Matt Ring
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Matt Ring has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
Yong Liu
ON Semiconductor, Portland, ME
3 shared publicationsBill Cowell
Corp. R&D ON Semiconductor
2 shared publicationsDarren Moore
Corp. R&D ON Semiconductor
2 shared publicationsDeborah Noble
Colleges of Nanoscale Science and Engineering, SUNY Polytechnic Institute, Albany, NY, USA
2 shared publicationsJeff Gambino
Corp. R&D ON Semiconductor
2 shared publicationsJihwan Kim
Fairchild Semiconductor, Bucheon, korea
2 shared publications
Latest Publications
- 11 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 9 (10) , 1993-1999
Modeling Effect of Grain Orientation on Degradation in Tin-Based Solder—Part II: Electromigration Experiments
In a series of papers, we consider the effects of the microstructure and the associated anisotropy of Sn grains on electromigration in lead-free solder bumps. In this paper, we carried out experiments to characterize microstructures of tin-based solder bumps and to investigate their effects on electromigration-induced failure. Accelerated electromigration tests and electron backscatter diffraction (EBSD) tests are performed on tin-based solder bumps in wafer level chip scale packages (WLCSP). EBSD analysis, together with the results of time to failure from accelerated electromigration tests, provides valuable information on the effects of the microstructure on electromigration-induced failure that can be used for predictive modeling. For Ni-based metallization, we find that tin self-diffusion is the dominant degradation mechanism and a strong effect of the grain orientation in the solder on the time to failure.
- 11 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 9 (10) , 1993-1999
Modeling Effect of Grain Orientation on Degradation in Tin-Based Solder—Part II: Electromigration Experiments
In a series of papers, we consider the effects of the microstructure and the associated anisotropy of Sn grains on electromigration in lead-free solder bumps. In this paper, we carried out experiments to characterize microstructures of tin-based solder bumps and to investigate their effects on electromigration-induced failure. Accelerated electromigration tests and electron backscatter diffraction (EBSD) tests are performed on tin-based solder bumps in wafer level chip scale packages (WLCSP). EBSD analysis, together with the results of time to failure from accelerated electromigration tests, provides valuable information on the effects of the microstructure on electromigration-induced failure that can be used for predictive modeling. For Ni-based metallization, we find that tin self-diffusion is the dominant degradation mechanism and a strong effect of the grain orientation in the solder on the time to failure.
- 1 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
BEOL Process Development Using Fast Power Cycling on Test Structures
Power semiconductors used in automotive applications are exposed to higher temperatures and higher currents than devices used in consumer products. The qualification of these devices includes power-temperature cycling (PTC) stresses on fully integrated structures where the devices are powered on and off during cyclic temperature stresses. These PTC stresses are time consuming and can require device redesign if fails are observed. Use of a simple power cycling (PC) stress, with simple test structures, can serve as a rapid assessment tool for process development. The PC test has no decoupling of current stress from temperature stress, meaning that electromigration and thermomechanical stress effects are applied simultaneously. The determination of the physics of failure is helpful to understand how to modify the process for robustness during development cycles. In this work it is shown how different back-end architectures influences the time to failure of the devices under the PC stress tests.
- 1 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
BEOL Process Development Using Fast Power Cycling on Test Structures
Power semiconductors used in automotive applications are exposed to higher temperatures and higher currents than devices used in consumer products. The qualification of these devices includes power-temperature cycling (PTC) stresses on fully integrated structures where the devices are powered on and off during cyclic temperature stresses. These PTC stresses are time consuming and can require device redesign if fails are observed. Use of a simple power cycling (PC) stress, with simple test structures, can serve as a rapid assessment tool for process development. The PC test has no decoupling of current stress from temperature stress, meaning that electromigration and thermomechanical stress effects are applied simultaneously. The determination of the physics of failure is helpful to understand how to modify the process for robustness during development cycles. In this work it is shown how different back-end architectures influences the time to failure of the devices under the PC stress tests.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Multiple Modes of Electromigration Failure in SAC Solder Alloys
The anisotropic nature of tin, the principle component of Pb-free solder, can cause significant variations the physical characteristics of the solder bumps. Grain size and orientation in a solder bump can drastically change the properties of one bump, giving rise to multiple potential failure modes between bumps. Electromigration may take place via grain boundary diffusion in one bump and interstitial diffusion in another. The greater the number of bumps in a test structure, the greater the probability of early failure resulting from large grains oriented in a direction that enables fast diffusion. The lognormal probability of electromigration failures can be expected to follow a linear trend. Deviation from this linear trend for the earliest failures suggests multiple modes of electromigration failure in the solder bump daisy chain.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Multiple Modes of Electromigration Failure in SAC Solder Alloys
The anisotropic nature of tin, the principle component of Pb-free solder, can cause significant variations the physical characteristics of the solder bumps. Grain size and orientation in a solder bump can drastically change the properties of one bump, giving rise to multiple potential failure modes between bumps. Electromigration may take place via grain boundary diffusion in one bump and interstitial diffusion in another. The greater the number of bumps in a test structure, the greater the probability of early failure resulting from large grains oriented in a direction that enables fast diffusion. The lognormal probability of electromigration failures can be expected to follow a linear trend. Deviation from this linear trend for the earliest failures suggests multiple modes of electromigration failure in the solder bump daisy chain.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Fast Power-Temperature Cycling of BEOL Test Structures for Power Devices
Power semiconductors used in automotive applications are exposed to higher temperatures and higher currents than devices used in consumer products. The qualification of these devices includes power-temperature cycling (PTC) stresses on fully integrated structures. The PTC stresses are time consuming and can require device redesign if fails are observed. In this report, we show that PTC stresses using simple test structures can be used to quickly test the interconnects and wire bonds, and thereby highlight weak links in the process.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Fast Power-Temperature Cycling of BEOL Test Structures for Power Devices
Power semiconductors used in automotive applications are exposed to higher temperatures and higher currents than devices used in consumer products. The qualification of these devices includes power-temperature cycling (PTC) stresses on fully integrated structures. The PTC stresses are time consuming and can require device redesign if fails are observed. In this report, we show that PTC stresses using simple test structures can be used to quickly test the interconnects and wire bonds, and thereby highlight weak links in the process.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Integrated solder bump electromigration test chip and coupon cards for the characterization of Pb-free SAC solders under stress
As silicon power integrated circuits continue to shrink in scale to enable inclusion in mobile devices, the use of wafer level chip scale packages (WLCSPs) is becoming more common. Power devices are typically used in applications where a high current device relies on multiple solder connections to pass current in applications such as battery chargers and USB input switches where power transmission is important. In such applications, the traditional failure mechanism of crack propagation due to drop/shock or temperature cycling of the solder bumps can be overshadowed by electromigration failures in the Sn alloy, as relatively low current densities are required to cause voiding. To characterize the electromigration behavior of Pb-free solder bumps used in wafer level chip scale packages (WLCSPs), a combined test chip / PCB card has been designed for flexibility of test. This test vehicle combines the JEDEC recommended single ball and daisy chain type test structures on a single chip, along with a serpentine resistor specifically for characterizing the temperature of the Under-Bump Metallization (UBM) and die surface. This added resistor not only aides in the careful characterization of bump temperature near the liquidus point of the solder alloy, but also enables an asymmetrical thermal migration tests where die temperature is held higher than ambient temperature. Imaging of failed solder bumps after high stress EM testing linking lifetime data and rapid changes in the solder bump test vehicle will provide direction for high-reliability solder bump design and materials.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Integrated solder bump electromigration test chip and coupon cards for the characterization of Pb-free SAC solders under stress
As silicon power integrated circuits continue to shrink in scale to enable inclusion in mobile devices, the use of wafer level chip scale packages (WLCSPs) is becoming more common. Power devices are typically used in applications where a high current device relies on multiple solder connections to pass current in applications such as battery chargers and USB input switches where power transmission is important. In such applications, the traditional failure mechanism of crack propagation due to drop/shock or temperature cycling of the solder bumps can be overshadowed by electromigration failures in the Sn alloy, as relatively low current densities are required to cause voiding. To characterize the electromigration behavior of Pb-free solder bumps used in wafer level chip scale packages (WLCSPs), a combined test chip / PCB card has been designed for flexibility of test. This test vehicle combines the JEDEC recommended single ball and daisy chain type test structures on a single chip, along with a serpentine resistor specifically for characterizing the temperature of the Under-Bump Metallization (UBM) and die surface. This added resistor not only aides in the careful characterization of bump temperature near the liquidus point of the solder alloy, but also enables an asymmetrical thermal migration tests where die temperature is held higher than ambient temperature. Imaging of failed solder bumps after high stress EM testing linking lifetime data and rapid changes in the solder bump test vehicle will provide direction for high-reliability solder bump design and materials.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Package reliability: How can we use ideas/methods from semiconductor reliability in package reliability?
Are the fields of fracture mechanics, rheology, etc. good enough to address issues In package reliability? No: JEDEC specs all based on DIP wirebond packages. Are we using results from these fields enough or most effectively? Not addressed. Biggest difference with wafer reliability is stressors on chip are local (E-field, temperature), which stressors in a package are mechanical stress, which is resultant of the entire package materials' CTE.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Package reliability: How can we use ideas/methods from semiconductor reliability in package reliability?
Are the fields of fracture mechanics, rheology, etc. good enough to address issues In package reliability? No: JEDEC specs all based on DIP wirebond packages. Are we using results from these fields enough or most effectively? Not addressed. Biggest difference with wafer reliability is stressors on chip are local (E-field, temperature), which stressors in a package are mechanical stress, which is resultant of the entire package materials' CTE.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Influences of the wafer-level testing method on unclamped inductive switching
For power MOSFETs used in industrial and automotive applications, the Unclamped Inductive Switching Safe-Operating Area (UIS-SOA) is critical for motion control, especially when used as a pulse-width modulation control device. The current after turn-off of the inductive load will flow through the device's source/body diode in an avalanche condition, placing a large current and thermal load on the device. Robustness to this loading is the key to the durability of the power MOSFET, and is described by the supported time in avalanche (tAV), the current in avalanche (IAV), and a ruggedness rating known as the K value. The process window for UIS is bounded by thermal failure at long times in avalanche (tAV) and by latch-up failure in high current, short tAV conditions where parasitic bipolar devices can activate and cause localized failure. Determination of the device capability in wafer level testing proves difficult as thin die are required for RDSon characterization while thick die are more robust to thermal failures, and the die thickness is shown to impact the IAV value at larger inductor values.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Influences of the wafer-level testing method on unclamped inductive switching
For power MOSFETs used in industrial and automotive applications, the Unclamped Inductive Switching Safe-Operating Area (UIS-SOA) is critical for motion control, especially when used as a pulse-width modulation control device. The current after turn-off of the inductive load will flow through the device's source/body diode in an avalanche condition, placing a large current and thermal load on the device. Robustness to this loading is the key to the durability of the power MOSFET, and is described by the supported time in avalanche (tAV), the current in avalanche (IAV), and a ruggedness rating known as the K value. The process window for UIS is bounded by thermal failure at long times in avalanche (tAV) and by latch-up failure in high current, short tAV conditions where parasitic bipolar devices can activate and cause localized failure. Determination of the device capability in wafer level testing proves difficult as thin die are required for RDSon characterization while thick die are more robust to thermal failures, and the die thickness is shown to impact the IAV value at larger inductor values.
- 18 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 538-543
Electromigration Induced Stress in Lead-Free Solder Joints
A finite element-based simulation approach is used to predict stress evolution resulting from electromigration-induced diffusion. A diffusion-mechanical coupled model is developed where the electromigration and stress-induced diffusion is coupled to the mechanical equilibrium with an introduction of the electromigration induced inelastic strain. A crystal plasticity constitutive model is developed to capture the plastic anisotropy of Sn. The problem is solved using a staggered approach at each time step. Simulations are conducted on a simplified geometry of a single crystal Sn cylinder and stress evolution is obtained with different current densities and Sn crystal orientations.
- 18 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 538-543
Electromigration Induced Stress in Lead-Free Solder Joints
A finite element-based simulation approach is used to predict stress evolution resulting from electromigration-induced diffusion. A diffusion-mechanical coupled model is developed where the electromigration and stress-induced diffusion is coupled to the mechanical equilibrium with an introduction of the electromigration induced inelastic strain. A crystal plasticity constitutive model is developed to capture the plastic anisotropy of Sn. The problem is solved using a staggered approach at each time step. Simulations are conducted on a simplified geometry of a single crystal Sn cylinder and stress evolution is obtained with different current densities and Sn crystal orientations.
- 1 October 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 138-142
Combined Vramp and TDDB analysis for gate oxide reliability assessment and screening
We present a gate oxide breakdown analysis method that uses an effective oxide thickness model combined with Time-Dependent Dielectric Breakdown (TDDB) model parameters to assess the reliability of extrinsic gate oxide defects. The method transforms gate breakdown voltage (Vbd), obtained from voltage ramp-to-breakdown measurements, into effective oxide thickness (teff) and compares these to the minimum oxide thickness that gives 10 or 20 years TDDB lifetimes. The analysis allows binning of extrinsic defects (Jedec mode B) into reliable and unreliable populations. It also gives an optimal gate screen voltage that can be used at wafer sort to screen parts with unreliable gate oxides. This method is valid for any CMOS process, but is especially useful for BCDMOS and Power Trench MOSFET technologies that use very large devices and ship in large volumes.
- 1 October 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 138-142
Combined Vramp and TDDB analysis for gate oxide reliability assessment and screening
We present a gate oxide breakdown analysis method that uses an effective oxide thickness model combined with Time-Dependent Dielectric Breakdown (TDDB) model parameters to assess the reliability of extrinsic gate oxide defects. The method transforms gate breakdown voltage (Vbd), obtained from voltage ramp-to-breakdown measurements, into effective oxide thickness (teff) and compares these to the minimum oxide thickness that gives 10 or 20 years TDDB lifetimes. The analysis allows binning of extrinsic defects (Jedec mode B) into reliable and unreliable populations. It also gives an optimal gate screen voltage that can be used at wafer sort to screen parts with unreliable gate oxides. This method is valid for any CMOS process, but is especially useful for BCDMOS and Power Trench MOSFET technologies that use very large devices and ship in large volumes.
- 1 May 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1230-1234
3D Power module with embedded WLCSP
The qualifications of a 2×3 and a 7×7 embedded WLCSP power module were shared in this paper. The 2×3 module was built on a switching voltage regulator with three passive components and one embedded WLCSP (2×3 at 0.4 mm pitch). The chip to module size ratio is 18.1 percent. The 7×7 module was built on a 7×7, 0.4 mm pitch WLCSP daisy chain test chip and five passive components. The silicon to module size ratio is 52.4 percent. Both 2×3 modules and 7×7 modules were subjected to drop test and temperature cycling test (TMCL). In addition, functional 2×3 modules underwent more device level reliability tests, such as dynamic optional life (DOPL), temperature humidity bias test (THBT), high temperature storage life (HTSL) and TMCL, etc. Solid chip to module, passives to module interconnect reliability was demonstrated alongside the robust module board level reliabilities. With adoption of PCB build up technology, the embedded WLCSP module offers 3D packaging options that are readily available to customers who demand full functionality in a small package and an attractive cost. Compared to other 3D packaging options, routing flexibility and robust interconnect reliability of the embedded module are distinguishing benefits. More designs taking advantages of this packaging technology are expected in the coming years.
- 1 May 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1230-1234
3D Power module with embedded WLCSP
The qualifications of a 2×3 and a 7×7 embedded WLCSP power module were shared in this paper. The 2×3 module was built on a switching voltage regulator with three passive components and one embedded WLCSP (2×3 at 0.4 mm pitch). The chip to module size ratio is 18.1 percent. The 7×7 module was built on a 7×7, 0.4 mm pitch WLCSP daisy chain test chip and five passive components. The silicon to module size ratio is 52.4 percent. Both 2×3 modules and 7×7 modules were subjected to drop test and temperature cycling test (TMCL). In addition, functional 2×3 modules underwent more device level reliability tests, such as dynamic optional life (DOPL), temperature humidity bias test (THBT), high temperature storage life (HTSL) and TMCL, etc. Solid chip to module, passives to module interconnect reliability was demonstrated alongside the robust module board level reliabilities. With adoption of PCB build up technology, the embedded WLCSP module offers 3D packaging options that are readily available to customers who demand full functionality in a small package and an attractive cost. Compared to other 3D packaging options, routing flexibility and robust interconnect reliability of the embedded module are distinguishing benefits. More designs taking advantages of this packaging technology are expected in the coming years.