Hao Chang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hao Chang has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Wenchao Zhang
School of Mechanical Engineering and Automation Dalian Polytechnic University Dalian China
2 shared publications - Yu Liu
Dalian Jiaotong University
2 shared publications - Dapeng Yang
School of Mechanical Engineering, Dalian Jiaotong University, Dalian, People’s Republic of China
1 shared publication - Fujian Ma
School of Mechanical Engineering, Dalian Jiaotong University, Dalian 116028, China
1 shared publication - Mohammad Sharif Uddin
UniSA STEM, University of South Australia, Mawson Lakes, SA 5095, Australia
1 shared publication - Qingyu Yao
Faculty of Engineering, Huanghe Science and Technology University, Zhengzhou 450003, China
1 shared publication
Latest Publications
- Open Access
Numerical Simulation and Mechanism of Line Uniformity for Aerosol Jet-Printed Diamond Coatings
The large aspect ratio micro end mill is a critical tool for microstructure machining, and its performance directly determines processing quality and efficiency. Diamond coatings are commonly applied to cutting edges to enhance wear resistance and extend tool life. However, existing coating techniques often suffer from poor uniformity and inadequate consistency, limiting batch production and process stability. Aerosol jet printing (AJP) offers a cost-effective and highly controllable alternative for the efficient, large-scale deposition of diamond coatings on micro end mills, where precise control of line spacing is essential to achieving coating uniformity. In this study, a transient numerical model of droplet deposition in AJP is developed using computational fluid dynamics (CFD). The volume of fluid (VOF) method and the discrete phase model (DPM) are coupled to track liquid–gas interface deformation and diamond particle motion, enabling the dynamic evolution of droplet deposition to be captured. The effects of inter-droplet distance on deposition, spreading, coalescence, and line uniformity are systematically investigated. Droplet deposition mechanisms are analyzed under low-speed jetting conditions, while high-speed jetting simulations are conducted to reflect industrial processing scenarios. The results show that under low-speed jetting, droplets undergo spreading, contraction, and rebound, eventually forming a uniform cap-like structure. Under high-speed jetting, droplets exhibit a dispersed ring-shaped spreading pattern; although uniformity is slightly reduced, the spreading area and deposition efficiency are significantly increased. These findings provide a theoretical basis for optimizing AJP process parameters to achieve high-quality diamond coatings on micro end mills.
Open AccessNumerical Simulation and Mechanism of Line Uniformity for Aerosol Jet-Printed Diamond Coatings
The large aspect ratio micro end mill is a critical tool for microstructure machining, and its performance directly determines processing quality and efficiency. Diamond coatings are commonly applied to cutting edges to enhance wear resistance and extend tool life. However, existing coating techniques often suffer from poor uniformity and inadequate consistency, limiting batch production and process stability. Aerosol jet printing (AJP) offers a cost-effective and highly controllable alternative for the efficient, large-scale deposition of diamond coatings on micro end mills, where precise control of line spacing is essential to achieving coating uniformity. In this study, a transient numerical model of droplet deposition in AJP is developed using computational fluid dynamics (CFD). The volume of fluid (VOF) method and the discrete phase model (DPM) are coupled to track liquid–gas interface deformation and diamond particle motion, enabling the dynamic evolution of droplet deposition to be captured. The effects of inter-droplet distance on deposition, spreading, coalescence, and line uniformity are systematically investigated. Droplet deposition mechanisms are analyzed under low-speed jetting conditions, while high-speed jetting simulations are conducted to reflect industrial processing scenarios. The results show that under low-speed jetting, droplets undergo spreading, contraction, and rebound, eventually forming a uniform cap-like structure. Under high-speed jetting, droplets exhibit a dispersed ring-shaped spreading pattern; although uniformity is slightly reduced, the spreading area and deposition efficiency are significantly increased. These findings provide a theoretical basis for optimizing AJP process parameters to achieve high-quality diamond coatings on micro end mills.
- Open Access
- 19 June 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (6) , 972
Study on Solidification Process and Residual Stress of SiCp/Al Composites in EDM
To study the change of residual stress during heating and solidification of SiCp/Al composites, a one-way FSI (Fluid Structure Interaction) model for the solidification process of the molten material is presented. The model used process parameters to obtain the temperature distribution, liquid and solid-state material transformation, and residual stress. The crack initiated by the thermal stress in the recast layer was investigated, and a mathematical model of crack tip stress was proposed. The results showed a wide range of residual stresses from 44 MPa to 404 MPa. The model is validated using experimental data with three points on the surface layer.
- 19 June 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (6) , 972
Open AccessStudy on Solidification Process and Residual Stress of SiCp/Al Composites in EDM
To study the change of residual stress during heating and solidification of SiCp/Al composites, a one-way FSI (Fluid Structure Interaction) model for the solidification process of the molten material is presented. The model used process parameters to obtain the temperature distribution, liquid and solid-state material transformation, and residual stress. The crack initiated by the thermal stress in the recast layer was investigated, and a mathematical model of crack tip stress was proposed. The results showed a wide range of residual stresses from 44 MPa to 404 MPa. The model is validated using experimental data with three points on the surface layer.
- Open Access
- 1 January 2019
- Published by Taylor & Francis in Engineering Applications of Computational Fluid Mechanics
- Vol. 13 (1) , 1153-1164
Study of the thermal erosion, ejection and solidification processes of electrode materials during EDM
Due to the complexity of electrical discharge machining (EDM), there is no perfect theory to explain the mechanisms of material erosion, ejection and solidification during the machining process. Therefore, this paper analyzed the micro-process of a single-pulse discharge during EDM and studied the thermal erosion, ejection and solidification processes of the electrode materials. A thermal-fluid simulation model that considered melting-solidification was established. A mathematical model of vapor flow considering the impact pressure was developed, and it was compiled and loaded as a material ejection force in simulations with a user defined function (UDF). The changes in the material ejection, crater formation and material solidification processes at different discharge times were studied. Finally, the simulation results were verified by single-pulse material discharge experiments, which provided a reference for additional understanding of the micro material discharge processes during EDM.
- 1 January 2019
- Published by Taylor & Francis in Engineering Applications of Computational Fluid Mechanics
- Vol. 13 (1) , 1153-1164
Open AccessStudy of the thermal erosion, ejection and solidification processes of electrode materials during EDM
Due to the complexity of electrical discharge machining (EDM), there is no perfect theory to explain the mechanisms of material erosion, ejection and solidification during the machining process. Therefore, this paper analyzed the micro-process of a single-pulse discharge during EDM and studied the thermal erosion, ejection and solidification processes of the electrode materials. A thermal-fluid simulation model that considered melting-solidification was established. A mathematical model of vapor flow considering the impact pressure was developed, and it was compiled and loaded as a material ejection force in simulations with a user defined function (UDF). The changes in the material ejection, crater formation and material solidification processes at different discharge times were studied. Finally, the simulation results were verified by single-pulse material discharge experiments, which provided a reference for additional understanding of the micro material discharge processes during EDM.