Theodoros Anagnos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Theodoros Anagnos has a total of 89 co-authors. Here are the top co-authors by number of shared publications:
- Robert. J. Harris
Ctr. for Advanced Instrumentation, Durham Univ., Durham, UK
5 shared publications Matthias Blaicher
Karlsruhe Institute of Technology (KIT)
3 shared publications- Abani Shankar Nayak
Leibniz-Institut für Astrophysik Potsdam
2 shared publications Andreas Quirrenbach
Zentrum für Astronomie der Universität Heidelberg
2 shared publications- Andreas Quirrenbach
Landessternwarte Zentrum für Astronomie Universität Heidelberg Königstuhl 12 69117 Heidelberg Germany
2 shared publications - Christian Koos
Karlsruhe Institute of Technology (KIT)
2 shared publications
Latest Publications
- 9 August 2021
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 38 (9) , 2517-2527
On-sky results for the integrated microlens ring tip-tilt sensor
We present the first on-sky results of the microlens ring tip-tilt sensor. This sensor uses a 3D printed microlens ring feeding six multimode fibers to sense misaligned light, allowing centroid reconstruction. A tip-tilt mirror allows the beam to be corrected, increasing the amount of light coupled into a centrally positioned single-mode (science) fiber. The sensor was tested with the iLocater acquisition camera at the Large Binocular Telescope in Tucson, Arizona, in November 2019. The limit on the maximum achieved rms reconstruction accuracy was found to be 0.19 λ / D in both tip and tilt, of which approximately 50% of the power originates at frequencies below 10 Hz. We show the reconstruction accuracy is highly dependent on the estimated Strehl ratio and simulations support the assumption that residual adaptive optics aberrations are the main limit to the reconstruction accuracy. We conclude that this sensor is ideally suited to remove post-adaptive optics noncommon path tip-tilt residuals. We discuss the next steps for concept development, including optimization of the lens and the fiber, tuning of the correction algorithm, and selection of optimal science cases.
- 9 August 2021
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 38 (9) , 2517-2527
On-sky results for the integrated microlens ring tip-tilt sensor
We present the first on-sky results of the microlens ring tip-tilt sensor. This sensor uses a 3D printed microlens ring feeding six multimode fibers to sense misaligned light, allowing centroid reconstruction. A tip-tilt mirror allows the beam to be corrected, increasing the amount of light coupled into a centrally positioned single-mode (science) fiber. The sensor was tested with the iLocater acquisition camera at the Large Binocular Telescope in Tucson, Arizona, in November 2019. The limit on the maximum achieved rms reconstruction accuracy was found to be 0.19 λ / D in both tip and tilt, of which approximately 50% of the power originates at frequencies below 10 Hz. We show the reconstruction accuracy is highly dependent on the estimated Strehl ratio and simulations support the assumption that residual adaptive optics aberrations are the main limit to the reconstruction accuracy. We conclude that this sensor is ideally suited to remove post-adaptive optics noncommon path tip-tilt residuals. We discuss the next steps for concept development, including optimization of the lens and the fiber, tuning of the correction algorithm, and selection of optimal science cases.
- 23 June 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (19) , D108-D121
3D-M3: high-spatial-resolution spectroscopy with extreme AO and 3D-printed micro-lenslets
By combining integral field spectroscopy with extreme adaptive optics, we are now able to resolve objects close to the diffraction limit of large telescopes, exploring new science cases. We introduce an integral field unit designed to couple light with a minimal plate scale from the SCExAO facility at NIR wavelengths to a single-mode spectrograph. The integral field unit has a 3D-printed micro-lens array on top of a custom single-mode multi-core fiber, to optimize the coupling of light into the fiber cores. We demonstrate the potential of the instrument via initial results from the first on-sky runs at the 8.2 m Subaru Telescope with a spectrograph using off-the-shelf optics, allowing for rapid development with low cost.
- 23 June 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (19) , D108-D121
3D-M3: high-spatial-resolution spectroscopy with extreme AO and 3D-printed micro-lenslets
By combining integral field spectroscopy with extreme adaptive optics, we are now able to resolve objects close to the diffraction limit of large telescopes, exploring new science cases. We introduce an integral field unit designed to couple light with a minimal plate scale from the SCExAO facility at NIR wavelengths to a single-mode spectrograph. The integral field unit has a 3D-printed micro-lens array on top of a custom single-mode multi-core fiber, to optimize the coupling of light into the fiber cores. We demonstrate the potential of the instrument via initial results from the first on-sky runs at the 8.2 m Subaru Telescope with a spectrograph using off-the-shelf optics, allowing for rapid development with low cost.
- Open Access
- 13 December 2020
- Published by SPIE-Intl Soc Optical Eng
- p. 2
NAIR: novel astronomical instrumentation through photonic reformatting
SPIE Digital Library Proceedings
- 13 December 2020
- Published by SPIE-Intl Soc Optical Eng
- p. 2
Open AccessNAIR: novel astronomical instrumentation through photonic reformatting
SPIE Digital Library Proceedings
- 1 October 2020
- Published by SPIE-Intl Soc Optical Eng in Journal of Astronomical Telescopes, Instruments, and Systems
- Vol. 6 (04) , 045007-24
Diffraction-limited integral-field spectroscopy for extreme adaptive optics systems with the multicore fiber-fed integral-field unit
Direct imaging instruments have the spatial resolution to resolve exoplanets from their host star. This enables direct characterization of the exoplanets atmosphere, but most direct imaging instruments do not have spectrographs with high enough resolving power for detailed atmospheric characterization. We investigate the use of a single-mode diffraction-limited integral-field unit that is compact and easy to integrate into current and future direct imaging instruments for exoplanet characterization. This achieved by making use of recent progress in photonic manufacturing to create a single-mode fiber-fed image reformatter. The fiber link is created with three-dimensional printed lenses on top of a single-mode multicore fiber that feeds an ultrafast laser inscribed photonic chip that reformats the fiber into a pseudoslit. We then couple it to a first-order spectrograph with a triple stacked volume phase holographic grating for a high efficiency over a large bandwidth. The prototype system has had a successful first-light observing run at the 4.2-m William Herschel Telescope. The measured on-sky resolving power is between 2500 and 3000, depending on the wavelength. With our observations, we show that single-mode integral-field spectroscopy is a viable option for current and future exoplanet imaging instruments.
- 1 October 2020
- Published by SPIE-Intl Soc Optical Eng in Journal of Astronomical Telescopes, Instruments, and Systems
- Vol. 6 (04) , 045007-24
Diffraction-limited integral-field spectroscopy for extreme adaptive optics systems with the multicore fiber-fed integral-field unit
Direct imaging instruments have the spatial resolution to resolve exoplanets from their host star. This enables direct characterization of the exoplanets atmosphere, but most direct imaging instruments do not have spectrographs with high enough resolving power for detailed atmospheric characterization. We investigate the use of a single-mode diffraction-limited integral-field unit that is compact and easy to integrate into current and future direct imaging instruments for exoplanet characterization. This achieved by making use of recent progress in photonic manufacturing to create a single-mode fiber-fed image reformatter. The fiber link is created with three-dimensional printed lenses on top of a single-mode multicore fiber that feeds an ultrafast laser inscribed photonic chip that reformats the fiber into a pseudoslit. We then couple it to a first-order spectrograph with a triple stacked volume phase holographic grating for a high efficiency over a large bandwidth. The prototype system has had a successful first-light observing run at the 4.2-m William Herschel Telescope. The measured on-sky resolving power is between 2500 and 3000, depending on the wavelength. With our observations, we show that single-mode integral-field spectroscopy is a viable option for current and future exoplanet imaging instruments.
- Open Access
- 10 July 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10706, 107060L-20
NAIR: novel astronomical instrumentation through photonic reformatting
The project "Novel Astronomical Instrumentation based on photonic light Reformating" is a DFG-funded collaboration to exploit the recognized potential of photonics solutions for a radically new approach to astronomical instrumentation for optical/infrared high precision spectroscopy and high angular resolution imaging. We present a project overview and initial development results from our Adaptive Optics-photonic test bed, Ultrafast Laser Inscribed waveguides for interferometric beam combination and 3D printing structures for astronomical instrumentation. The project is expected to lead to important technological breakthroughs facilitating uniquely functionality and technical solutions for the next generation of instrumentation.
- 10 July 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10706, 107060L-20
Open AccessNAIR: novel astronomical instrumentation through photonic reformatting
The project "Novel Astronomical Instrumentation based on photonic light Reformating" is a DFG-funded collaboration to exploit the recognized potential of photonics solutions for a radically new approach to astronomical instrumentation for optical/infrared high precision spectroscopy and high angular resolution imaging. We present a project overview and initial development results from our Adaptive Optics-photonic test bed, Ultrafast Laser Inscribed waveguides for interferometric beam combination and 3D printing structures for astronomical instrumentation. The project is expected to lead to important technological breakthroughs facilitating uniquely functionality and technical solutions for the next generation of instrumentation.
- Open Access
- 28 May 2018
- Published by Oxford University Press (OUP) in Monthly Notices of the Royal Astronomical Society
- Vol. 478 (4) , 4881-4889
Simulation and optimisation of an astrophotonic reformatter
- 28 May 2018
- Published by Oxford University Press (OUP) in Monthly Notices of the Royal Astronomical Society
- Vol. 478 (4) , 4881-4889
Open AccessSimulation and optimisation of an astrophotonic reformatter