Yuan Gao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yuan Gao has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Jürgen Leopold
Precision Engineering Department, Fraunhofer Institute for Machine Tools and Forming Technology, Chemnitz 09661, Germany
1 shared publication Liu Yang
1 shared publicationMengfei Han
1 shared publication- Ronglei Sun
Institute of Medical Equipment Science and Engineering, State Key Laboratory of Intelligent Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China
1 shared publication Xiaojun Lin
School of Mechanical Engineering, Northwestern Polytechnical University, Xian, China
1 shared publicationXin Liu
1 shared publication
Latest Publications
- Open Access
Spatiotemporal dynamics of frontoparietal networks in semantic intuitive decision-making
- 9 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 27 (3) , 1796-1807
Path Generation for Flexible Flank Polishing on Freeform Surfaces With Uniform Over-Cuts
One of the bottlenecks in flexible flank polishing is the nonuniform overcuts problem caused by the difficulties of the polishing tool to conform to variable curvatures of the freeform surface along the polishing path. Consequently, it will significantly reduce the quality of finished surfaces and the service life of polishing tools. To solve the problem, a novel path generation method is proposed in this article, which not only gets the uniform overcut at a single cutter location, but also keeps its uniformity over an entire polishing path. First, a tool orientation model is built on the freeform surface by analyzing the process of flexible flank polishing. Then, a novel indicator of overcut uniformity is proposed with the developed Dupin indicatrix, and the tool orientation is determined by maximizing the indicator. Next, based on Taylor expansion, a polishing path generation method is presented with the consideration of overcut uniformity. Finally, the proposed method is verified and analyzed relative to a comparison method by both virtual simulations and physical experiments. These results present a good consistency with each other and together provide strong support for the correctness, feasibility, and efficiency of the proposed method, which further contributes to surface quality and polishing tool's service life.
- 9 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 27 (3) , 1796-1807
Path Generation for Flexible Flank Polishing on Freeform Surfaces With Uniform Over-Cuts
One of the bottlenecks in flexible flank polishing is the nonuniform overcuts problem caused by the difficulties of the polishing tool to conform to variable curvatures of the freeform surface along the polishing path. Consequently, it will significantly reduce the quality of finished surfaces and the service life of polishing tools. To solve the problem, a novel path generation method is proposed in this article, which not only gets the uniform overcut at a single cutter location, but also keeps its uniformity over an entire polishing path. First, a tool orientation model is built on the freeform surface by analyzing the process of flexible flank polishing. Then, a novel indicator of overcut uniformity is proposed with the developed Dupin indicatrix, and the tool orientation is determined by maximizing the indicator. Next, based on Taylor expansion, a polishing path generation method is presented with the consideration of overcut uniformity. Finally, the proposed method is verified and analyzed relative to a comparison method by both virtual simulations and physical experiments. These results present a good consistency with each other and together provide strong support for the correctness, feasibility, and efficiency of the proposed method, which further contributes to surface quality and polishing tool's service life.
- 1 June 2016
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 111-112, 88-100
Analysis of chip morphology and surface topography in modulation assisted machining
- 1 June 2016
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 111-112, 88-100
Analysis of chip morphology and surface topography in modulation assisted machining