium ions. On the other hand, the asymmetry of the lattice due to the disordered distribution of Li+ within the V2O5 interlayer and/or the formation of an irreversible phase explained the change in transmittance with voltage.
- Open Access
- 1 January 2021
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 15 (3) , 314-318
Novel yellow to blackish green Ni-doped aluminium titanate ceramic pigments
Novel yellow to blackish green Ni-doped aluminium titanate (Al2TiO5) ceramic pigments were synthesized by solid-state reaction method at 1400 ?C. Effects of nickel doping content on phase composition, microstructure, optical properties and stability were studied. The results show that the higher content of Al2TiO5 phase and the reduction of the lattice distortion of aluminium titanate could be attributed to the entry of nickel ions into aluminium titanate lattice resulting in the formation of solid solution. Ni-doped aluminium titanate ceramic pigments show exceptional glaze colouring and are expected to be promising high-temperature pigments.
- 1 January 2021
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 15 (3) , 314-318
Open AccessNovel yellow to blackish green Ni-doped aluminium titanate ceramic pigments
Novel yellow to blackish green Ni-doped aluminium titanate (Al2TiO5) ceramic pigments were synthesized by solid-state reaction method at 1400 ?C. Effects of nickel doping content on phase composition, microstructure, optical properties and stability were studied. The results show that the higher content of Al2TiO5 phase and the reduction of the lattice distortion of aluminium titanate could be attributed to the entry of nickel ions into aluminium titanate lattice resulting in the formation of solid solution. Ni-doped aluminium titanate ceramic pigments show exceptional glaze colouring and are expected to be promising high-temperature pigments.
- Open Access
- 1 January 2021
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 15 (3) , 219-225
Facile preparation of ZrO2 whiskers by LiF-KCl molten salts synthesis
Monoclinic zirconia (ZrO2) whiskers were made via the molten salt method using zirconyl chloride octahydrate (ZrOCl2 ? 8H2O) as zirconium source, potassium chloride (KCl) as molten salt and lithium fluoride (LiF) as a mineraliser. DSC-TG, XRD, FE-SEM, Raman and TEM were performed to study the effects of heat treatment temperature, holding time and heating rate on the synthesis of zirconia whiskers. The results indicate that zirconia whiskers with diameters of 50-80 nm and aspect ratios of 10-30 can be obtained by heating the precursor at slow rate (3?C/min) to 718?C for 1 h and then at faster rate (7?C/min) to 950?C for 3 h. The whiskers have a smooth surface and grow in [001] direction. The key to the ZrO2 whiskers growth is the controlled dissolution and precipitation of the ZrO2 in a LiF-KCl molten salt solution environment.
- 1 January 2021
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 15 (3) , 219-225
Open AccessFacile preparation of ZrO2 whiskers by LiF-KCl molten salts synthesis
Monoclinic zirconia (ZrO2) whiskers were made via the molten salt method using zirconyl chloride octahydrate (ZrOCl2 ? 8H2O) as zirconium source, potassium chloride (KCl) as molten salt and lithium fluoride (LiF) as a mineraliser. DSC-TG, XRD, FE-SEM, Raman and TEM were performed to study the effects of heat treatment temperature, holding time and heating rate on the synthesis of zirconia whiskers. The results indicate that zirconia whiskers with diameters of 50-80 nm and aspect ratios of 10-30 can be obtained by heating the precursor at slow rate (3?C/min) to 718?C for 1 h and then at faster rate (7?C/min) to 950?C for 3 h. The whiskers have a smooth surface and grow in [001] direction. The key to the ZrO2 whiskers growth is the controlled dissolution and precipitation of the ZrO2 in a LiF-KCl molten salt solution environment.
- 13 June 2020
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 17 (5) , 2147-2155
Effects of aggregate/matrix‐phase ratio on the in‐situ synthesis of SiC whiskers and properties of reaction‐bonded SiC
Reaction‐bonded silicon carbide (RBSC) materials were synthesized by a carbon‐buried firing method, using α‐SiC powders with different sizes as aggregates, while silicon and graphite powders as matrix‐phase materials for in‐situ synthesis of β‐SiC. The effect of the mass ratio of α‐SiC aggregate to β‐SiC matrix‐phase on the in‐situ synthesis of β‐SiC whiskers was investigated and the optimum mass ratio was determined according to the properties of RBSC materials. The phase compositions, microstructure, and properties of the RBSC materials were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscope (TEM), respectively. The results showed that the decreasing aggregate/matrix‐phase ratio could increase the yield and aspect ratio of β‐SiC whiskers by improving the amount of pores and SiO 2 content. The β‐SiC whiskers with stacking faults grew along [111] direction. The in‐situ formed β‐SiC whiskers and SiO 2 in the matrix‐phase enhanced the hot modulus of rupture (HMOR) of the RBSC materials, and the sample with the aggregate/matrix‐phase ratio of 70:30 showed the highest cold modulus of rupture (CMOR) of 53.3 MPa, high HMOR of 43.3 MPa, and medium water absorption of 13.8%.
- 13 June 2020
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 17 (5) , 2147-2155
Effects of aggregate/matrix‐phase ratio on the in‐situ synthesis of SiC whiskers and properties of reaction‐bonded SiC
Reaction‐bonded silicon carbide (RBSC) materials were synthesized by a carbon‐buried firing method, using α‐SiC powders with different sizes as aggregates, while silicon and graphite powders as matrix‐phase materials for in‐situ synthesis of β‐SiC. The effect of the mass ratio of α‐SiC aggregate to β‐SiC matrix‐phase on the in‐situ synthesis of β‐SiC whiskers was investigated and the optimum mass ratio was determined according to the properties of RBSC materials. The phase compositions, microstructure, and properties of the RBSC materials were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscope (TEM), respectively. The results showed that the decreasing aggregate/matrix‐phase ratio could increase the yield and aspect ratio of β‐SiC whiskers by improving the amount of pores and SiO 2 content. The β‐SiC whiskers with stacking faults grew along [111] direction. The in‐situ formed β‐SiC whiskers and SiO 2 in the matrix‐phase enhanced the hot modulus of rupture (HMOR) of the RBSC materials, and the sample with the aggregate/matrix‐phase ratio of 70:30 showed the highest cold modulus of rupture (CMOR) of 53.3 MPa, high HMOR of 43.3 MPa, and medium water absorption of 13.8%.
- Open Access
- 1 January 2019
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 13 (3) , 229-234
Preparation, characterization and formation mechanism of single-crystal zirconia micro-sheets
Zirconia micro-sheets were prepared by molten salt method using the salt mixture of NaCl and NaF. FE-SEM, TEM, EDS, DTA-TG, XRD, Raman and FT-IR techniques were employed to characterize the morphology, phase composition and formation mechanism of the ZrO2 micro-sheets. The obtained monoclinic ZrO2 microsheets with exposed {100} facets show an average thickness of 0.2 ?m. The growth of the ZrO2 micro-sheets is proved to be assisted by the addition of fluoride. On the one hand, the addition of fluoride promotes the mass transfer of zirconia through the formation of zirconium fluoride complexes (ZrF 3-7). On the other hand, fluoride adsorbed on the surface of zirconia stabilizes {100} facets and lead to the exposure of {100} facets in the final product.
- 1 January 2019
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 13 (3) , 229-234
Open AccessPreparation, characterization and formation mechanism of single-crystal zirconia micro-sheets
Zirconia micro-sheets were prepared by molten salt method using the salt mixture of NaCl and NaF. FE-SEM, TEM, EDS, DTA-TG, XRD, Raman and FT-IR techniques were employed to characterize the morphology, phase composition and formation mechanism of the ZrO2 micro-sheets. The obtained monoclinic ZrO2 microsheets with exposed {100} facets show an average thickness of 0.2 ?m. The growth of the ZrO2 micro-sheets is proved to be assisted by the addition of fluoride. On the one hand, the addition of fluoride promotes the mass transfer of zirconia through the formation of zirconium fluoride complexes (ZrF 3-7). On the other hand, fluoride adsorbed on the surface of zirconia stabilizes {100} facets and lead to the exposure of {100} facets in the final product.
- Open Access
- 1 January 2018
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 12 (3) , 257-261
Facile molten salt synthesis of zirconia whiskers
ZrO2 whiskers have been synthesized by a facile molten salt method using ZrOCl2 ? 8H2O and Na3PO4 ? 12H2O as the zirconium source and molten salt, respectively. Differential thermal and thermogravimetric analyses, Xray diffraction analysis, field emission scanning electron microscope and transmission electron microscope were employed to characterize the heating process of the precursor mixture, phase composition of the assynthesized ZrO2 whiskers and the effect of reaction temperature on the synthesis of ZrO2 whiskers. The results show that the ZrO2 whiskers synthesized at 900?C have an average aspect ratio of 30 and preferentially grow along [010] direction. The formation of sodium zirconium phosphate [Na9-4xZrx(PO4)3] (x = 1, 2) and the reaction temperature play an important role in the growth of ZrO2 whiskers. This work also suggests an effective route for mass production of high quality ZrO2 whiskers.
- 1 January 2018
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 12 (3) , 257-261
Open AccessFacile molten salt synthesis of zirconia whiskers
ZrO2 whiskers have been synthesized by a facile molten salt method using ZrOCl2 ? 8H2O and Na3PO4 ? 12H2O as the zirconium source and molten salt, respectively. Differential thermal and thermogravimetric analyses, Xray diffraction analysis, field emission scanning electron microscope and transmission electron microscope were employed to characterize the heating process of the precursor mixture, phase composition of the assynthesized ZrO2 whiskers and the effect of reaction temperature on the synthesis of ZrO2 whiskers. The results show that the ZrO2 whiskers synthesized at 900?C have an average aspect ratio of 30 and preferentially grow along [010] direction. The formation of sodium zirconium phosphate [Na9-4xZrx(PO4)3] (x = 1, 2) and the reaction temperature play an important role in the growth of ZrO2 whiskers. This work also suggests an effective route for mass production of high quality ZrO2 whiskers.
- Open Access
- 1 January 2018
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 12 (2) , 95-99
Preliminary study on the growth mechanism of zircon whiskers prepared via non-hydrolytic sol-gel method combined with carbon black as reducing agent
Zircon whiskers were prepared at 700?C via non-hydrolytic sol-gel method combined with carbon black as reducing agent, Si(OC2H5)4 (TEOS) and ZrCl4 as precursors and LiF as mineralizer. The whiskers were characterized and their growth mechanism was discussed. The results show that the introduction of carbon black is beneficial for the preferential axial growth of zircon crystals into whiskers. The diameter and aspect ratio of zircon whiskers are 30-40 nm and 6-15, respectively. The zircon whiskers grow along the [001] direction, which is c-axis oriented. The growth mechanism is revealed to be the screw dislocation mechanism with the mass transport mainly from the zircon crystal particle matrix.
- 1 January 2018
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 12 (2) , 95-99
Open AccessPreliminary study on the growth mechanism of zircon whiskers prepared via non-hydrolytic sol-gel method combined with carbon black as reducing agent
Zircon whiskers were prepared at 700?C via non-hydrolytic sol-gel method combined with carbon black as reducing agent, Si(OC2H5)4 (TEOS) and ZrCl4 as precursors and LiF as mineralizer. The whiskers were characterized and their growth mechanism was discussed. The results show that the introduction of carbon black is beneficial for the preferential axial growth of zircon crystals into whiskers. The diameter and aspect ratio of zircon whiskers are 30-40 nm and 6-15, respectively. The zircon whiskers grow along the [001] direction, which is c-axis oriented. The growth mechanism is revealed to be the screw dislocation mechanism with the mass transport mainly from the zircon crystal particle matrix.
- Open Access
- 1 January 2018
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 12 (1) , 8-12
Synthesis and luminescent properties of novel red-emitting M7Sn(PO4)6:Eu3+(M= Sr,Ba) phosphors
Novel Eu3+-activated M7Sn(PO4)6 (where M = Sr, Ba) red-emitting phosphors were synthesized via conventional solid-state reaction method at 1200 ?C for 2 h. The luminescence properties of the prepared samples and quenching concentration of Sr7-xSn(PO4)6 :xEu3+ and Ba7-xSn(PO4)6 :xEu3+ were investigated. These phosphors can be efficiently excited by UV (395 nm) and visible blue (465 nm) light nicely matching the output wavelengths of the near-UV LEDs and InGaN blue LED chips and emit the red light. The critical concentrations of the Eu3+ activator were found to be 0.175mol and 0.21mol per formula unit for Sr7-xSn(PO4)6 :xEu3+ and Ba7-xSn(PO4)6 :xEu3+, respectively. The M7-xSn(PO4)6 :xEu3+ (M = Sr, Ba) phosphor may be a good candidate for light-emitting diodes application.
- 1 January 2018
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 12 (1) , 8-12
Open AccessSynthesis and luminescent properties of novel red-emitting M7Sn(PO4)6:Eu3+(M= Sr,Ba) phosphors
Novel Eu3+-activated M7Sn(PO4)6 (where M = Sr, Ba) red-emitting phosphors were synthesized via conventional solid-state reaction method at 1200 ?C for 2 h. The luminescence properties of the prepared samples and quenching concentration of Sr7-xSn(PO4)6 :xEu3+ and Ba7-xSn(PO4)6 :xEu3+ were investigated. These phosphors can be efficiently excited by UV (395 nm) and visible blue (465 nm) light nicely matching the output wavelengths of the near-UV LEDs and InGaN blue LED chips and emit the red light. The critical concentrations of the Eu3+ activator were found to be 0.175mol and 0.21mol per formula unit for Sr7-xSn(PO4)6 :xEu3+ and Ba7-xSn(PO4)6 :xEu3+, respectively. The M7-xSn(PO4)6 :xEu3+ (M = Sr, Ba) phosphor may be a good candidate for light-emitting diodes application.