Liang Yin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Liang Yin has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Jie Ding
College of Mechanical Engineering, Hunan University of Arts and Science, Changde, China
4 shared publicationsJiaqiang E
College of Mechanical and Vehicle Engineering, Hunan University, Changsha, Hunan 410073, China
2 shared publicationsYoujia Gao
Hunan Gaochuang Xiangyu Technology Co., Ltd., Changde, China
2 shared publications- Jun Guo
Faculty of Engineering Free University of Bozen-Bolzano 39100 Bolzano Italy
1 shared publication Jun Hu
Hunan Gaochuang Xiangyu Technology Co., Ltd., Changde, China
1 shared publicationLei Zhong
Hunan Gaochuang Xiangyu Technology Co., Ltd., Changde, China
1 shared publication
Latest Publications
- Open Access
- 1 January 2026
- Published by Tech Science Press in Fluid Dynamics & Materials Processing
- Vol. 22 (9) , 1-10
Active Cooling Technologies for Hypersonic Vehicles: Challenges, Advances, and Future Prospects
Hypersonic vehicles are subjected to extreme aerodynamic heating, making active cooling technologies a critical component of their thermal protection systems. This paper presents a comprehensive review of the fundamental principles, operating mechanisms, recent research developments, and key technical challenges associated with three major active cooling approaches: regenerative cooling, gas film cooling, and transpiration cooling. The review establishes a comparative framework to support the selection of cooling strategies according to specific mission requirements, while identifying current limitations and outlining priorities for future research. The analysis shows that regenerative cooling is well suited to long-duration missions owing to its high heat removal capability, although it requires complex structural integration. Gas film cooling offers a relatively simple and effective solution but demands a substantial coolant supply, which can reduce overall system efficiency. Transpiration cooling exhibits significant potential for next-generation hypersonic vehicles because of its exceptional thermal protection performance, yet its implementation remains constrained by demanding material and manufacturing requirements. Future advances are expected to arise from hybrid cooling architectures that combine the strengths of multiple techniques, together with intelligent thermal management systems capable of adapting to highly variable operating conditions.
- 1 January 2026
- Published by Tech Science Press in Fluid Dynamics & Materials Processing
- Vol. 22 (9) , 1-10
Open AccessActive Cooling Technologies for Hypersonic Vehicles: Challenges, Advances, and Future Prospects
Hypersonic vehicles are subjected to extreme aerodynamic heating, making active cooling technologies a critical component of their thermal protection systems. This paper presents a comprehensive review of the fundamental principles, operating mechanisms, recent research developments, and key technical challenges associated with three major active cooling approaches: regenerative cooling, gas film cooling, and transpiration cooling. The review establishes a comparative framework to support the selection of cooling strategies according to specific mission requirements, while identifying current limitations and outlining priorities for future research. The analysis shows that regenerative cooling is well suited to long-duration missions owing to its high heat removal capability, although it requires complex structural integration. Gas film cooling offers a relatively simple and effective solution but demands a substantial coolant supply, which can reduce overall system efficiency. Transpiration cooling exhibits significant potential for next-generation hypersonic vehicles because of its exceptional thermal protection performance, yet its implementation remains constrained by demanding material and manufacturing requirements. Future advances are expected to arise from hybrid cooling architectures that combine the strengths of multiple techniques, together with intelligent thermal management systems capable of adapting to highly variable operating conditions.
- Open Access
- 1 January 2026
- Published by Tech Science Press in Fluid Dynamics & Materials Processing
- Vol. 22 (4) , 1-10
Numerical Investigation of Flow and Heat Transfer in a Spider-Web-Inspired Microchannel Heat Sink
To address the thermal management challenges associated with localized high heat flux in electronic chips, this study proposes a bionic spider-web microchannel heat sink using deionized water as the coolant. Numerical simulations are conducted for two configurations, one with pinfins at the hotspot (Model A) and one without pinfins (Model B). The effects of Reynolds number and hotspot heat flux on flow distribution, pumping power, thermal resistance and temperature uniformity are systematically analyzed. Results show that the flow distribution varies significantly among channels, with higher flow rates near the inlet. Increasing the Reynolds number raises pumping power but reduces thermal resistance and improves hotspot temperature uniformity. Varying the heat flux variation has little effect on pumping power and thermal resistance; nevertheless, higher heat flux values lead to an increases in the temperature difference across the hotspot, worsening uniformity. The pinfin structure enhances local heat transfer, strengthens hotspot cooling and improves overall temperature uniformity. It is shown that a spider-web heat sink can effectively manage a heat flux as high as 480 W/cm2, thereby demonstrating its potential for next-generation high-power electronics cooling.
- 1 January 2026
- Published by Tech Science Press in Fluid Dynamics & Materials Processing
- Vol. 22 (4) , 1-10
Open AccessNumerical Investigation of Flow and Heat Transfer in a Spider-Web-Inspired Microchannel Heat Sink
To address the thermal management challenges associated with localized high heat flux in electronic chips, this study proposes a bionic spider-web microchannel heat sink using deionized water as the coolant. Numerical simulations are conducted for two configurations, one with pinfins at the hotspot (Model A) and one without pinfins (Model B). The effects of Reynolds number and hotspot heat flux on flow distribution, pumping power, thermal resistance and temperature uniformity are systematically analyzed. Results show that the flow distribution varies significantly among channels, with higher flow rates near the inlet. Increasing the Reynolds number raises pumping power but reduces thermal resistance and improves hotspot temperature uniformity. Varying the heat flux variation has little effect on pumping power and thermal resistance; nevertheless, higher heat flux values lead to an increases in the temperature difference across the hotspot, worsening uniformity. The pinfin structure enhances local heat transfer, strengthens hotspot cooling and improves overall temperature uniformity. It is shown that a spider-web heat sink can effectively manage a heat flux as high as 480 W/cm2, thereby demonstrating its potential for next-generation high-power electronics cooling.
- 2 May 2024
- Published by Springer Nature in Journal of Applied Mathematics and Computing
- Vol. 70 (4) , 3219-3233
A dimension expanded Newton-type method for absolute value equations
- 2 May 2024
- Published by Springer Nature in Journal of Applied Mathematics and Computing
- Vol. 70 (4) , 3219-3233
A dimension expanded Newton-type method for absolute value equations
- Open Access
- 20 September 2022
- Published by Hindawi Limited in International Journal of Aerospace Engineering
- Vol. 2022, 1-12
Numerical Study of Air Distribution System for a Passenger Aircraft Based on 1D and 3D Coupling
Numerical Study of Air Distribution System for a Passenger Aircraft Based on 1D and 3D Coupling: The air distribution system is one of the key systems for ensuring the safety and comfort of the passenger aircraft. The large number of components poses a severe challenge to the efficiency, accuracy, and convergence of system simulation. For the 3D CFD method, the complex and large number of meshes leads to low computational efficiency. The 1D simulation has high efficiency, but the local accuracy is inadequate. To solve this problem, the 1D Fluid System Simulation Software Flomaster with the linearization algorithm is used to establish the system-level model. The flow characteristic curve is obtained by the CFD (computational fluid dynamics) method for the local irregular ducts and introduced into the 1D system model for iteration. The effects of local flow resistance and thermal insulation on the flow distribution and thermal performance of the system are studied using this simulation model. The results show that the local flow resistance affects the total flow and uniformity of the cabin distribution, the improvement of insulation performance is weakened with increasing insulation layer thickness, and the application of thicker insulation layers on the downstream pipeline is more advantageous to limit the maximum temperature change of the conditioned air.
- 20 September 2022
- Published by Hindawi Limited in International Journal of Aerospace Engineering
- Vol. 2022, 1-12
Open AccessNumerical Study of Air Distribution System for a Passenger Aircraft Based on 1D and 3D Coupling
Numerical Study of Air Distribution System for a Passenger Aircraft Based on 1D and 3D Coupling: The air distribution system is one of the key systems for ensuring the safety and comfort of the passenger aircraft. The large number of components poses a severe challenge to the efficiency, accuracy, and convergence of system simulation. For the 3D CFD method, the complex and large number of meshes leads to low computational efficiency. The 1D simulation has high efficiency, but the local accuracy is inadequate. To solve this problem, the 1D Fluid System Simulation Software Flomaster with the linearization algorithm is used to establish the system-level model. The flow characteristic curve is obtained by the CFD (computational fluid dynamics) method for the local irregular ducts and introduced into the 1D system model for iteration. The effects of local flow resistance and thermal insulation on the flow distribution and thermal performance of the system are studied using this simulation model. The results show that the local flow resistance affects the total flow and uniformity of the cabin distribution, the improvement of insulation performance is weakened with increasing insulation layer thickness, and the application of thicker insulation layers on the downstream pipeline is more advantageous to limit the maximum temperature change of the conditioned air.
- Open Access
- 8 September 2022
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2022, 1-10
Effect of Cooling Header on the Hydrocarbon Fuel Flow Distribution in a Regenerative Cooling Channel
Regenerative cooling technology is the most widely used cooling technology in liquid rocket engines, and flow distribution is very important for regenerative cooling heat transfer. In this work, the flow distribution characteristics of -type parallel channels were studied through numerical simulation, and the effects of flow area ratio, inlet header shape, and inlet aspect ratio were analyzed. Results showed that changing the inlet cooling header can improve the uniform distribution of flow rate effectively. The nonuniformity coefficient and fuel temperature varied with change in the flow area ratio, inlet header shape, and inlet aspect ratio. The maximum temperature of the wall decreased from 1334.52 K to 1220.61 K when the flow area ratio was changed from 1 to 0.25. An appropriate decrement in the inlet header shape was beneficial to the uniform flow distribution. The inlet aspect ratio should be reduced properly to ensure that each channel experiences similar pressure drop. This research has a certain reference value for the structural design of regenerative cooling channels.
- 8 September 2022
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2022, 1-10
Open AccessEffect of Cooling Header on the Hydrocarbon Fuel Flow Distribution in a Regenerative Cooling Channel
Regenerative cooling technology is the most widely used cooling technology in liquid rocket engines, and flow distribution is very important for regenerative cooling heat transfer. In this work, the flow distribution characteristics of -type parallel channels were studied through numerical simulation, and the effects of flow area ratio, inlet header shape, and inlet aspect ratio were analyzed. Results showed that changing the inlet cooling header can improve the uniform distribution of flow rate effectively. The nonuniformity coefficient and fuel temperature varied with change in the flow area ratio, inlet header shape, and inlet aspect ratio. The maximum temperature of the wall decreased from 1334.52 K to 1220.61 K when the flow area ratio was changed from 1 to 0.25. An appropriate decrement in the inlet header shape was beneficial to the uniform flow distribution. The inlet aspect ratio should be reduced properly to ensure that each channel experiences similar pressure drop. This research has a certain reference value for the structural design of regenerative cooling channels.
- 1 April 2021
- Published by Elsevier in Acta Astronautica
- Vol. 181, 377-383
An experimental study on the spray characteristics of splash platelet injector
- 1 April 2021
- Published by Elsevier in Acta Astronautica
- Vol. 181, 377-383
An experimental study on the spray characteristics of splash platelet injector
- Open Access
- 30 December 2017
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 104 (1) , 012002
Effect of Structural Parameters on the Combustion Performance of Platelet Engines
- 30 December 2017
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 104 (1) , 012002
Open AccessEffect of Structural Parameters on the Combustion Performance of Platelet Engines
- Open Access
- 9 May 2017
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 63 (1) , 012021
Numerical Simulation on the Combustion Characteristic of GO2/GCH4 Splash Platelet Injector
The platelet injector flow is quite different from other injectors due to the platelet technology and complex injection method. This work is aimed at assessing the effect of characteristic chamber length and middle-plate thickness for single-element splash platelet injector. Numerical simulation was adopted to investigate the gaseous methane and gaseous oxygen flow and combustion characteristics. Both characteristic velocity and combustion efficiency are examined for injector design. The results indicate that, with a 0.6mm middleplate thickness the injector can reach the maximum combustion efficiency and shortest combustion length, but the differences are not obvious for all cases. The characteristic chamber length can be shortened effectively by using splash platelet injector.
- 9 May 2017
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 63 (1) , 012021
Open AccessNumerical Simulation on the Combustion Characteristic of GO2/GCH4 Splash Platelet Injector
The platelet injector flow is quite different from other injectors due to the platelet technology and complex injection method. This work is aimed at assessing the effect of characteristic chamber length and middle-plate thickness for single-element splash platelet injector. Numerical simulation was adopted to investigate the gaseous methane and gaseous oxygen flow and combustion characteristics. Both characteristic velocity and combustion efficiency are examined for injector design. The results indicate that, with a 0.6mm middleplate thickness the injector can reach the maximum combustion efficiency and shortest combustion length, but the differences are not obvious for all cases. The characteristic chamber length can be shortened effectively by using splash platelet injector.