Astrid Ahlinder
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Astrid Ahlinder has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Anna Finne-Wistrand
Department of Fibre and Polymer Technology, School of Engineering Sciences in Chemistry, Biotechnology and Health, KTH Royal Institute of Technology, Teknikringen, 56-58, SE 10044 Stockholm, Sweden
3 shared publications - Tiziana Fuoco
Department of Fibre and Polymer Technology School of Engineering Sciences in Chemistry, Biotechnology and Health KTH Royal Institute of Technology Teknikringen, 56–58 100-44 Stockholm Sweden
3 shared publications Johanna Eckardt
2 shared publicationsAnne Normann
1 shared publicationAnnika Altskär
1 shared publicationAnnika Krona
1 shared publication
Latest Publications
- 15 July 2025
- Published by Elsevier in Food Hydrocolloids
- Vol. 171
The influence of wax-based oleogelators on microstructure evolution, rheology and diffusion
- 15 July 2025
- Published by Elsevier in Food Hydrocolloids
- Vol. 171
The influence of wax-based oleogelators on microstructure evolution, rheology and diffusion
- Open Access
- 19 June 2025
- Published by Elsevier in International Journal of Gastronomy and Food Science
- Vol. 41
“It's not bad, but it's not chicken”: Sensorial drivers of liking and their correlates for plant-based chicken analogues in Sweden
- 19 June 2025
- Published by Elsevier in International Journal of Gastronomy and Food Science
- Vol. 41
Open Access“It's not bad, but it's not chicken”: Sensorial drivers of liking and their correlates for plant-based chicken analogues in Sweden
- Open Access
Saltiness enhancement: Impact of acid added to bread with heterogeneously distributed sodium chloride
- Open Access
- 12 August 2021
- Published by American Chemical Society (ACS) in ACS Polymers Au
- Vol. 1 (2) , 107-122
Pliable, Scalable, and Degradable Scaffolds with Varying Spatial Stiffness and Tunable Compressive Modulus Produced by Adopting a Modular Design Strategy at the Macrolevel
- 12 August 2021
- Published by American Chemical Society (ACS) in ACS Polymers Au
- Vol. 1 (2) , 107-122
Open AccessPliable, Scalable, and Degradable Scaffolds with Varying Spatial Stiffness and Tunable Compressive Modulus Produced by Adopting a Modular Design Strategy at the Macrolevel
- 14 October 2019
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (15)
Nondegradative additive manufacturing of medical grade copolyesters of high molecular weight and with varied elastic response
Although additive manufacturing through melt extrusion has become increasingly popular as a route to design scaffolds with complex geometries the technique if often limited by the reduction in molecular weight and the viscoelastic response when degradable aliphatic polyesters of high molecular weight are used. Here we use a melt extruder and fused filament fabrication printer to produce a reliable nondegradative route for scaffold fabrication of medical grade copolymers of L‐lactide, poly(ε‐caprolactone‐co‐L‐lactide), and poly(L‐lactide‐co‐trimethylene carbonate). We show that degradation is avoided using filament extrusion and fused filament fabrication if the process parameters are deliberately chosen based upon the rheological behavior, mechanical properties, and polymer composition. Structural, mechanical, and thermal properties were assessed throughout the process to obtain comprehension of the relationship between the rheological properties and the behavior of the medical grade copolymers in the extruder and printer. Scaffolds with a controlled architecture were achieved using high‐molecular‐weight polyesters exhibiting a large range in the elastic response causing negligible degradation of the polymers. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48550.
- 14 October 2019
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (15)
Nondegradative additive manufacturing of medical grade copolyesters of high molecular weight and with varied elastic response
Although additive manufacturing through melt extrusion has become increasingly popular as a route to design scaffolds with complex geometries the technique if often limited by the reduction in molecular weight and the viscoelastic response when degradable aliphatic polyesters of high molecular weight are used. Here we use a melt extruder and fused filament fabrication printer to produce a reliable nondegradative route for scaffold fabrication of medical grade copolymers of L‐lactide, poly(ε‐caprolactone‐co‐L‐lactide), and poly(L‐lactide‐co‐trimethylene carbonate). We show that degradation is avoided using filament extrusion and fused filament fabrication if the process parameters are deliberately chosen based upon the rheological behavior, mechanical properties, and polymer composition. Structural, mechanical, and thermal properties were assessed throughout the process to obtain comprehension of the relationship between the rheological properties and the behavior of the medical grade copolymers in the extruder and printer. Scaffolds with a controlled architecture were achieved using high‐molecular‐weight polyesters exhibiting a large range in the elastic response causing negligible degradation of the polymers. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48550.