Hans Bodén
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hans Bodén has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Mats Åbom
The Marcus Wallenberg Lab., KTH-The Royal Inst of Technol., Teknikringen 8, Stockholm 10044, Sweden
2 shared publications - André Mateus Netto Spillere
Federal University of Santa Catarina
1 shared publication - Antti Hynninen
VTT Technical Research Centre of Finland Ltd., P.O. Box 1000, FI-02044, VTT, Finland
1 shared publication - Hans Rämmal
Tallinn University of Technology
1 shared publication - Julio Apolinario Cordioli
Federal University of Santa Catarina
1 shared publication - Luck Peerlings
KTH Royal Inst Technol, Dept Aeronaut & Vehicle Engn, Marcus Wallenberg Lab Sound & Vibrat, Teknikringen 8, SE-10044 Stockholm, Sweden
1 shared publication
Latest Publications
- 1 September 2019
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 457, 197-211
Experimental investigation of the aero-acoustic interaction at an area-expansion
- 1 September 2019
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 457, 197-211
Experimental investigation of the aero-acoustic interaction at an area-expansion
- 1 March 2019
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 57 (3) , 1044-1054
Optimum Impedance in the Presence of an Inviscid Sheared Flow
- 1 March 2019
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 57 (3) , 1044-1054
Optimum Impedance in the Presence of an Inviscid Sheared Flow
- Open Access
- 5 June 2012
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 134 (5) , 051008
Acoustic Source Data for Medium Speed IC-Engines
Knowledge of the acoustic source characteristics of internal combustion engines (IC-engines) is of great importance when designing the exhaust duct system and its components to withstand the resulting dynamic loads and to reduce the exhaust noise emission. The goal of the present study is to numerically and experimentally investigate the medium speed IC-engine acoustic source characteristics, not only in the plane wave range but also in the high frequency range. The low frequency acoustic source characteristics were predicted by simulating the acoustic multiload measurements by using a one-dimensional process simulation code. The low frequency in-duct exhaust noise of a medium speed IC-engine can be quite accurately predicted. The high frequency source data is estimated by averaging the measured acoustic pressures with different methods; using the simple cross-spectra averaging method seems promising in this instance.
- 5 June 2012
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 134 (5) , 051008
Open AccessAcoustic Source Data for Medium Speed IC-Engines
Knowledge of the acoustic source characteristics of internal combustion engines (IC-engines) is of great importance when designing the exhaust duct system and its components to withstand the resulting dynamic loads and to reduce the exhaust noise emission. The goal of the present study is to numerically and experimentally investigate the medium speed IC-engine acoustic source characteristics, not only in the plane wave range but also in the high frequency range. The low frequency acoustic source characteristics were predicted by simulating the acoustic multiload measurements by using a one-dimensional process simulation code. The low frequency in-duct exhaust noise of a medium speed IC-engine can be quite accurately predicted. The high frequency source data is estimated by averaging the measured acoustic pressures with different methods; using the simple cross-spectra averaging method seems promising in this instance.
- 1 November 2011
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 130 (5) , 2639-2647
Experimental source characterization techniques for studying the acoustic properties of perforates under high level acoustic excitation
This paper discusses experimental techniques for obtaining the acoustic properties of in-duct samples with non-linear acoustic characteristic. The methods developed are intended both for studies of non-linear energy transfer to higher harmonics for samples only accessible from one side such as wall treatment in aircraft engine ducts or automotive exhaust systems and for samples accessible from both sides such as perforates or other top sheets. When harmonic sound waves are incident on the sample nonlinear energy transfer results in sound generation at higher harmonics at the sample (perforate) surface. The idea is that these sources can be characterized using linear system identification techniques similar to one-port or two-port techniques which are traditionally used for obtaining source data for in-duct sources such as IC-engines or fans. The starting point will be so called polyharmonic distortion modeling which is used for characterization of nonlinear properties of microwave systems. It will be shown how acoustic source data models can be expressed using this theory. Source models of different complexity are developed and experimentally tested. The results of the experimental tests show that these techniques can give results which are useful for understanding non-linear energy transfer to higher harmonics.
- 1 November 2011
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 130 (5) , 2639-2647
Experimental source characterization techniques for studying the acoustic properties of perforates under high level acoustic excitation
This paper discusses experimental techniques for obtaining the acoustic properties of in-duct samples with non-linear acoustic characteristic. The methods developed are intended both for studies of non-linear energy transfer to higher harmonics for samples only accessible from one side such as wall treatment in aircraft engine ducts or automotive exhaust systems and for samples accessible from both sides such as perforates or other top sheets. When harmonic sound waves are incident on the sample nonlinear energy transfer results in sound generation at higher harmonics at the sample (perforate) surface. The idea is that these sources can be characterized using linear system identification techniques similar to one-port or two-port techniques which are traditionally used for obtaining source data for in-duct sources such as IC-engines or fans. The starting point will be so called polyharmonic distortion modeling which is used for characterization of nonlinear properties of microwave systems. It will be shown how acoustic source data models can be expressed using this theory. Source models of different complexity are developed and experimentally tested. The results of the experimental tests show that these techniques can give results which are useful for understanding non-linear energy transfer to higher harmonics.
- 1 February 2007
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 299 (4-5) , 1094-1113
Modified multi-load method for nonlinear source characterisation
- 1 February 2007
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 299 (4-5) , 1094-1113
Modified multi-load method for nonlinear source characterisation