Ali Al-Yacoub
Research Subjects
Ali Al-Yacoub has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Ella-Mae Hubbard
Loughborough University, Wolfson School, Intelligent Automation Centre, Loughborough, UK
2 shared publications- Khaled Elgeneidy
British University in Egypt (BUE)
2 shared publications Niels Lohse
Loughborough University, Wolfson School, Intelligent Automation Centre, Loughborough, UK
2 shared publicationsPedro Ferreira
Loughborough University, Wolfson School, Intelligent Automation Centre, Loughborough, UK
2 shared publications- Ronglei Sun
Institute of Medical Equipment Science and Engineering, State Key Laboratory of Intelligent Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China
2 shared publications - Wael Taie
School of Mechanical Science and Engineering, Huazhong University of Science and Technology,Wuhan,China
2 shared publications
Latest Publications
- 19 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 241-245
Payload Parameters Identification Using Incremental Ensemble Learning
This paper introduces a new method for identifying the payload inertial parameters for collaborative robots (cobots) that operate in dynamic manufacturing environments with frequent reconfiguration. The proposed method eliminates the need for specific excitation trajectories during the identification process, allowing the identification of payload parameters while the cobot follows any arbitrary task trajectory. This is achieved via an incremental ensemble model, which utilizes incremental neural networks as weak learners. The proposed method successfully adapts the ensemble model to new task paths while maintaining accurate estimations for the payload parameters. The mean absolute error for mass, center of mass, and the moment of inertia parameters were 0.01 kg, 0.0068 kg.m, and 0.0008 kg.m 2 , respectively. These results demonstrate the effectiveness of the model in dealing with new task trajectories in comparison to traditional or batch ensemble models.
- 19 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 241-245
Payload Parameters Identification Using Incremental Ensemble Learning
This paper introduces a new method for identifying the payload inertial parameters for collaborative robots (cobots) that operate in dynamic manufacturing environments with frequent reconfiguration. The proposed method eliminates the need for specific excitation trajectories during the identification process, allowing the identification of payload parameters while the cobot follows any arbitrary task trajectory. This is achieved via an incremental ensemble model, which utilizes incremental neural networks as weak learners. The proposed method successfully adapts the ensemble model to new task paths while maintaining accurate estimations for the payload parameters. The mean absolute error for mass, center of mass, and the moment of inertia parameters were 0.01 kg, 0.0068 kg.m, and 0.0008 kg.m 2 , respectively. These results demonstrate the effectiveness of the model in dealing with new task trajectories in comparison to traditional or batch ensemble models.
- 22 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (2) , 1350-1356
Online Identification of Payload Inertial Parameters Using Ensemble Learning for Collaborative Robots
Collaborative robots (Cobots) are essential in flexible automation solutions, enabling fast and easy reconfiguration to adapt to varying task requirements in dynamic environments. This requires the ability to safely handle different payloads with varying inertial parameters, which may not be known in advance. Hence, online identification of the payload's inertial parameters becomes essential for safe interactions, accurate path following, and stable grasping. Most existing methods require additional sensors, calibration procedures, or custom filtering, which increases the complexity and estimation time. In this letter, we propose a novel online identification method that employs a bagging ensemble machine learning approach to identify the payload inertial parameters without external sensors or additional filtering and calibration steps. The method uses available joint position, velocity, and torque measurements from the Cobot to train neural networks and decision trees as weak learners. The method is tested in simulation and validated using the Franka Emika Panda Cobot. The results showed that our method outperforms the state-of-the-art recursive least square methods reducing prediction errors by 75%–78% for mass and 49.5%–60% for the center of mass, while estimating accurate payload parameters within the first time step.
- 22 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (2) , 1350-1356
Online Identification of Payload Inertial Parameters Using Ensemble Learning for Collaborative Robots
Collaborative robots (Cobots) are essential in flexible automation solutions, enabling fast and easy reconfiguration to adapt to varying task requirements in dynamic environments. This requires the ability to safely handle different payloads with varying inertial parameters, which may not be known in advance. Hence, online identification of the payload's inertial parameters becomes essential for safe interactions, accurate path following, and stable grasping. Most existing methods require additional sensors, calibration procedures, or custom filtering, which increases the complexity and estimation time. In this letter, we propose a novel online identification method that employs a bagging ensemble machine learning approach to identify the payload inertial parameters without external sensors or additional filtering and calibration steps. The method uses available joint position, velocity, and torque measurements from the Cobot to train neural networks and decision trees as weak learners. The method is tested in simulation and validated using the Franka Emika Panda Cobot. The results showed that our method outperforms the state-of-the-art recursive least square methods reducing prediction errors by 75%–78% for mass and 49.5%–60% for the center of mass, while estimating accurate payload parameters within the first time step.
- Open Access
- 21 June 2022
- Published by Taylor & Francis in Production & Manufacturing Research
- Vol. 10 (1) , 410-427
Experimental study to investigate mental workload of local vs remote operator in human-machine interaction
A new Coronavirus disease 2019 has spread globally since 2019. Consequently, businesses from different sectors were forced to work remotely. At the same time, research in this area has seen a rise in studying and emerging technologies that allow and promote such a remote working style; not every sector is equipped for such a transition. The manufacturing sector especially, has faced challenges in this respect. This paper investigates the mental workload (MWL) of two groups of participants through a human-machine interaction task. Participants were required to bring a robotised cell to full production by tuning system and dispensing process parameters. Following the experiment, a self-assessment of the participants’ perceived MWL using the raw NASA Task Load Index (RTLX) was collected. The results reveal that remote participants tend to have a lower perceived workload compared to the local participants, but mental demand was deemed higher while performance was rated lower.
- 21 June 2022
- Published by Taylor & Francis in Production & Manufacturing Research
- Vol. 10 (1) , 410-427
Open AccessExperimental study to investigate mental workload of local vs remote operator in human-machine interaction
A new Coronavirus disease 2019 has spread globally since 2019. Consequently, businesses from different sectors were forced to work remotely. At the same time, research in this area has seen a rise in studying and emerging technologies that allow and promote such a remote working style; not every sector is equipped for such a transition. The manufacturing sector especially, has faced challenges in this respect. This paper investigates the mental workload (MWL) of two groups of participants through a human-machine interaction task. Participants were required to bring a robotised cell to full production by tuning system and dispensing process parameters. Following the experiment, a self-assessment of the participants’ perceived MWL using the raw NASA Task Load Index (RTLX) was collected. The results reveal that remote participants tend to have a lower perceived workload compared to the local participants, but mental demand was deemed higher while performance was rated lower.
- Open Access
- 22 June 2021
- Published by MDPI AG in Electronics
- Vol. 10 (13) , 1509
Data-Driven Modelling of Human-Human Co-Manipulation Using Force and Muscle Surface Electromyogram Activities
With collaborative robots and the recent developments in manufacturing technologies, physical interactions between humans and robots represent a vital role in performing collaborative tasks. Most previous studies have focused on robot motion planning and control during the execution of the task. However, further research is required for direct physical contact for human-robot or robot-robot interactions, such as co-manipulation. In co-manipulation, a human operator manipulates a shared load with a robot through a semi-structured environment. In such scenarios, a multi-contact point with the environment during the task execution results in a convoluted force/toque signature that is difficult to interpret. Therefore, in this paper, a muscle activity sensor in the form of an electromyograph (EMG) is employed to improve the mapping between force/torque and displacements in co-manipulation tasks. A suitable mapping was identified by comparing the root mean square error amongst data-driven models, mathematical models, and hybrid models. Thus, a robot was shown to effectively and naturally perform the required co-manipulation with a human. This paper’s proposed hypotheses were validated using an unseen test dataset and a simulated co-manipulation experiment, which showed that the EMG and data-driven model improved the mapping of the force/torque features into displacements.
- 22 June 2021
- Published by MDPI AG in Electronics
- Vol. 10 (13) , 1509
Open AccessData-Driven Modelling of Human-Human Co-Manipulation Using Force and Muscle Surface Electromyogram Activities
With collaborative robots and the recent developments in manufacturing technologies, physical interactions between humans and robots represent a vital role in performing collaborative tasks. Most previous studies have focused on robot motion planning and control during the execution of the task. However, further research is required for direct physical contact for human-robot or robot-robot interactions, such as co-manipulation. In co-manipulation, a human operator manipulates a shared load with a robot through a semi-structured environment. In such scenarios, a multi-contact point with the environment during the task execution results in a convoluted force/toque signature that is difficult to interpret. Therefore, in this paper, a muscle activity sensor in the form of an electromyograph (EMG) is employed to improve the mapping between force/torque and displacements in co-manipulation tasks. A suitable mapping was identified by comparing the root mean square error amongst data-driven models, mathematical models, and hybrid models. Thus, a robot was shown to effectively and naturally perform the required co-manipulation with a human. This paper’s proposed hypotheses were validated using an unseen test dataset and a simulated co-manipulation experiment, which showed that the EMG and data-driven model improved the mapping of the force/torque features into displacements.
- Open Access
- 1 June 2021
- Published by Elsevier in Robotics and Computer-Integrated Manufacturing
- Vol. 69
Improving human robot collaboration through Force/Torque based learning for object manipulation
- 1 June 2021
- Published by Elsevier in Robotics and Computer-Integrated Manufacturing
- Vol. 69
Open AccessImproving human robot collaboration through Force/Torque based learning for object manipulation
- Open Access
- 17 October 2019
- Published by Frontiers Media SA in Frontiers in Robotics and AI
- Vol. 6
Symbolic-Based Recognition of Contact States for Learning Assembly Skills
Imitation learning is gaining more attention because it enables robots to learn skills from human demonstrations. One of the major industrial activities that can benefit from imitation learning is the learning of new assembly processes. An essential characteristic of an assembly skill is its different contact states (CS). They determine how to adjust movements in order to perform the assembly task successfully. Humans can recognize CSs through haptic feedback. They execute complex assembly tasks accordingly. Hence, CSs are generally recognized using force and torque information. This process is not straightforward due to the variations in assembly tasks, signal noise and ambiguity in interpreting force/torque (F/T) information. In this research, an investigation has been conducted to recognize the CSs during an assembly process with a geometrical variation on the mating parts. The F/T data collected from several human trials were pre-processed, segmented and represented as symbols. Those symbols were used to train a probabilistic model. Then, the trained model was validated using unseen datasets. The primary goal of the proposed approach aims to improve recognition accuracy and reduce the computational effort by employing symbolic and probabilistic approaches. The model successfully recognized CS based only on force information. This shows that such models can assist in imitation learning.
- 17 October 2019
- Published by Frontiers Media SA in Frontiers in Robotics and AI
- Vol. 6
Open AccessSymbolic-Based Recognition of Contact States for Learning Assembly Skills
Imitation learning is gaining more attention because it enables robots to learn skills from human demonstrations. One of the major industrial activities that can benefit from imitation learning is the learning of new assembly processes. An essential characteristic of an assembly skill is its different contact states (CS). They determine how to adjust movements in order to perform the assembly task successfully. Humans can recognize CSs through haptic feedback. They execute complex assembly tasks accordingly. Hence, CSs are generally recognized using force and torque information. This process is not straightforward due to the variations in assembly tasks, signal noise and ambiguity in interpreting force/torque (F/T) information. In this research, an investigation has been conducted to recognize the CSs during an assembly process with a geometrical variation on the mating parts. The F/T data collected from several human trials were pre-processed, segmented and represented as symbols. Those symbols were used to train a probabilistic model. Then, the trained model was validated using unseen datasets. The primary goal of the proposed approach aims to improve recognition accuracy and reduce the computational effort by employing symbolic and probabilistic approaches. The model successfully recognized CS based only on force information. This shows that such models can assist in imitation learning.