Vlasis K. Koumousis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vlasis K. Koumousis has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Savvas P. Triantafyllou
Laboratory of Structural Analysis and Aseismic, School of Civil Engineering, National Technical University of Athens, Athens, Greece
4 shared publications - I.A. Gkimousis
Ph.D. Candidate, Institute of Structural Analysis and Aseismic Research, National Technical Univ. of Athens, Zografou Campus, Athens 15780, Greece
2 shared publications - C. K. Dimou
Postdoctoral Researcher, National Technical Univ. of Athens, Institute of Structural Analysis and Seismic Research, Zografou Campus, Iroon Polytexneiou 9, 15780 Athens, Greece
1 shared publication Ch. Andriotis
Ph.D. Candidate, Institute of Structural Analysis and Aseismic Research, National Technical Univ. of Athens, Zografou Campus, Athens 15780, Greece
1 shared publication- Christos D. Sofianos
National Technical University of Athens
1 shared publication Ilias A. Gkimousis
National Technical University of Athens
1 shared publication
Latest Publications
- 20 May 2018
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 47 (9) , 1942-1962
Modeling RC column flexural failure modes under intensive seismic loading
Summary: The aim of this work is to model beam‐column behavior in a computationally effective manner, revealing reliably the overall response of reinforced concrete members subjected to intensive seismic loading. In this respect, plasticity and damage are considered in the predominant longitudinal direction, allowing for fiber finite element modeling, while in addition the effect of inelastic buckling of longitudinal rebars, which becomes essential at later stages of intensive cyclic loading, is incorporated. Α smooth plasticity‐damage model is developed for concrete, accounting for unilateral compressive and tensile behavior, nonlinear unloading and crack closure phenomena. This is used to address concrete core crushing and spalling, which triggers the inelastic buckling of longitudinal rebars. For this reason, a uniaxial local stress‐strain constitutive relation for steel rebars is developed, which is based on a combined nonlinear kinematic and isotropic hardening law. The proposed constitutive model is validated on the basis of existing experimental data and the formulation of the buckling model for a single rebar is developed. The cross section of rebar is discretized into fibers, each one following the derived stress‐strain uniaxial law. The buckling curve is determined analytically, while equilibrium is imposed at the deformed configuration. The proposed models for concrete and rebars are embedded into a properly adjusted fiber beam‐column element of reinforced concrete members and the proposed formulation is verified with existing experimental data under intensive cyclic loading.
- 20 May 2018
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 47 (9) , 1942-1962
Modeling RC column flexural failure modes under intensive seismic loading
Summary: The aim of this work is to model beam‐column behavior in a computationally effective manner, revealing reliably the overall response of reinforced concrete members subjected to intensive seismic loading. In this respect, plasticity and damage are considered in the predominant longitudinal direction, allowing for fiber finite element modeling, while in addition the effect of inelastic buckling of longitudinal rebars, which becomes essential at later stages of intensive cyclic loading, is incorporated. Α smooth plasticity‐damage model is developed for concrete, accounting for unilateral compressive and tensile behavior, nonlinear unloading and crack closure phenomena. This is used to address concrete core crushing and spalling, which triggers the inelastic buckling of longitudinal rebars. For this reason, a uniaxial local stress‐strain constitutive relation for steel rebars is developed, which is based on a combined nonlinear kinematic and isotropic hardening law. The proposed constitutive model is validated on the basis of existing experimental data and the formulation of the buckling model for a single rebar is developed. The cross section of rebar is discretized into fibers, each one following the derived stress‐strain uniaxial law. The buckling curve is determined analytically, while equilibrium is imposed at the deformed configuration. The proposed models for concrete and rebars are embedded into a properly adjusted fiber beam‐column element of reinforced concrete members and the proposed formulation is verified with existing experimental data under intensive cyclic loading.
- 1 June 2017
- Published by Springer Nature in Archive of Applied Mechanics
- Vol. 88 (1-2) , 253-269
Hysteretic beam element with degrading smooth models
- 1 June 2017
- Published by Springer Nature in Archive of Applied Mechanics
- Vol. 88 (1-2) , 253-269
Hysteretic beam element with degrading smooth models
- 1 February 2016
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 142 (2)
Modeling Reinforced Concrete Structures Using Smooth Plasticity and Damage Models
In this work, a new smooth model for uniaxial concrete behavior that combines plasticity and damage considerations, together with unsymmetrical hysteresis for tension compression and nonlinear unloading, is presented. Softening and stiffness degradation phenomena are handled through a scalar damage-driving variable, which is a function of total strain. Smoothening of the incremental damage behavior is achieved, following similar steps as for Bouc-Wen modeling of classical plasticity, thus exploiting their common mathematical structure. The uniaxial model for concrete, together with the standard steel model exhibiting kinematic hardening, are employed to derive a fiber beam-column element that is used to assemble the numerical model of frame structures. Following the displacement-based approach, the solution of the entire system is established using a standard Newton-Raphson numerical scheme, which incorporates the evolution equations of all fibers elevated at the section, element, and structural l...
- 1 February 2016
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 142 (2)
Modeling Reinforced Concrete Structures Using Smooth Plasticity and Damage Models
In this work, a new smooth model for uniaxial concrete behavior that combines plasticity and damage considerations, together with unsymmetrical hysteresis for tension compression and nonlinear unloading, is presented. Softening and stiffness degradation phenomena are handled through a scalar damage-driving variable, which is a function of total strain. Smoothening of the incremental damage behavior is achieved, following similar steps as for Bouc-Wen modeling of classical plasticity, thus exploiting their common mathematical structure. The uniaxial model for concrete, together with the standard steel model exhibiting kinematic hardening, are employed to derive a fiber beam-column element that is used to assemble the numerical model of frame structures. Following the displacement-based approach, the solution of the entire system is established using a standard Newton-Raphson numerical scheme, which incorporates the evolution equations of all fibers elevated at the section, element, and structural l...
- 1 January 2016
- Published by Elsevier in Engineering Structures
- Vol. 106, 399-409
Inelastic mixed fiber beam finite element for steel cyclic behavior
- 1 January 2016
- Published by Elsevier in Engineering Structures
- Vol. 106, 399-409
Inelastic mixed fiber beam finite element for steel cyclic behavior
- 1 January 2013
- Published by Springer Nature
- p. 297-316
Collapse Fragility Curves of RC Frames with Varying Design Parameters
- 1 January 2013
- Published by Springer Nature
- p. 297-316
Collapse Fragility Curves of RC Frames with Varying Design Parameters
- 6 July 2012
- Published by Springer Nature in Archive of Applied Mechanics
- Vol. 82 (10-11) , 1675-1687
An hysteretic quadrilateral plane stress element
- 6 July 2012
- Published by Springer Nature in Archive of Applied Mechanics
- Vol. 82 (10-11) , 1675-1687
An hysteretic quadrilateral plane stress element
- 1 March 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 138 (3) , 235-246
Bouc-Wen Type Hysteretic Plane Stress Element
In this work, a plane-stress element is proposed for the elastoplastic dynamic analysis of two-dimensional structures exhibiting hysteretic behavior. The constant-strain triangular element formulation for the elastic case is modified by introducing the Bouc-Wen hysteretic model, properly defined in the 2D stress-strain space. Solutions are obtained by simultaneously solving two sets of governing equations, namely the global equilibrium equations and the local constitutive equations, using a predictor-corrector differential equation solver. In following the proposed method, the linearization of the constitutive relations usually performed in step-by-step solution approaches is avoided. The proposed element is capable of modeling cyclic induced phenomena such as stiffness degradation and strength deterioration. Furthermore, the solution method implemented improves the accuracy of the results without increasing the computational cost of the analysis. Examples are presented which demonstrate the efficiency of the proposed approach. The method can be extended to other types of finite elements by properly incorporating the nonlinear constitutive behavior into their stiffness matrices.
- 1 March 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 138 (3) , 235-246
Bouc-Wen Type Hysteretic Plane Stress Element
In this work, a plane-stress element is proposed for the elastoplastic dynamic analysis of two-dimensional structures exhibiting hysteretic behavior. The constant-strain triangular element formulation for the elastic case is modified by introducing the Bouc-Wen hysteretic model, properly defined in the 2D stress-strain space. Solutions are obtained by simultaneously solving two sets of governing equations, namely the global equilibrium equations and the local constitutive equations, using a predictor-corrector differential equation solver. In following the proposed method, the linearization of the constitutive relations usually performed in step-by-step solution approaches is avoided. The proposed element is capable of modeling cyclic induced phenomena such as stiffness degradation and strength deterioration. Furthermore, the solution method implemented improves the accuracy of the results without increasing the computational cost of the analysis. Examples are presented which demonstrate the efficiency of the proposed approach. The method can be extended to other types of finite elements by properly incorporating the nonlinear constitutive behavior into their stiffness matrices.
- 1 January 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 138 (1) , 36-49
Small and Large Displacement Dynamic Analysis of Frame Structures Based on Hysteretic Beam Elements
In this work, a beam element is proposed for the nonlinear dynamic analysis of frame structures. The classical Euler-Bernoulli formulation for the elastic beam is extended by implicitly defining new hysteretic degrees of freedom, subjected to evolution equations of the Bouc-Wen type with kinematic hardening. A linear interpolation field is employed for these new degrees of freedom, which are regarded as hysteretic curvatures and hysteretic axial deformations. By means of the principle of virtual work, an elastoplastic hysteretic stiffness relation is derived, which together with the hysteretic evolution equations fully describes the behavior of the element. The elemental stiffness equations are assembled to form a system of linear global equations of motion that also depend on the introduced hysteretic variables. The solution is obtained by simultaneously solving the entire set of governing equations, namely the linear global equations of motion with constant coefficient matrices, and the nonlinear local ...
- 1 January 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 138 (1) , 36-49
Small and Large Displacement Dynamic Analysis of Frame Structures Based on Hysteretic Beam Elements
In this work, a beam element is proposed for the nonlinear dynamic analysis of frame structures. The classical Euler-Bernoulli formulation for the elastic beam is extended by implicitly defining new hysteretic degrees of freedom, subjected to evolution equations of the Bouc-Wen type with kinematic hardening. A linear interpolation field is employed for these new degrees of freedom, which are regarded as hysteretic curvatures and hysteretic axial deformations. By means of the principle of virtual work, an elastoplastic hysteretic stiffness relation is derived, which together with the hysteretic evolution equations fully describes the behavior of the element. The elemental stiffness equations are assembled to form a system of linear global equations of motion that also depend on the introduced hysteretic variables. The solution is obtained by simultaneously solving the entire set of governing equations, namely the linear global equations of motion with constant coefficient matrices, and the nonlinear local ...
- 28 June 2011
- Published by Springer Nature in Computational Mechanics
- Vol. 48 (6) , 713-727
An inelastic Timoshenko beam element with axial–shear–flexural interaction
- 28 June 2011
- Published by Springer Nature in Computational Mechanics
- Vol. 48 (6) , 713-727
An inelastic Timoshenko beam element with axial–shear–flexural interaction
- 1 March 2009
- Published by American Society of Civil Engineers (ASCE) in Journal of Computing in Civil Engineering
- Vol. 23 (2) , 100-109
Reliability-Based Optimal Design of Truss Structures Using Particle Swarm Optimization
In this work, the particle swarm optimization method is employed for the reliability-based optimal design of statically determinate truss structures. Particle swarm optimization is inspired by the social behavior of flocks (swarms) of birds and insects (particles). Every particle’s position represents a specific design. The algorithm searches the design space by adjusting the trajectories of the particles that comprise the swarm. These particles are attracted toward the positions of both their personal best solution and the best solution of the swarm in a stochastic manner. In typical structural optimization problems, safety is dealt with in a yes/no manner fulfilling the set of requirements imposed by codes of practice. Considering uncertainty for the problem parameters offers a measure to quantify safety. This measure provides a rational basis for the estimation of the reliability of the components and of the entire system. Incorporating the reliability into the structural optimization framework one can...
- 1 March 2009
- Published by American Society of Civil Engineers (ASCE) in Journal of Computing in Civil Engineering
- Vol. 23 (2) , 100-109
Reliability-Based Optimal Design of Truss Structures Using Particle Swarm Optimization
In this work, the particle swarm optimization method is employed for the reliability-based optimal design of statically determinate truss structures. Particle swarm optimization is inspired by the social behavior of flocks (swarms) of birds and insects (particles). Every particle’s position represents a specific design. The algorithm searches the design space by adjusting the trajectories of the particles that comprise the swarm. These particles are attracted toward the positions of both their personal best solution and the best solution of the swarm in a stochastic manner. In typical structural optimization problems, safety is dealt with in a yes/no manner fulfilling the set of requirements imposed by codes of practice. Considering uncertainty for the problem parameters offers a measure to quantify safety. This measure provides a rational basis for the estimation of the reliability of the components and of the entire system. Incorporating the reliability into the structural optimization framework one can...